Accessories
- Batteries
- Electronics
- Generators
- Installation
- Complete Systems
- Brands
Filter
–
Accessories
6 Results
Sorting
8-96-017910
Fothermo Photovoltaic boiler to feed-in changeover unit
Use the switching device from Fothermo (mpn swd-1600) to feed surplus electricity directly into the household grid when your photovoltaic boiler is fully heated. using a plug & play micro PV inverter, the switching device feeds up to 3.5 kWh of excess electrical energy per day into your power grid so that no more valuable energy is lost, actively contributing to climate protection and saving CO2-Emissions and unnecessary electricity costs every day. (Micro inverter must be purchased separately) Your benefits with a switching device: Intelligent control Feed-in of up to 3.5 kWh of electricity/day Connection for up to 4 modules (max. 1,600 W) Simple installation thanks to safety extra-low voltage No electrician required User-friendly operation Environmentally friendly Climate-friendly and cost-effective Up to 1600 Wp of photovoltaic power can be connected to the system. However, as a maximum of 600 W is fed in via the inverter, no additional registration is required in most cases and you can optimize your energy supply cost-effectively. Particularly in the summer months, when the photovoltaic boiler is already heated up in the morning, the switching device switches individual pv modules to the connected micro-pv inverter. This means you can easily benefit from the solar energy generated throughout the day. Do you already have a balcony power plant and want to store the surplus electricity? The Fothermo switching device allows you to easily store the energy directly in the boiler and continue to feed the surplus energy into your home grid. User-friendly The changeover unit has a display that shows the status of all connected electrical consumers, so you always have an overview. Wall mounting is effortless with just four screws. The connection of photovoltaic modules and electrical loads is just as straightforward thanks to simple screw terminals on the device. Four pv inputs and up to three connections for electrical consumers offer flexibility and easy handling. All you need is a screwdriver and mc4 contact plugs for the consumer connections. Compatible Fothermo is committed to compatible components, so they have also developed the switching device to be compatible with a wide range of micro pv inverters. Just make sure that your inverter has a voltage range of less than 60v and use brands such as Hoymiles, Envertech or Deye for the best results. Also note that the Growatt inverters are unfortunately not compatible. Technical data: Number of connectable modules: 4 Recommended pv power per input: 300-450 W Max. Open-circuit voltage: 50 VOC Max. Short-circuit current/module: 12 A Connectable pv boiler: 600 W Connectable micro inverters: 2×300 W IP class: 20 Dimensions: 17.9×7.6×4.1 cm Weight: 0.4 kg Scope of delivery: 1× Fothermo changeover unit 1× Operating instructions
Use the switching device from Fothermo (mpn swd-1600) to feed surplus electricity directly into the household grid when your photovoltaic boiler is fu...
Soon available again
Soon available again
Use the switching device from Fothermo (mpn swd-1600) to feed surplus electricity directly into the household grid when your photovoltaic boiler is fully heated. using a plug & play micro PV inverter, the switching device feeds up to 3.5 kWh of excess electrical energy per day into your power grid so that no more valuable energy is lost, actively contributing to climate protection and saving CO2-Emissions and unnecessary electricity costs every day. (Micro inverter must be purchased separately) Your benefits with a switching device: Intelligent control Feed-in of up to 3.5 kWh of electricity/day Connection for up to 4 modules (max. 1,600 W) Simple installation thanks to safety extra-low voltage No electrician required User-friendly operation Environmentally friendly Climate-friendly and cost-effective Up to 1600 Wp of photovoltaic power can be connected to the system. However, as a maximum of 600 W is fed in via the inverter, no additional registration is required in most cases and you can optimize your energy supply cost-effectively. Particularly in the summer months, when the photovoltaic boiler is already heated up in the morning, the switching device switches individual pv modules to the connected micro-pv inverter. This means you can easily benefit from the solar energy generated throughout the day. Do you already have a balcony power plant and want to store the surplus electricity? The Fothermo switching device allows you to easily store the energy directly in the boiler and continue to feed the surplus energy into your home grid. User-friendly The changeover unit has a display that shows the status of all connected electrical consumers, so you always have an overview. Wall mounting is effortless with just four screws. The connection of photovoltaic modules and electrical loads is just as straightforward thanks to simple screw terminals on the device. Four pv inputs and up to three connections for electrical consumers offer flexibility and easy handling. All you need is a screwdriver and mc4 contact plugs for the consumer connections. Compatible Fothermo is committed to compatible components, so they have also developed the switching device to be compatible with a wide range of micro pv inverters. Just make sure that your inverter has a voltage range of less than 60v and use brands such as Hoymiles, Envertech or Deye for the best results. Also note that the Growatt inverters are unfortunately not compatible. Technical data: Number of connectable modules: 4 Recommended pv power per input: 300-450 W Max. Open-circuit voltage: 50 VOC Max. Short-circuit current/module: 12 A Connectable pv boiler: 600 W Connectable micro inverters: 2×300 W IP class: 20 Dimensions: 17.9×7.6×4.1 cm Weight: 0.4 kg Scope of delivery: 1× Fothermo changeover unit 1× Operating instructions
Soon available again
8-96-013635
Fothermo psu charger 230v / 18v
With the 230v/18v psu charger (mpn psu-18) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods of bad weather without having to do without hot water. The device serves as a mains-powered AC/DC converter that provides a regulated DC voltage for the water heater. Technical data Compatible with Fothermo 30l & 80l water boiler Input voltage range: 100-240V/AC Max. Power consumption: 2.5A AC connector: IEC320-C14 Output voltage: 18V/DC Heating power on photovoltaic boiler: 140W Ambient temperature range: -10°c - +40°C Scope of delivery: 1x Fothermo psu charger 230v/18v (psu-18)
With the 230v/18v psu charger (mpn psu-18) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods ...
Shipped in 1-3 days
Shipped in 1-3 days
8-96-013635
Fothermo psu charger 230v / 18v
With the 230v/18v psu charger (mpn psu-18) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods of bad weather without having to do without hot water. The device serves as a mains-powered AC/DC converter that provides a regulated DC voltage for the water heater. Technical data Compatible with Fothermo 30l & 80l water boiler Input voltage range: 100-240V/AC Max. Power consumption: 2.5A AC connector: IEC320-C14 Output voltage: 18V/DC Heating power on photovoltaic boiler: 140W Ambient temperature range: -10°c - +40°C Scope of delivery: 1x Fothermo psu charger 230v/18v (psu-18)
Shipped in 1-3 days
10,90 %
8-96-013640
Fothermo psu charger 230v / 24v
With the 230v/24v psu charger (mpn psu-24) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods of bad weather without having to do without hot water. The device serves as a mains-powered AC/DC converter that provides a regulated DC voltage for the water heater. Technical data Compatible with Fothermo water boiler Input voltage range: 100-240V/AC Max. Current consumption: 2.5A AC connector: IEC320-C14 Output voltage: 24V/DC Ambient temperature range: -10°c - +40°C Scope of delivery: 1x Fothermo psu charger 230v/24v (psu-24)
With the 230v/24v psu charger (mpn psu-24) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods ...
Shipped in 1-3 days
Shipped in 1-3 days
8-96-013640
Fothermo psu charger 230v / 24v
10,90 %
With the 230v/24v psu charger (mpn psu-24) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods of bad weather without having to do without hot water. The device serves as a mains-powered AC/DC converter that provides a regulated DC voltage for the water heater. Technical data Compatible with Fothermo water boiler Input voltage range: 100-240V/AC Max. Current consumption: 2.5A AC connector: IEC320-C14 Output voltage: 24V/DC Ambient temperature range: -10°c - +40°C Scope of delivery: 1x Fothermo psu charger 230v/24v (psu-24)
Shipped in 1-3 days
6,09 %
8-96-013645
Fothermo 3m Battery cable
With this 3m battery cable (MPN BC-03), Fothermo water boilers can be connected directly to a suitable battery and heated. This allows excess energy from photovoltaically charged batteries to be converted into heat in the boiler.
The Fothermo boilers can be used with 12V and 24V batteries. Depending on the mode set, the boiler either uses the energy provided by the battery immediately or the surplus energy after the battery is fully charged.
The 10 litre boiler can be charged excellently via a 12V or 24V battery system.
The 30-litre boiler can easily be charged via a 24V battery. If it were heated with a 12V battery, the heating times would be very long.
The 80 litre boiler can be charged via the 24V battery. However, the relatively long heating times must be taken into account here. Depending on the application and water consumption, this can still be useful.
Scope of delivery:
1x Fothermo 3m battery cable (BC-03)
3 Meter (€7.20* / 1 Meter)
Content: 3 Meter (€7.20* / 1 Meter)
With this 3m battery cable (MPN BC-03), Fothermo water boilers can be connected directly to a suitable battery and heated. This allows excess energy f...
Shipped in 1-3 days
Shipped in 1-3 days
8-96-013645
Fothermo 3m Battery cable
6,09 %
With this 3m battery cable (MPN BC-03), Fothermo water boilers can be connected directly to a suitable battery and heated. This allows excess energy from photovoltaically charged batteries to be converted into heat in the boiler.
The Fothermo boilers can be used with 12V and 24V batteries. Depending on the mode set, the boiler either uses the energy provided by the battery immediately or the surplus energy after the battery is fully charged.
The 10 litre boiler can be charged excellently via a 12V or 24V battery system.
The 30-litre boiler can easily be charged via a 24V battery. If it were heated with a 12V battery, the heating times would be very long.
The 80 litre boiler can be charged via the 24V battery. However, the relatively long heating times must be taken into account here. Depending on the application and water consumption, this can still be useful.
Scope of delivery:
1x Fothermo 3m battery cable (BC-03)
Shipped in 1-3 days
8-96-013645
Fothermo 3m Battery cable
3 Meter (€7.20* / 1 Meter)
Content: 3 Meter (€7.20* / 1 Meter)
8-96-013630
Fothermo psu charger 230v / 12v
With the 230v/12v psu charger (mpn psu-12) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods of bad weather without having to do without hot water. The device serves as a mains-powered AC/DC converter that provides a regulated DC voltage for the water heater. Technical data Compatible with Fothermo 10l water boiler Input voltage range: 100-240V/AC Max. Power consumption: 2.5A AC connector: IEC320-C14 Output voltage: 12V/DC Heating power on photovoltaic boiler: 62W Ambient temperature range: -10°c - +40°C Scope of delivery: 1x Fothermo psu charger 230v/12v (psu-12)
With the 230v/12v psu charger (mpn psu-12) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods ...
Shipped in 1-3 days
Shipped in 1-3 days
8-96-013630
Fothermo psu charger 230v / 12v
With the 230v/12v psu charger (mpn psu-12) you can additionally heat your Fothermo water boiler via the mains. This allows you to bridge long periods of bad weather without having to do without hot water. The device serves as a mains-powered AC/DC converter that provides a regulated DC voltage for the water heater. Technical data Compatible with Fothermo 10l water boiler Input voltage range: 100-240V/AC Max. Power consumption: 2.5A AC connector: IEC320-C14 Output voltage: 12V/DC Heating power on photovoltaic boiler: 62W Ambient temperature range: -10°c - +40°C Scope of delivery: 1x Fothermo psu charger 230v/12v (psu-12)
Shipped in 1-3 days
8-96-017905
Fothermo Photovoltaischer Heizstab für Warmwasserboiler
Mit dem Photovoltaischen Heizstab von Fothermo (MPN: HROD-550) gestaltet sich die photovoltaische Nachrüstung deines bestehenden Warmwasserboilers so einfach wie nie zuvor. Der innovative Photovoltaikheizstab wird dazu einfach in das übliche 1,5"-Gewinde eingeschraubt und ermöglicht dir so die Nutzung von Solarenergie zur Warmwasserbereitung anstelle herkömmlicher Gas- oder Ölheizungen. Und das Beste daran: Es ist keine Anmeldung dazu erforderlich, da der Heizstab nicht ins Stromnetz einspeist.
Die Vorteile im Überblick:
Einfache Nachrüstung
Schnelle Installation
Patentierter MPP-Tracker mit 99,9% Wirkungsgrad
Integrierter Verpolungsschutz
Keine Anmeldung erforderlich
Umweltfreundlich
Schutzklasse: IP24
Digitales Display
Nachrüstung via Plug & Play
Die Installation des Photovoltaischen Heizstabs von fothermo ist kinderleicht. Der Photovoltaikheizstab wird einfach in den handelsüblichen 1,5"-Flansch deines vorhandenen Warmwasserspeichers eingeschraubt und die PV-Module durch einfache Plug-and-Play-MC4-Verbindungen in Parallelschaltung angeschlossen. Der Heizvorgangn beginnt dann sofort und da auf komplizierte Verkabelungen verzichtet wurde und das Spannungsniveau unter 50 V liegt, wird für die Installation auch kein Elektriker benötigt. Die Heizstäbe sind darüber hinaus auch problemlos mit dem fothermo Umschaltgerät (MPN: SWD-1600) kombinierbar. Das Wasser im Boiler wird dann vorrangig von oben nach unten erwärmt, und überschüssige Energie wird über den Mikro-PV-Wechselrichter am Umschaltgerät in das Hausnetz eingespeist.
Warmwasserversorgung durch Sonnenkraft
Besonders im Sommer kannst du durch die Nachrüstung auf ineffiziente Gas- oder Ölheizungen zur Warmwasserbereitung verzichten. Stattdessen genießt du deine umweltfreundliche Dusche, die von der Sonne erwärmt wird, und trägst zur Reduzierung von CO2-Emissionen bei. Dank des innovativen MPP-Trackers sicherst du dir zudem 50% höhere Erträge und holst auch bei schlechterem Wetter die maximalen Erträge aus deinen PV-Modulen. Der Heizstab ermöglicht den Anschluss von bis zu 2000 Wp Photovoltaikleistung, während die maximale Heizleistung bei 500 W liegt. Dies bedeutet, dass die Warmwasserversorgung eines 2-Personen-Haushalts im Sommerhalbjahr bei einer maximalen Wassertemperatur von 65°C in Trinkwassersystemen oder 85°C in entkalkten Heizungssystemen nahezu vollständig abgedeckt werden kann.
Technische Daten:
Max. photovolt. Heizleistung: 550 W
Max. photovolt. Stromaufnahme: 15,5 A
Max. Wassertemperatur: 85 °C
Wasseranschluss: G 11/2 (M)
PV-Anschluss: MC4
Empf. PV-Leistung: 300-1.200 Wp
Max. PV-Leistung: 2.000 Wp
Max. Leerlaufspannung: 50 Voc
Abmessungen Gehäuse: 10×15,4×13,4 cm
Abmessungen Heizstab: 41,5×15,4×13,4 cm
Gewicht: 0,8 kg
Lieferumfang:
1× photovoltaischer Heizstab
Mit dem Photovoltaischen Heizstab von Fothermo (MPN: HROD-550) gestaltet sich die photovoltaische Nachrüstung deines bestehenden Warmwasserboiler...
Soon available again
Soon available again
Mit dem Photovoltaischen Heizstab von Fothermo (MPN: HROD-550) gestaltet sich die photovoltaische Nachrüstung deines bestehenden Warmwasserboilers so einfach wie nie zuvor. Der innovative Photovoltaikheizstab wird dazu einfach in das übliche 1,5"-Gewinde eingeschraubt und ermöglicht dir so die Nutzung von Solarenergie zur Warmwasserbereitung anstelle herkömmlicher Gas- oder Ölheizungen. Und das Beste daran: Es ist keine Anmeldung dazu erforderlich, da der Heizstab nicht ins Stromnetz einspeist.
Die Vorteile im Überblick:
Einfache Nachrüstung
Schnelle Installation
Patentierter MPP-Tracker mit 99,9% Wirkungsgrad
Integrierter Verpolungsschutz
Keine Anmeldung erforderlich
Umweltfreundlich
Schutzklasse: IP24
Digitales Display
Nachrüstung via Plug & Play
Die Installation des Photovoltaischen Heizstabs von fothermo ist kinderleicht. Der Photovoltaikheizstab wird einfach in den handelsüblichen 1,5"-Flansch deines vorhandenen Warmwasserspeichers eingeschraubt und die PV-Module durch einfache Plug-and-Play-MC4-Verbindungen in Parallelschaltung angeschlossen. Der Heizvorgangn beginnt dann sofort und da auf komplizierte Verkabelungen verzichtet wurde und das Spannungsniveau unter 50 V liegt, wird für die Installation auch kein Elektriker benötigt. Die Heizstäbe sind darüber hinaus auch problemlos mit dem fothermo Umschaltgerät (MPN: SWD-1600) kombinierbar. Das Wasser im Boiler wird dann vorrangig von oben nach unten erwärmt, und überschüssige Energie wird über den Mikro-PV-Wechselrichter am Umschaltgerät in das Hausnetz eingespeist.
Warmwasserversorgung durch Sonnenkraft
Besonders im Sommer kannst du durch die Nachrüstung auf ineffiziente Gas- oder Ölheizungen zur Warmwasserbereitung verzichten. Stattdessen genießt du deine umweltfreundliche Dusche, die von der Sonne erwärmt wird, und trägst zur Reduzierung von CO2-Emissionen bei. Dank des innovativen MPP-Trackers sicherst du dir zudem 50% höhere Erträge und holst auch bei schlechterem Wetter die maximalen Erträge aus deinen PV-Modulen. Der Heizstab ermöglicht den Anschluss von bis zu 2000 Wp Photovoltaikleistung, während die maximale Heizleistung bei 500 W liegt. Dies bedeutet, dass die Warmwasserversorgung eines 2-Personen-Haushalts im Sommerhalbjahr bei einer maximalen Wassertemperatur von 65°C in Trinkwassersystemen oder 85°C in entkalkten Heizungssystemen nahezu vollständig abgedeckt werden kann.
Technische Daten:
Max. photovolt. Heizleistung: 550 W
Max. photovolt. Stromaufnahme: 15,5 A
Max. Wassertemperatur: 85 °C
Wasseranschluss: G 11/2 (M)
PV-Anschluss: MC4
Empf. PV-Leistung: 300-1.200 Wp
Max. PV-Leistung: 2.000 Wp
Max. Leerlaufspannung: 50 Voc
Abmessungen Gehäuse: 10×15,4×13,4 cm
Abmessungen Heizstab: 41,5×15,4×13,4 cm
Gewicht: 0,8 kg
Lieferumfang:
1× photovoltaischer Heizstab
Soon available again