The us3000c (mpn us3000c) is a lithium storage system of the latest generation. The accumulator was specially developed to fully meet the high demands placed on a solar accumulator today. Maximum safety and a long service life are guaranteed even with regular deep discharge thanks to the latest technology. The latest battery of the market-leading manufacturer with now 3.5 kWh per module has again a battery management system (bms) built into each module and therefore offers a lot of security. Internally, the individual cells are thus monitored and balanced against overvoltage, overtemperature, deep discharge, etc. protected. The battery is compatible and certified with many available inverters. Features Extremely cycle resistant - over 6000 cycles at 95% DoD More usable energy content than the previous model US3000 Lifetime over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging power possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function capable of reducing the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects each installed battery cell from harmful influences over the entire life of the module and effectively prevents premature failure. Protection against: Deep discharge and overcharge overvoltage during charging excessive currents during charging and discharging over and under temperature Short circuit and reverse polarity Constant monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the desired storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) accumulator and an integrated BMS. High cycle life The extremely high cycle life of the installed LiFePo4 cells make Pylontech us3000c modules the optimal storage solution for photovoltaic systems. Regardless of whether the solar system is grid-connected or stand-alone, the Pylontech storage system offers several advantages over typical lead-acid batteries and other lithium technologies. Technical data Battery Type: Lithium Iron Phosphate (LiFePo4) Rated voltage: 48V Rated capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (Discharge) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Temperature range charge: 0°C - +50°C Temperature range discharge: -10°C - +50°C Temperature range storage: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 years manufacturer warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by freight forwarding! Scope of delivery: 1x Pylontech us3000c LiFePO4 3.5 kWh 1x cable set parallel connection incl. grounding 1x rj45 data cable 1x mounting screws 1x user manual
From
€1,004.17*
From €843.84**
The us3000c (mpn us3000c) is a lithium storage system of the latest generation. The accumulator was specially developed to fully meet the high demands...
The Pytes e-box 48100r-c (mpn 110402100007) is a state-of-the-art LFP battery with 100 Ah capacity and is characterized by its high level of safety, sophisticated design and impressive performance. The battery is compact, easy to install, maintenance-free and can be used as the basic building block of an energy storage system by connecting it in parallel. Applications range from self-consumption coverage in private homes to small commercial and industrial energy storage systems, as well as in telecommunication stations.The Pytes E-BoxLatest generation LFP storageOver 6000 cycles at 90% DoDIntelligent energy managementIdeal for emergency power supplyExtensive compatibilityModularly expandableCAN and rs485 communicationIntelligent energy managementThe intelligent Pytes battery offers a comprehensive energy management system. Through real-time measurements, monitoring and management, it optimizes the system service life using intelligent algorithms. The battery thus ensures efficient and sustainable use of the available energy.Reliable emergency power supplyThe simple installation and user-friendly design make Pytes batteries a practical option for ensuring an uninterrupted power supply in your home. With their intelligent control features, Pytes batteries can optimize energy consumption and maximize battery life to ensure your backup power supply is efficient and reliable.Long service life and maximum safetyPytes batteries are characterized by their impressive service life and high level of safety. With over 6000 cycles at 90% depth of discharge (dod), they offer an exceptionally long service life. Whether it is a grid-connected solar system or a self-sufficient stand-alone system, the Pytes storage system offers several clear advantages over conventional lead batteries and other lithium technologies.Technical dataBattery chemistry: Lithium iron phosphate (LFP)Nominal voltage: 51.2 VVoltage range: 47.5-57.6 VNominal power: 100 AhNominal energy: 5.12 kWhMax. Charging current: 50 AMax. Discharge: 50 ACharging temperature: 0~50°CDischarging temperature: -10~50°CEfficiency: =95%Communication protocol: rs-232, rs-485, CANCycle life: >6000 cycles at 90% DoDDimensions: 440 x 620 x 117 mmWeight: 51 kgScope of delivery:1x Pytes E-Box 48100r-c
€1,307.81*
€1,099.00**
The Pytes e-box 48100r-c (mpn 110402100007) is a state-of-the-art LFP battery with 100 Ah capacity and is characterized by its high level of safety, s...
The Offgridtec MPPT Pro-Duo (MPN 1-01-011200) is an innovative high-end solar controller that was essentially designed for mobile applications. A variety of different board battery types can be charged via the primary charging output (BATT-1). The battery spectrum ranges from AGM, GEL and liquid lead acid to state-of-the-art LiFePO4 and Li-NiCoMn battery systems. The secondary battery charge output (BATT-2) is designed for a starter battery that is at the same voltage level as BATT-1. The unit automatically detects the system voltage of the starter battery (BATT-2) and charging of the BATT-2 begins as soon as the preset conditions are met.
The controller uses the advanced MPPT control algorithm that minimises the maximum power point loss rate and loss time, quickly tracks the maximum power point (MPP) of the PV generator, and processes the maximum energy from the PV generator under all conditions. Energy utilisation in a PV system with MPPT controller is increased by 20 to 30% compared to the PWM charging method.
Features Highlights of the MPPT Pro DUO 30 A
Max Power-Point Tracking technology with ultra-fast tracking speed and a guaranteed tracking efficiency of at least 99.5%.
Advanced MPPT control algorithm to minimise MPP loss rate and minimise time loss.
Higher range of MPP operating voltage to improve PV module utilisation.
Possibility of limiting the charging power by user or automatic charging current (BATT-1).
Digital circuit control of adaptive three-stage charging mode to improve BATT-1 lifetime.
The product will enter power saving mode if no manual input has been made for a long time and charging conditions are not met (PV<5v).>
100% charge and discharge in the operating temperature range.
AES control signal for auto-refrigerator to avoid energy waste.
Standard Modbus protocol and RS485 communication port (5V/200mA).
Overview of the most important technical features
Maximum charging current: 30A at a battery voltage of 12V or 24V.
Optional remote display with mounting frame available.
Supports all major battery types.
Active temperature equalisation for optimal charging and ensuring long battery life.
Max. Solar power 390W at 12V system voltage and 780W at 24V system voltage.
100V max. PV input voltage
Grounding: Negative
Dimensions: 24.7cm x 16.5cm x 6.9cm (LxWxH)
Connection terminals Battery 1: 16mm² (AWG6) / Battery 2: 4mm² (AWG12)
Weight: 1,4KG
Diameter of mounting holes: 5mm
Energy consumption: 26mA at 12V / 15mA at 24V
Max. Efficiency: 98
Intelligent energy saver
If there is no manual operation for an extended period of time and charging conditions are not present, the MPPT-Pro Duo will switch to energy saving mode, reducing the unit's energy consumption to a minimum. This behaviour also reduces wear and tear on the unit, which is reflected in a significantly longer service life. The system parameters are displayed and set directly via the intuitive control panel on the controller or via the MT11 remote control (accessory).
System communication and protection functions
The refrigerator's AES control signal is built into the controller, which delivers excess solar power to the refrigerator to prevent energy waste. The protection class of the MPPT Duo is IP33. It resists splashing water and is dust-tight. Our MPPT Pro DUO has multiple protection functions, including battery overcharge protection, discharge protection and reverse polarity protection of PV and battery, which effectively ensure the safety, stability and service life of the solar system.
Scope of delivery:
1x Offgridtec 1-01-011200 MPPT DUO charge controller.
1x instruction manual
€111.84*
€93.98**
The Offgridtec MPPT Pro-Duo (MPN 1-01-011200) is an innovative high-end solar controller that was essentially designed for mobile applications. A vari...
The Multiplus-II 48/3000/35-32 gx is a high-end device combination from victron Energy (mpn pmp482306000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and the potential range of use to ess applications. The inverter module delivers a whopping 3000 w at non-linear load, or 2400 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 35 a charging power, and is complemented by a 32 a transfer switch that allows lightning-fast switching between aC connections. Compared to the rest of the series, the gx variants have an integrated gx display with numerous other connection options. important features of the Multiplus-II 48/3000/35-32 gx integrated gx control unit with various communication ports PowerControl and Powerassist -increase of mains or generator performance built-in anti-islanding function and connection for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 3000w power at non-linear load 2400 w continuous load and 6000 w peak power for 48 v battery voltage, 32 a transfer switch and 35 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/3000/35-32 gx. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. Scope of the integrated gx device A vE.Can interface This can be used to connect vE.Can devices from victron (e.g. vE.Can mppt). The port can also be reconfigured via the remote console for use with a compatible CaN bus Li-Ion battery. 1xUSB connection 1x Ethernet port 1x vE.Direct connection many possibilities for system expansion Settings can be changed within minutes using the vEConfigure software (requires a computer or laptop and MK3 USB interface).multiple monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482306000 Multiplus-II 48/3000/35-32 gx 230 v 1x instruction manual
€843.59*
€708.90**
The Multiplus-II 48/3000/35-32 gx is a high-end device combination from victron Energy (mpn pmp482306000) that combines classic Multiplus components w...
The solar module 150w mono from Offgridtec (mpn 3-01-001255) works with monocrystalline solar cells with a high efficiency of >22,3% and is ideal for 12v systems thanks to its 20v operating voltage. In Offgridtec mono solar modules only cells of the highest quality grade are installed and guarantee a constant high quality and performance with maximum service life thanks to state-of-the-art manufacturing. Features of Offgridtec 150w 12v mono solar panel proven quality directly from Offgridtec manufactured according to the latest standards monocrystalline solar cells extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v systems on land or in mobile solar systems 2 bypass diodes - minimized power loss in shaded conditions The mono 150w 12v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtecs experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. It can withstand heavy hail and storms or extreme cold and heat without any problems and thanks to the integrated bypass diodes, the module can continue to produce power even in shaded or low light conditions. The most important technical data at a glance Power (Pmax): 150w Working voltage (Vmp): 20 V Open circuit voltage (Voc): 24 V max. current (Imp): 7.5 A Short circuit current (Isc): 8.1 A max. system voltage: 1000 V permissible ambient temperature: -40°C - +85°C Dimensions: 1140 x 680 x 35 mm Weight: 12 kg Universally applicable Offgridtecs 150w 12v Mono is universally applicable for example in 12 Volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. The connection cables are 80 cm long and equipped with MC4 connectors. Scope of delivery: Offgridtec 3-01-001255 150w mono 12v solar panel
€130.78*
€109.90**
The solar module 150w mono from Offgridtec (mpn 3-01-001255) works with monocrystalline solar cells with a high efficiency of >22,3% and is ideal f...
The fsp-2 195w 12v is the second largest and newest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in the range. It has a 3-sided design and comes with a matching connection kit that allows you to quickly and easily connect to the charge controller of your choice and the battery to be charged.
Performance that sets standards
The fsp-2 195w Ultra is equipped with American SPR back-contact cells from SunPower. The look of the cells is completely black, which also gives the fsp-2 195w a very modern, high-quality look. The SPR cells ensure a very high efficiency of the panel and set new standards in this power class in combination with the low weight and compact dimensions of the fsp-2 panel.
extensive application possibilities:
excellent usable in the camping area
or for expeditions, climbing tours and much more...
for vehicles and boats without fixed solar installation ...
and numerous other applications in different areas...
technical highlights fsp-2 195w ultra foldable solar panel
Rated power: 195wp
Number of sides: 3 x 65 Wp
Module voltage (Vmp): 33,5 V
Max. Charge current (Imp): 5,82 A
Open circuit voltage (Voc): 39,4 V
Short circuit current (Isc): 6,17 A
Dimensions closed: 820 x 440 x 40 mm
Dimensions open designed: 820 x 1545 x 60 mm
Weight: 7,12 Kg
ETFE coating
SunPower high performance cells
6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side
0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller)
1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on the battery side
Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse
the included Profi-Connection Kit
The connection kit included in the scope of delivery offers everything needed for a quick start-up of the mobile solar set. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller.
For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal crocodile clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse.
customizable on request
All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred.
about the fsp-2 series
As with all Offgridtec solar module series, high quality has been emphasized in the fsp-2 series. The fsp-2 195w works with highly effective solar cells. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp-2 series is coated with ETFE coating, which provides better protection and at the same time ensures very high light transmittance. Furthermore, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions.
Scope of delivery
1x Offgridtec fsp-2 195w 12v, 3-01-012680
1x Offgridtec fsp-2 Connection-Kit
€403.23*
€338.85**
The fsp-2 195w 12v is the second largest and newest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in...
Besides a 290ml cartridge this handy Dekalin adhesive-set also includes the Dekalin Dekavator, DEKACLEAN cloths and a sheet of very fine sandpaper for an ideal preparation of the surface.
Dekasyl MS-5 is a polymer-based adhesive with a high degree of adhesion and initial strength which is ideal for elastic connections of various components.Thanks to it's adhesive power the use of clamps is mostly unnecassary. The Dekasyl MS-5 also serves as sealent between similar materials or when mechanical connections are used.
Application:
Elastic connections and sealing for trains, caravans, trucks, cars,...
Glueing windows of buses, trains, caravans,...
Glueing of edge profiles (aluminium or polyester) of trailers
Glueing of polyester components with metal frame
Characteristics:
Free of solvents, isocyanate and PVC
Very UV- and age-resistant
Very high initial strength. Very high adhesion in general even without priming on various surfaces.
Constantly elastic within a temperature range of -40°C to +120°
Neutral, odorless and quick-setting
After skim-development paintable - normally this does not influence the setting-process
Compatible with most industrial painting systems, alkyd resin paint as well as dispersion paint (because of the many different types of industrial paints a material compatibility test is recommended)
We recommend to mount our spoilers and cable entries only with Dekasyl adhesive together with DEKAvator as this connection had the best outcome in a laboratory test.
Why Dekasyl?
Manufacturers of caravans like Fendt, Dethleffs, Burstner, Carthago, Pilote and Hymer use Dekalin-products in many different areas, for example as sealent for roofs, side panels, undercoating, glueing of PMMA-windows, sound-proofing, engine-covering, and many more.As a global partner of the caravan and camping industry Dekalin provides you with a wide range of latest technology and supports sellers in realizing their demands. They offer special solutions for sealing, glueing, damming and repairing.
Details:Glue color: blackDelivery scope: 1x cartridge 290ml Dekalin 6252412 Dekasyl MS-5 adhesive black, 1x sheet of sandpaper, 1x Dekalin Dekavator 6257812 bottle 30ml, DEKACLEAN cleaning cloths
Besides a 290ml cartridge this handy Dekalin adhesive-set also includes the Dekalin Dekavator, DEKACLEAN cloths and a sheet of very fine sandpaper for...
Dieses Set enthält alles was Sie brauchen um Module mit je max. 1m Breite auf einem Ziegeldach zu befestigen. Die enthaltenen Dach-Haken sind spezielle für Ziegeldächer konstruiert. Durch hochwertigste korrosionsfreie Materialien aus Edelstahl und Aluminium ist eine sichere und langlebige Montage gewährleistet.
Die Stücklisten der Befestigungskits sind für eine Montage der Module direkt nebeneinander konzipiert. Sollten Sie z.B. zwei Reihen untereinander mit je drei Solarmodulen planen benötigen Sie zwei Kits für je drei Module.
Beinhaltet:
Dachhaken 3-fach verstellbar (Edelstahl)
Solar-Profilschienen (Aluminium)
Endklemmen (Aluminium)
Nutensteine (Aluminium)
Endkappen
Alle notwendigen Schrauben und Muttern
Hinweis:
Nur für gerahmte Module mit 30mm/35mm Rahmenstärke
Module sind nicht im Lieferumfang enthalten
Variants from €106.94*
€255.44*
€214.66**
Dieses Set enthält alles was Sie brauchen um Module mit je max. 1m Breite auf einem Ziegeldach zu befestigen. Die enthaltenen Dach-Haken sind spe...
The Autark M-Master is the medium sized complete system of the Autark family and delivers an average daily yield of 800 watt hours between March and October. The generated power is stored in the cycle-proof 122Ah agm battery - the high-quality charge controller with integrated display gives you information about the charge status of the battery while your 230v consumers can be operated at the sine wave voltage converter. Of course, the whole thing is delivered including a professional connection cable kit - plug it together and get started. The system is suitable for a wide range of applications - from 12v lighting, charging laptop, cell phone and camera batteries and other small consumers, to 230v household appliances with a maximum continuous power of 1000w (15min)
Features of the Autark M-Master
If required, module side expandable by 2 x 100w with low installation effort
Average daily yield between March and October: approx. 800wh (approx. 66Ah)
Plug & Play ready-to-connect system - plug together and go
Allows operation of 12v and 230v loads, as well as 5v usb consumers
usb charging possibility directly at the charge controller (max. 2,4A)
Easy to read lcd display informs about all operating parameters
Flexible mounting possibility thanks to 8m connection cable from module to controller
Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage shutdown, short-circuit protection, reverse polarity protection, etc.
rs485 communication port on the voltage transformer offers extensive configuration possibilities via pc (interface cable rs485 to usb included)
Charge controller enables temperature compensated charging - temperature sensor included in delivery
Configurable 12v load output at the charge controller for loads up to max. 30a - suitable e.g. for lighting control
Application areas
This complete system can be used in many ways. Whether as a stationary system on the mountain hut or in the allotment garden - the permanent operation of small coolers and refrigerators, as well as the charging of cell phones and laptops succeeds easily with this system. The installation on the motor home is also conceivable - we also have the corresponding brackets and adhesive sets for the attachment.
Extensive connection options
230v ac 50hz 1000w (15min - 1000w / permanent - 800w / short time (starting currents) - 1600w) Schuko socket on the sine wave voltage converter
12v consumer output with 30a power directly at the charge controller
2 x usb charging port at the charge controller with max. 2.4a (total)
1 x usb charging port at the voltage converter with max. 1a power
Parts list - what's inside
2 x Offgridtec 100w V2 Solarpanel 23V black frame
1 x Pair of solar connector compatible junction boxes for parallel connection of the two solar modules
1 x 30a pwm charge controller with clear lcd display and usb charging possibility - the device also has a 30a load output and is easy to operate - all important parameters can be read on the display
1 x 122Ah agm battery with m8 screw terminal Dimensions: 406 x 174 x 233 mm(+5mm terminal) - the battery is absolutely maintenance free and leak proof and lasts up to 10 years depending on use
1 x 1000w 12v to 230v sine wave voltage converter with a shockproof socket incl. connection cable - the rated power of 1000w can be output by the device for 15 minutes - beyond that the inverter outputs 800w and can handle short time starting currents up to 1600w
1 x 8m 6mm² professional connection cable solar module to charge controller with original Stäubli solar-connectors and high quality Lapp Ölflex 2x6mm² solar cable
1 x 1.5m 10mm² professional battery connection cable with MIDI fuse holder, 40a MIDI fuse and m8 ring terminals for connection between charge controller and battery
1 x Temperature sensor with 3m length for connection of the controller to the batrie
1 x 1m 25mm² connection cable from inverter to battery (included with the voltage converter)
1 x Fuse holder + 125A Mega fuse for installation between voltage transformer and battery positive pole for protection against short circuit
Roof mount for the solar module
Since there are different requirements for the mounting of a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mount as standard. This can of course be purchased additionally - find suitable suggestions here:
Solar module holder for flat roof or wall mounting
Mounting kit for pitched roof mounting on roof tiles (Frankfurter Pfanne etc.)
Mounting kit for pitched roof mounting on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure
Fastening kit for pitched roof installation on Bieberschwanz tiles
Scope of delivery:
1x Solaranlage Autark M-Master with 2x100w solar panel, 30a pwm charge controller with lcd display and usb ports, 1000w sine wave voltage converter, 122Ah agm battery, user manuals
€741.44*
€623.06**
The Autark M-Master is the medium sized complete system of the Autark family and delivers an average daily yield of 800 watt hours between March and O...
Extrem Vielseitiges Komplettpaket
Die Offgridtec® HomePremium Serie ist ein wahrer Alleskönner zu einem unschlagbaren Preis- Leistungsverhältnis. Neben der Verwendung als USV Backup Lösung mit der Auswahl zwischen Netz- und Batterievorrang, lässt sich dieses PV-System genauso gut als Eigenverbrauchsanlage verwenden. Der Leistungsfähigkeit dieser Solaranlage sind dabei kaum Grenzen gesetzt – je nach persönlichem Bedarf und auf Anfrage sind Erweiterungen, sowohl Modul- als auch akkuseitig möglich. Wird am Wechselrichter eine höhere Ausgangsleistung benötigt können hier ebenfalls weitere gleiche Geräte zur Leistungssteigerung hinzugeschalten werden.
Neben der Leistungselektronik, dem Speicher und den Solarmodulen gehören sämtliche für den Anschluss benötigten Komponenten ebenfalls zum Lieferumfang, mit Ausnahme der Solarmodulhalter, welche separat bestellt werden muss. Alle übrigen Komponenten sind Plug and Play – das bedeutet keine lästige Steckermontage oder dergleichen – anschließen und fertig. Je nach Auswahl wird das System mit oder ohne Stromzähler geliefert.
Teileliste – das ist drin
30x Luxen Solar 430W Full Black Solarmodul Luxneri Series 5
4 x 4,8kWh Pylontech US5000 LiFePo4 Speicherbatterien
1x Victron Energy MPPT SmartSolar Laderegler 450/200 48V
3x Victron PMP482505010 Multiplus-II 48/5000/70-50A
1x Cerbo GX + 1x GX Touch 50 von Victron Energy - die Kommunikationszentrale Ihres Systems
1x Victron Energy Lynx Distributor für DC Verteilung und Absicherung
1x Victron Energy Lynx Power In
3x 10m Offgridtec® Profi Verbindungskabel 6mm² Solarmodul zu Laderegler für die Verbindung zwischen Solarmodulen und Laderegler
2 x Pylontech Batterieanschlusskabelset Pylontech zu Wechselrichter 2 x 2,0m 25mm² Amphenol zu M8
1x 1m Batteriekabel 50mm² beidseitig M8 Ösen
3x 1m Batteriekabel 35mm² beidseitig M8 Ösen
3x 10m 6mm² MC-4 Verbindungskabel
1x VE.Can zu CAN-Bus BMS Type A Kabel 1.8m ASS030710018 für die Verbindung des Cerbo GX mit dem Speicher
2x 3m Victron RJ45 UTP Kabel zur Verbindung des MultiPlus mit dem Cerbo GX
3x Megasicherung 125A / 70V
1x Megasicherung 250A / 70A
2x 0,9m Victron RJ45 UTP Kabel
1x Pylontech Batterieschrank für US5000
Bei Auswahl Stromzähler:
1x Victron VM-3P75CT Energy Meter
1x Victron 5m RJ45 UTP Kabel
Erweiterte Nutzung deines HomePremium-Systems
Die Lieferung des HomePremium-Systems erfolgt wahlweise mit oder ohne Victron Stromzähler und Kabel, wobei für den Aufbau eines Energy Storage Systems jeweils zwingend ein Energiezähler mit Anschlusskabel erforderlich ist.
Mit diesem Stromzähler kannst du eine netzparallele Installation vornehmen und danach deinen Energieverbrauch überwachen, bzw. deine Energiekosten kontrollieren. Dank der Phasenkompensation könntest du sogar den 3-phasigen Zähler auch für 1-phasige Systeme nutzen. Damit sind nahtlose Integrationen von dezentralen Energiequellen und Verbrauchern in das bestehende Stromnetz kein Problem.
Luxen Solar 430W Full Black Solarmodul
Das monokristalline und bifaziale 430W Full Black Solarmodul der Series N5 von Luxen Solar überzeugt durch eine Kombination verschiedener Technologien, wie der N-TOPCon Zelltechnologie und einem 108er Halb-Zellen-Layout. Zur Leistungssteigerung wurde bei der Produktion außerdem die SMBB Half-Cut Zelltechnologie angewandt. Das hochmoderne Solarmodul repräsentiert die Spitze der Solartechnologie, indem es eine beeindruckende Leistungsausgabe und niedrige Stromgestehungskosten bietet.
Eigenschaften
Glas-Glas Modul
N-TOPCon Zelltechnologie
SMBB Half-Cut Zelltechnologie
Niedriger BOS & LCOE
Bifaziale Zellmodultechnologie
hervorragende Anti-PID und Low LID Leistung
3 Bypass-Dioden
30 Jahre Leistungsgarantie und 15 Jahre Produktgarantie
hoher Zellwirkungsgrad von über 22%
Halbzellen-Technologie
Bei der Halbzellen-Technologie ("Half-Cut") werden herkömmliche Siliziumzellen mittels eines Lasers halbiert. Die entstandenen Hälften werden danach zentral parallel geschaltet, was durch die Verringerung von Widerstandsverlusten zu einer erhöhten Leistung des Solarmoduls führt.
Bifaziale Zellen
Bifazial heißt übersetzt zweigesichtig. Und der Name ist Programm: Das Luxen Solar 430W N5 Modul ist auch auf der Rückseite mit Solarzellen ausgestattet, wodurch das Sonnenlicht noch besser aufgenommen werden kann und der Wirkungsgrad des Gesamtmoduls steigt.
Technische Daten
maximale Leistung: 430W
Modulspannung (Vmp): 32,04V
max. Strom (Imp): 13,42A
Leerlaufspannung (Voc): 38,96V
Kurzschlussstrom (Isc): 14,13A
Modulwirkungsgrad: 22,02%
Abmessungen: 1722 x 1134 x 30 mm
Betriebstemperaturbereich: -40°C bis +85°C
Zellen: 108 (6x18)
max. Betriebsspannung: 1500V DC
Gewicht: 23,5kg
LiFePo4 Speichertechnologie von Pylontech – bewährt, zuverlässig, sicher
Die US3000C Speicherbatterie von Pylontech ist eine Lithium-Eisenphosphat-Batterie der neuesten Generation, die maximale Sicherheit und Lebensdauer bietet. Jedes Modul verfügt über ein Batteriemanagementsystem (BMS) für umfassenden Schutz vor Tiefentladung, Überladung, sowie Beschädigungen durch hohe Ströme oder extreme Temperaturen. Kurzschlüsse und Verpolung sind ebenfalls ausgeschlossen.
Eigenschaften der Pylontech US3000C Speichermodule
Extrem Zyklenfest – über 6000 Zyklen bei 95% DoD (Entladung pro Zyklus)
Absolut eigensicher durch integrierte Schutzabschaltung (BMS)
Hohe Lade- und Entladeleistung von bis zu 5KW pro Modul
Hohe Speicherdichte
Geringes Eigengewicht und kompakte Bauweise
Absolut Wartungsfrei und einfach zu installieren
10 Jahre Garantie
Das Herzstück der Anlage – der Victron MultiPlus-II 48/5000
Der Multiplus-II 48/5000/70-50 von Victron Energy kombiniert klassische Multiplus-Komponenten mit einem externen Stromsensor und integrierter Anti-Islanding Funktion. Dies erweitert die Funktionen PowerControl und PowerAssist auf 100A und ermöglicht den Einsatz in ESS-Anwendungen.
Die Einstellungsmöglichkeiten am MultiPlus-II sind extrem vielfältig, ebenso wie seine Einsatzmöglichkeiten. Damit das System, so wie es geliefert wird der Bezeichnung "Plug and Play" gerecht wird, haben wir die notwendigsten Einstellungen bereits für Sie vorgenommen - das System ist somit ohne weitere Konfiguration sofort Einsatzfähig.
Leistungsmerkmale und Eigenschaften des MultiPlus-II 48/5000
PowerControl und PowerAssist – Steigerung von Netz-oder Generator-Leistung
Eingebaute Anti-Islanding-Funktion und Anschlussmöglichkeit für externen Stromsensor (optional)
Kann als Backupgerät in netzgekoppelten Anlagen eingesetzt werden
VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb
Fernüberwachung und Systemintegration
Parallel-und Drei-Phasen-Betrieb
Zugelassen nach VDE-AR-N 4105
Technische Daten
5000 W Leistung bei nicht linearer Belastung - 4000 W Dauerbelastung - 9000 W Spitzenleistung
Für 48 V Batteriespannung, 50 A Transfer-Schalter und 70A Batterieladegerät
Ausgangsspannung: 230 VAC, Frequenz: 50 Hz
Max. Wirkungsgrad: 95%
Schutzklasse IP22
Maximale Flexibilität dank zweier Wechselstromausgänge
Der MultiPlus-II bietet unterbrechungsfreien Betrieb, indem er bei Netzausfällen oder Unterbrechungen des Land-/Generatorstroms automatisch die Versorgung der Verbraucher übernimmt. Die Umschaltung erfolgt in weniger als 20 Millisekunden, um einen kontinuierlichen Betrieb von elektronischen Geräten zu gewährleisten. Ein zweiter Ausgang liefert Strom nur bei vorhandenem Wechselstrom am Eingang des MultiPlus-II. Dies ermöglicht den Anschluss von Verbrauchern wie einem Wassererhitzer, die nicht von der Batterie entladen werden sollen.
Konfiguration
Die Auslieferung des MultiPlus-II erfolgt standardmäßig unkonfiguriert. Du findest hier im Downloadbereich die Konfigurations-Anleitung für das System. Solltest du eine Vorkonfiguration durch uns wünschen, können wir dies gern gegen Aufpreis für dich übernehmen. Hierzu legest du den oben verlinkten Artikel "Offgridtec Vorkonfiguration" beim Bestellvorgang in den Warenkorb. Der Versand kann in diesem Fall 3-5 Werktage länger in Anspruch nehmen, bis die Konfiguration durchgeführt wurde.
Victron Energy Cerbo GX und GX Touch 50 – die Kommunikationszentrale deines Systems
Die neueste Entwicklung in Sachen Systemüberwachung aus dem Hause ermöglicht Ihnen die spielend einfache Kontrolle und Konfiguration deines Systems. Abgerundet durch das GXC Touch 50 – ein wasserdichtes 5 Zoll Touchscreen – behalte stets die Übersicht über deine Anlagenparameter. Durch die Funktionen des Cerbo lässt sich das System einerseits perfekt kontrollieren und überwachen, auf der anderen Seite ermöglicht es die Maximierung der Systemleistung auf noch nie da gewesene, einfache Art und Weise.
Victron Energy hat eine neue Systemüberwachung entwickelt, die dir eine einfache Kontrolle und Konfiguration ermöglicht. Das GX Touch 50, ein wasserdichter 5-Zoll-Touchscreen, bietet eine klare Übersicht über deine Anlagenparameter. Mit dem Cerbo-Modul kannst du dein System präzise überwachen und die Leistung maximieren. Es ist sowohl mit Solar-Lade-Reglern als auch mit netzgebundenen Wechselrichtern kompatibel. Montagematerial und Verbindungskabel sind im Lieferumfang enthalten. Durch die Bluetooth-Funktion des GX Touch 50 ist der Zugriff auf dein System noch schneller und einfacher. Eine optionale Wandhalterung ist verfügbar.
Victron Remote Portal
Das Victron Remote Portal (VRM) ist ein kostenloser Victron Energy Service, welcher es ermöglicht die Daten deines Systems aus der Ferne auszulesen und die Geräte entsprechend zu konfigurieren. So hast du auch bei Abwesenheit immer die volle Kontroller und Übersicht über alle relevanten Systemparameter. Die Funktionalität ist als Demoversion online verfügbar und bestens geeignet um sich einen ersten Eindruck zu verschaffen - https://vrm.victronenergy.com/landingpage
Sicherheitshinweis: Lassen Sie dieses Komplettsystem nur von einer Elektrofachkraft installieren und in Betrieb nehmen.
Variants from €16,173.02*
€0.00*
€0.00**
Extrem Vielseitiges Komplettpaket
Die Offgridtec® HomePremium Serie ist ein wahrer Alleskönner zu einem unschlagbaren Preis- Leistungsv...
The mTriple Flex l solaranlagen offer the ideal power supply for your motorhome or camper. The combination of the vbcs Triple from Votronic and the ETFE-Al solar module from Offgridtec offers a secure power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the grid in standby mode, while driving with the help of the charge booster, and the combination of solar module and MPPT charge controller in sunshine. With the device combination and the semi-flexible solar module, the total weight of the system is reduced to a minimum, ideal for mounting on a camper or motor home.
Features of the mTriple Flex l
Average daily yield of 640Wh or 1280Wh (March - October)
Permanent power supply with 3 charging options
Device combination of mains charger, charge booster and solar controller
Suitable for all common battery types (lead-acid, agm, GEl, lithium)
light & extremely flat solar module - ideal for motorhome mounting
With lCD display for monitoring the system parameters
Mounting material and cable package included
All components perfectly matched
quick and easy installation according to plug & play principle
The mTriple Flex l solaranlage contains:
Offgridtec ETFE-Al 160w 12v semi-flexible solar panel (1x or 2x depending on selection)
1x Votronic vbcs 45/30/350 Triple-CI device combination
1x Votronic 1247 Charge Control s Display
or 1x Votronic 5748 vpc Jupiter 200 combo panel
1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm white
1x Dekalin Dekasyl Ms-5 adhesive set white
1x 8m Offgridtec Connection cable from solar module to charge controller 2x6mm²
1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8
1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8
1x Offgridtec 60a 58v MIDI fuse & 1x Offgridtec 80a 58v MIDI fuse
additional for 2 modules 1x Offgridtec Branching sockets & 1x Dekalin adhesive Ms-5 white
The electronics core - the Votronic vbcs triple device combination
The vbcs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 30a you can charge your battery efficiently in standby mode from the mains. The VCC charging converter with 45a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy with the help of the MPP solar regulator for max.350Wp.The supplied temperature sensor ensures the optimal charging of your batteries.
PB mains charger:The powerful charging of the on-board battery and supply of the 12v consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even in case of large deviations of the mains supply (undervoltage/overvoltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break)
VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and severe alternator voltage fluctuations, which are common in Euro 6 vehicles. The supplied 12v consumers are protected against overvoltage and voltage fluctuations.
MPP solar controller:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solarasystem. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second.
The complete system also includes either the Charge Control s display or the vpc Jupiter 200 combination panel from Votronic. With both displays, the current output of the solarasystem can be reliably displayed, monitored and controlled. The Jupiter panel offers the additional options of a battery computer and water management.
Flexible solar supply - the Offgridtec ETFE-Al 160w solar module
The semi-flexible solar module is based on the material composition aluminum-ETFE and is equipped with highly effective monocrystalline solar cells. The superimposed ETFE layers on the front provide solid protection for the cells inside and a high light yield over many years. In addition, the modules are walkable and non-slip, making them the perfect choice for mobile applications. The AlU backing almost completely prevents cell cracking due to incorrect handling or installation. Power management is handled by five busbars, ensuring solid throughput without heat loss even at high currents.
power (Pmax): 160wp
voltage (Vmp): 18,2V
max. current (Imp): 8,80A
Short circuit current (Isc): 9,23A
max. system voltage: 200V/DC
Bendable: max. 10° (l)
Weight: 5,06kg
Dimensions: 765 x 1110 x 4 mm
Optimal cabling - Manufactured in the Offgridtec cable manufactory
The mTriple solarasystem is supplied, according to the plug & play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included.
Mounting material included
The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof feed-through creates the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules.
Individual adaptations
As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
€1,299.90*
€1,092.35**
The mTriple Flex l solaranlagen offer the ideal power supply for your motorhome or camper. The combination of the vbcs Triple from Votronic and the ET...
The mTriple Flex l solaranlagen offer the ideal power supply for your motorhome or camper. The combination of the vbcs Triple from Votronic and the ETFE-Al solar module from Offgridtec offers a secure power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the grid in standby mode, while driving with the help of the charge booster, and the combination of solar module and MPPT charge controller in sunshine. With the device combination and the semi-flexible solar module, the total weight of the system is reduced to a minimum, ideal for mounting on a camper or motor home.
Features of the mTriple Flex l
Average daily yield of 640Wh or 1280Wh (March - October)
Permanent power supply with 3 charging options
Device combination of mains charger, charge booster and solar controller
Suitable for all common battery types (lead-acid, agm, GEl, lithium)
light & extremely flat solar module - ideal for motorhome mounting
With lCD display for monitoring the system parameters
Mounting material and cable package included
All components perfectly matched
quick and easy installation according to plug & play principle
The mTriple Flex l solaranlage contains:
Offgridtec ETFE-Al 160w 12v semi-flexible solar panel (1x or 2x depending on selection)
1x Votronic vbcs 45/30/350 Triple-CI device combination
1x Votronic 1247 Charge Control s Display
or 1x Votronic 5748 vpc Jupiter 200 combo panel
1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm white
1x Dekalin Dekasyl Ms-5 adhesive set white
1x 8m Offgridtec Connection cable from solar module to charge controller 2x6mm²
1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8
1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8
1x Offgridtec 60a 58v MIDI fuse & 1x Offgridtec 80a 58v MIDI fuse
additional for 2 modules 1x Offgridtec Branching sockets & 1x Dekalin adhesive Ms-5 white
The electronics core - the Votronic vbcs triple device combination
The vbcs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 30a you can charge your battery efficiently in standby mode from the mains. The VCC charging converter with 45a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy with the help of the MPP solar regulator for max.350Wp.The supplied temperature sensor ensures the optimal charging of your batteries.
PB mains charger:The powerful charging of the on-board battery and supply of the 12v consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even in case of large deviations of the mains supply (undervoltage/overvoltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break)
VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and severe alternator voltage fluctuations, which are common in Euro 6 vehicles. The supplied 12v consumers are protected against overvoltage and voltage fluctuations.
MPP solar controller:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solarasystem. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second.
The complete system also includes either the Charge Control s display or the vpc Jupiter 200 combination panel from Votronic. With both displays, the current output of the solarasystem can be reliably displayed, monitored and controlled. The Jupiter panel offers the additional options of a battery computer and water management.
Flexible solar supply - the Offgridtec ETFE-Al 160w solar module
The semi-flexible solar module is based on the material composition aluminum-ETFE and is equipped with highly effective monocrystalline solar cells. The superimposed ETFE layers on the front provide solid protection for the cells inside and a high light yield over many years. In addition, the modules are walkable and non-slip, making them the perfect choice for mobile applications. The AlU backing almost completely prevents cell cracking due to incorrect handling or installation. Power management is handled by five busbars, ensuring solid throughput without heat loss even at high currents.
power (Pmax): 160wp
voltage (Vmp): 18,2V
max. current (Imp): 8,80A
Short circuit current (Isc): 9,23A
max. system voltage: 200V/DC
Bendable: max. 10° (l)
Weight: 5,06kg
Dimensions: 765 x 1110 x 4 mm
Optimal cabling - Manufactured in the Offgridtec cable manufactory
The mTriple solarasystem is supplied, according to the plug & play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included.
Mounting material included
The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof feed-through creates the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules.
Individual adaptations
As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
The mTriple s solarasystems offer the ideal power supply for your motorhome or camper. The combination of the VBCs Triple from Votronic and the sPR solar module from Offgridtec provides a reliable power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the mains while stationary, while driving with the help of the charge booster, and the combination of solar module and MPPT charge controller in sunshine. The compact combination of the VBCs and the highly efficient solar module is ideal when installation space is limited. The system is not only suitable for self-sufficient standing and with the framed solar panel also predestined for use on expedition vehicles.
Features of the mTriple s
Average daily yield of 480Wh resp. 960Wh (March - October)
Permanent power supply with 3 charging options
Device combination of mains charger, charge booster and solar controller
Suitable for all common battery types (lead-acid, agm, gel, lithium)
Durable framed solar module - ideal for motorhome & camper installation
With LCD display for monitoring system parameters
Mounting hardware and cable package included
All components perfectly matched
quick and easy installation according to plug & play principle
The mTriple s solaranlage contains:
Offgridtec 120w/12v sPR high power solar panel (1x or 2x depending on selection)
1x Votronic 3242 VBCs 30/20/250 Triple-CI device combination
1x Votronic 1247 Charge Control s Display
or 1x Votronic 5747 vpc Jupiter 100 Combi Panel
1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm black
1x Dekalin Dekasyl Ms-5 adhesive set black
1x 8m Offgridtec connection cable from solar module to charge controller
1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8
1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8
1x Offgridtec 40a 58v MIDI fuse & 1x Offgridtec 50a 58v MIDI fuse
additional for 2 modules 1x Offgridtec Junction box & 1x Dekalin Adhesive Ms-5 black
The electronics core - the Votronic VBCs Triple device combination
The VBCs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 20a you can charge your battery efficiently in standby mode from the mains. The VCC charge converter with 30a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy using the MPP solar regulator for max.250Wp.The supplied temperature sensor ensures the optimal charging of your batteries.
Pb mains charger:The powerful charging of the on-board battery and supply 12V consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even with large deviations of the mains supply (under/over voltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break)
VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and strong voltage fluctuations of the alternator, which are common in Euro 6 vehicles. The supplied 12V consumers are protected against overvoltage and voltage fluctuations.
MPP solar regulator:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solaranlage. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second.
The complete system also includes either the Charge Control s Display or the vpc Jupiter 100 combination panel from Votronic. Both displays can be used to reliably display, monitor and control the current output of the solaransystem. The Jupiter panel additionally offers the possibilities of a battery computer and water management.
Highly efficient solar supply - the Offgridtec sPR 120w solar module
The monocrystalline 120w sPR is a high efficiency solar panel with back contacted high performance cells delivers a very high efficiency of almost 21% . The solar panel delivers a very good energy yield, even in low light conditions and is lighter and smaller than other mono modules with the same power output. The back-contact process, where only the pure cells are visible on the front side and the black aluminum frame also provide a noble appearance and are ideal for motor homes and campers.
Power (Pmax): 120wp
voltage (Vmp): 19,8V
max. current (Imp): 6,05A
Short circuit current (Isc): 6,41A
max. system voltage: 600V/DC
Weight: 7,5 kg
Dimensions: 540 x 1055 x 35 mm
Optimal cabling - Manufactured in the Offgridtec cable manufactory
The mTriple solarasystem is supplied, in line with the plug & play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included.
Mounting material included
The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof bushing is used to create the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules.
Individual adaptations
As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
From
€1,134.29*
The mTriple s solarasystems offer the ideal power supply for your motorhome or camper. The combination of the VBCs Triple from Votronic and the sPR so...
The mTriple s solarasystems offer the ideal power supply for your motorhome or camper. The combination of the VBCs Triple from Votronic and the sPR solar module from Offgridtec provides a reliable power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the mains while stationary, while driving with the help of the charge booster, and the combination of solar module and MPPT charge controller in sunshine. The compact combination of the VBCs and the highly efficient solar module is ideal when installation space is limited. The system is not only suitable for self-sufficient standing and with the framed solar panel also predestined for use on expedition vehicles.
Features of the mTriple s
Average daily yield of 480Wh resp. 960Wh (March - October)
Permanent power supply with 3 charging options
Device combination of mains charger, charge booster and solar controller
Suitable for all common battery types (lead-acid, agm, gel, lithium)
Durable framed solar module - ideal for motorhome & camper installation
With LCD display for monitoring system parameters
Mounting hardware and cable package included
All components perfectly matched
quick and easy installation according to plug & play principle
The mTriple s solaranlage contains:
Offgridtec 120w/12v sPR high power solar panel (1x or 2x depending on selection)
1x Votronic 3242 VBCs 30/20/250 Triple-CI device combination
1x Votronic 1247 Charge Control s Display
or 1x Votronic 5747 vpc Jupiter 100 Combi Panel
1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm black
1x Dekalin Dekasyl Ms-5 adhesive set black
1x 8m Offgridtec connection cable from solar module to charge controller
1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8
1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8
1x Offgridtec 40a 58v MIDI fuse & 1x Offgridtec 50a 58v MIDI fuse
additional for 2 modules 1x Offgridtec Junction box & 1x Dekalin Adhesive Ms-5 black
The electronics core - the Votronic VBCs Triple device combination
The VBCs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 20a you can charge your battery efficiently in standby mode from the mains. The VCC charge converter with 30a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy using the MPP solar regulator for max.250Wp.The supplied temperature sensor ensures the optimal charging of your batteries.
Pb mains charger:The powerful charging of the on-board battery and supply 12V consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even with large deviations of the mains supply (under/over voltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break)
VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and strong voltage fluctuations of the alternator, which are common in Euro 6 vehicles. The supplied 12V consumers are protected against overvoltage and voltage fluctuations.
MPP solar regulator:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solaranlage. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second.
The complete system also includes either the Charge Control s Display or the vpc Jupiter 100 combination panel from Votronic. Both displays can be used to reliably display, monitor and control the current output of the solaransystem. The Jupiter panel additionally offers the possibilities of a battery computer and water management.
Highly efficient solar supply - the Offgridtec sPR 120w solar module
The monocrystalline 120w sPR is a high efficiency solar panel with back contacted high performance cells delivers a very high efficiency of almost 21% . The solar panel delivers a very good energy yield, even in low light conditions and is lighter and smaller than other mono modules with the same power output. The back-contact process, where only the pure cells are visible on the front side and the black aluminum frame also provide a noble appearance and are ideal for motor homes and campers.
Power (Pmax): 120wp
voltage (Vmp): 19,8V
max. current (Imp): 6,05A
Short circuit current (Isc): 6,41A
max. system voltage: 600V/DC
Weight: 7,5 kg
Dimensions: 540 x 1055 x 35 mm
Optimal cabling - Manufactured in the Offgridtec cable manufactory
The mTriple solarasystem is supplied, in line with the plug & play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included.
Mounting material included
The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof bushing is used to create the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules.
Individual adaptations
As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
The Offgridtec® Mobileblack series impresses with an appealing optical design in elegant black and with its extremely convincing performance parameters. Starting with the olp solar modules in the most modern shingle design and an outstanding cell efficiency of over 22%, up to the Offgridtec® mppt Pro dual charge controller, one can really speak here of a successful selection and product composition from the house Offgridtec.
155w Mobileblack l Caravan complete system
This complete system contains everything you need to charge your batteries mobile. The dual controller included in the set allows you to charge your on-board battery and the starter battery at the same time, as it has a corresponding secondary charge output. The scope of delivery includes extensive information material, in which the assembly and connection are explained step by step - this concerns both the technical connection and the bonding of the retaining spoilers and the roof duct. The grommet is made of the same material as the spoilers - the peg screw connection complies with protection class ip68 and is therefore absolutely watertight when installed correctly.
scope of delivery of the Mobileblack l 155w Caravan Solaranlage
1x Offgridtec® olp solar panel 150w V2 perc with shingle technology - 018480
1x Offgridtec abs cable gland 1-way - black with waterproof peg gland
1x Offgridtec 68cm abs mounting profiles (1pair) - for mounting the solar modules in black
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 10mm² battery connection cable with MIDI fuse holder and 40a MIDI fuse - connection cable solar charge controller to battery with battery terminals and m8 cable lug connection
1x Offgridtec® 30a mppt dual solar charge controller with auxiliary charge and aes switching output
1x remote display for mppt Pro Duo charge controller
1x Dekalin adhesive set with Dekasyl ms-5 polymer adhesive, Dekavator bonding agent, cleaning cloth and operating instructions
1x mc-4 extension cable 50cm for connecting a connection cable located on the module with the module connection cable
The Offgridtec® mppt Pro Duo 30a solar charge controller
The mppt Pro Duo controller can handle a maximum charge current of 30a. This means that this system is theoretically expandable to almost 400w solar module power - taking into account the module selection (expansion only with identical panels), an expansion of this system by a maximum of 1 module would probably make the most sense.in addition, the device has a secondary charge output via which the starter battery can be charged in parallel to the on-board battery during longer periods of standstill - a feature which is certainly very appreciated in the mobile home. So that in terms of efficiency can also be spoken of the optimum, the device also has an aes switching output - this allows in excess solar power, the automatic switching of refrigerators with "aes" from gas to 12v operation.
maximum charging current 30a - 390w module power theoretically usable
30a load output for 12v consumers directly on the charge controller
the clear remote display allows the controller to be mounted in hard-to-reach places in the vehicle without limiting the operation and overview of the system parameters
aes control signal for car refrigerator to avoid energy waste
100V maximum pv input voltage
Digital circuit control of adaptive three-stage charging mode to improve battery life
Max power point tracking technology with ultra-fast tracking speed and a guaranteed tracking efficiency of at least 99.5%
Dimensions: 24.7cm x 16.5cm x 6.9cm (lxwxh)
Weight: 1.4KG
Power consumption: 26mA at 12v
Active temperature equalization for optimal charging and ensuring long battery life
Support of all major battery types (lead acid, agm, GEl, liFePo4)
Max. Efficiency: 98%
The 150w V2 olp solar panel with the latest shingle technology
The 150w V2 olp solar module with perc technology used in the system impresses on the one hand with its unique module design with overlapping wafer arrangement (overlapping design), and on the other hand with its high module efficiency, which makes this module particularly interesting for applications on vehicles due to the limited space available.
Module voltage (Vmp): 19.4V
Max. Current (Imp): 7.74A
open circuit voltage (Voc): 22.90V
Short circuit current (Isc): 8.20A
Cell efficiency: >22%
Ambient temperature: -40°C - +85°C
Weight: 9,8KG
Dimensions: 670 x 1195 x 35mm
Protection class junction box: ip68 (waterproof)
The professional solar mounting system
Spoile profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or the like can get caught under the solar modules.
Dimensions spoiler: l x w x h: 68cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm.
The bonding
A properly executed bonding is superior to any screw connection in the hard use of motorhomes or boats. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, which would be a value calculated on the glued surface that could never be achieved with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set allows even a layman to create an absolutely solid connection between spoilers and the respective substrate.
The Dekalin adhesive set contains all the components necessary so that even the do-it-yourself installer can create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
The abs mounting profiles
Cable penetrations from the roof into the interior are always quite tricky, since it must be ensured that even after years everything is absolutely tight and also remains tight.
This is because even the slightest water ingress can lead to often irreparable damage to the interior insulation and furnishings. especially since the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed: The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures an optimal seal. Glued the bushings with the adhesive set that you also use to glue the solar mounting brackets. The housings can also be painted as desired and thus adapted to the surface on which they are to be mounted
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the mc-4 connectors.
Individual system adaptation possible on request
We strive to implement every wish of our customers in the best possible way. With the individual requirements of a Solarasystem, this is of course not always 100% possible. Therefore, if you need any customization on one of our systems just send us a mail to [email protected] - simply tell us briefly which system your request refers to, which modification you would like (e.g. additional module, color spoiler, adhesive or bushing, other charge controller, etc.) and you will receive a corresponding offer from our sales team as soon as possible. Any costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012877 Offgridtec® Mobileblack 150w 12v mppt caravan Solaranlage
€452.08*
€379.90**
The Offgridtec® Mobileblack series impresses with an appealing optical design in elegant black and with its extremely convincing performance param...
Product is expected to be back in stock on 19 April 2024
Product is expected to be back in stock on 19 April 2024
The Offgridtec® Mobileblack series impresses with an appealing optical design in elegant black and with its extremely convincing performance parameters. Starting with the olp solar modules in the most modern shingle design and an outstanding cell efficiency of over 22%, up to the Offgridtec® mppt Pro dual charge controller, one can really speak here of a successful selection and product composition from the house Offgridtec.
155w Mobileblack l Caravan complete system
This complete system contains everything you need to charge your batteries mobile. The dual controller included in the set allows you to charge your on-board battery and the starter battery at the same time, as it has a corresponding secondary charge output. The scope of delivery includes extensive information material, in which the assembly and connection are explained step by step - this concerns both the technical connection and the bonding of the retaining spoilers and the roof duct. The grommet is made of the same material as the spoilers - the peg screw connection complies with protection class ip68 and is therefore absolutely watertight when installed correctly.
scope of delivery of the Mobileblack l 155w Caravan Solaranlage
1x Offgridtec® olp solar panel 150w V2 perc with shingle technology - 018480
1x Offgridtec abs cable gland 1-way - black with waterproof peg gland
1x Offgridtec 68cm abs mounting profiles (1pair) - for mounting the solar modules in black
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 10mm² battery connection cable with MIDI fuse holder and 40a MIDI fuse - connection cable solar charge controller to battery with battery terminals and m8 cable lug connection
1x Offgridtec® 30a mppt dual solar charge controller with auxiliary charge and aes switching output
1x remote display for mppt Pro Duo charge controller
1x Dekalin adhesive set with Dekasyl ms-5 polymer adhesive, Dekavator bonding agent, cleaning cloth and operating instructions
1x mc-4 extension cable 50cm for connecting a connection cable located on the module with the module connection cable
The Offgridtec® mppt Pro Duo 30a solar charge controller
The mppt Pro Duo controller can handle a maximum charge current of 30a. This means that this system is theoretically expandable to almost 400w solar module power - taking into account the module selection (expansion only with identical panels), an expansion of this system by a maximum of 1 module would probably make the most sense.in addition, the device has a secondary charge output via which the starter battery can be charged in parallel to the on-board battery during longer periods of standstill - a feature which is certainly very appreciated in the mobile home. So that in terms of efficiency can also be spoken of the optimum, the device also has an aes switching output - this allows in excess solar power, the automatic switching of refrigerators with "aes" from gas to 12v operation.
maximum charging current 30a - 390w module power theoretically usable
30a load output for 12v consumers directly on the charge controller
the clear remote display allows the controller to be mounted in hard-to-reach places in the vehicle without limiting the operation and overview of the system parameters
aes control signal for car refrigerator to avoid energy waste
100V maximum pv input voltage
Digital circuit control of adaptive three-stage charging mode to improve battery life
Max power point tracking technology with ultra-fast tracking speed and a guaranteed tracking efficiency of at least 99.5%
Dimensions: 24.7cm x 16.5cm x 6.9cm (lxwxh)
Weight: 1.4KG
Power consumption: 26mA at 12v
Active temperature equalization for optimal charging and ensuring long battery life
Support of all major battery types (lead acid, agm, GEl, liFePo4)
Max. Efficiency: 98%
The 150w V2 olp solar panel with the latest shingle technology
The 150w V2 olp solar module with perc technology used in the system impresses on the one hand with its unique module design with overlapping wafer arrangement (overlapping design), and on the other hand with its high module efficiency, which makes this module particularly interesting for applications on vehicles due to the limited space available.
Module voltage (Vmp): 19.4V
Max. Current (Imp): 7.74A
open circuit voltage (Voc): 22.90V
Short circuit current (Isc): 8.20A
Cell efficiency: >22%
Ambient temperature: -40°C - +85°C
Weight: 9,8KG
Dimensions: 670 x 1195 x 35mm
Protection class junction box: ip68 (waterproof)
The professional solar mounting system
Spoile profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or the like can get caught under the solar modules.
Dimensions spoiler: l x w x h: 68cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm.
The bonding
A properly executed bonding is superior to any screw connection in the hard use of motorhomes or boats. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, which would be a value calculated on the glued surface that could never be achieved with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set allows even a layman to create an absolutely solid connection between spoilers and the respective substrate.
The Dekalin adhesive set contains all the components necessary so that even the do-it-yourself installer can create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
The abs mounting profiles
Cable penetrations from the roof into the interior are always quite tricky, since it must be ensured that even after years everything is absolutely tight and also remains tight.
This is because even the slightest water ingress can lead to often irreparable damage to the interior insulation and furnishings. especially since the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed: The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures an optimal seal. Glued the bushings with the adhesive set that you also use to glue the solar mounting brackets. The housings can also be painted as desired and thus adapted to the surface on which they are to be mounted
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the mc-4 connectors.
Individual system adaptation possible on request
We strive to implement every wish of our customers in the best possible way. With the individual requirements of a Solarasystem, this is of course not always 100% possible. Therefore, if you need any customization on one of our systems just send us a mail to [email protected] - simply tell us briefly which system your request refers to, which modification you would like (e.g. additional module, color spoiler, adhesive or bushing, other charge controller, etc.) and you will receive a corresponding offer from our sales team as soon as possible. Any costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012877 Offgridtec® Mobileblack 150w 12v mppt caravan Solaranlage
Product is expected to be back in stock on 19 April 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 150w sp-Ultra high-end solar module fromOffgridtec(efficiency >24%) ensure high yields. The island solar system is specially designed for motorhomes. it includes everything you need to install and start up the Solarasystem, except for the batteries. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (ebl) of the motorhome (ebl connection cable required).all components included in the set meet the highest quality standards.
special features
High-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with almost 24% far above the average
The supplied modules of the spR series are significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology for charging the on-board and starter battery for a variety of battery types
MPP tracker - maximum power point tracking ensures more yield because the entire module voltage is picked up
With lCD remote display for easy readout of key performance indicators and setting of important system parameters of the solar system
AES control signal and ebl capable - can be operated both on the Schaudt electrical block and directly on up to 2 different battery circuits
Daily yield Average daily yield in summer from May to October: 1200Wh daily (measured in the north of Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. Compare the individual prices of our included components!
The supplied components:
2x Offgridtec® 150w sp-Ultra high-end solar panel
1x Offgridtec® mppt Pro Duo charge controller 30a 12/24v for two battery circuits
1xOffgridtec® Remote display for mppt Pro Duo
1xOffgridtec 1-fold cable bushing black
2x 55cm Montage Profile schwarz, Offgridtec 006550 - heavy duty version
1x 8m Offgridtec 005095 Profi-Verbindungskabel - high quality professional version for the Womo-area
1x 1,5m Offgridtec 30a Profi-batteriekabel mit Sicherung
1x Mounting adhesive set with instructions and necessary accessories for pre-treatment
1x Solar-Y connector pair
1x ebl cable set
The set contains all components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an exra solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time, should you ever need to the surface under the solar module.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
Offgridtec® 150w sp-Ultra high end solar panel
Monocrystalline 150w Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of almost 24%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we took special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output under worse conditions is higher with the sp series than with our normal mono series.
Technical Data 150w sp-Ultra Solar Panel
power(Pmax): 150w
Voltage(Vmp): 44V
Max. Current(Imp): 3.41A
open circuit voltage(Voc): 51,79V
Short circuit current(Isc): 3,69A
Max. System voltage: 600 V/DC
Cell efficiency: >24%
Ambient temp.: -40...+85°C
Dimensions: 1320 x 550 x 35 mm
Weight: 9,37 kg
Offgridtec® mppt Pro Duo charge controller 30a 12/24v
Highly efficient dual charge controller for charging the service and starter battery. offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using MPP technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
The most important technical features of the mppt Pro Duo charge controller
Max. charge current: 30a at battery voltage of 12v or 24V
Support of all major battery types (incl. liFePO4)
Max power point tracking technology with ultra-fast tracking speed and guaranteed tracking efficiency of min. 99.5%
Active temperature equalization for optimal charging and ensuring long battery life
AES control signal for car refrigerator to avoid energy waste
Max. Solar power 380w at 12v system voltage and 780w at 24V
Max. pv input voltage: 100V
Grounding: negative
Dimensions: 247 x 165 x 69 mm
Weight: 1,4kg
Offgridtec® Display Remote display for mppt Pro Duo
The lCD remote display for the mppt Pro Duo solar charge controller enables a convenient readout of important performance figures of the solar system and furthermore the adjustment of important system parameters. The display is delivered together with a mounting frame for wall mounting.
Real-time display of operating data, operating status and error information of the connected device
Real-time data available: solar power (w), solar voltage (v), energy yield (Wh), battery voltage (v), battery charging current (A)
Possibility to set battery type and temperature directly on the remote display
Data display in graphical form on large area display
Simple and intuitive operation via 3 touch buttons on the front of the display
No external power supply necessary
Mounting & cabling
Roof spoiler mounting kit
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If the modules are mounted in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm support surface module per spoiler) x 6.5cm
Cable grommet
Cable ducts from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight. Even the slightest water ingress can often cause irreparable damage to the interior insulation and furnishings, especially as the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed:
The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing. The bushings can be glued on with the adhesive set that you also need to glue on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted.
Wiring set
All necessary cables are already pre-crimped with specialized tools. So you don't need to buy special pliers for the solar connectors. The cable has a length of 8m and accommodates 2 cores á 6mm²
The bonding
A properly executed bonding is superior to any screw connection in tough motorhome or boat use. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, this would be a value calculated on the glued surface, which could never be achieved with a screw connection in the thin aluminum or GRP carrier layer. This gluing set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The gluing set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests gladly on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. Also the color of the spoiler and the roof grommet can be changed from black to white. A short offer request with article number and change request to our customer service is sufficient (e-mail: [email protected] - Tel: +49 (0) 8721 91994-00). Please contact customer service for any costs that may be incurred.
€916.33*
€770.03**
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology c...
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 150w sp-Ultra high-end solar module fromOffgridtec(efficiency >24%) ensure high yields. The island solar system is specially designed for motorhomes. it includes everything you need to install and start up the Solarasystem, except for the batteries. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (ebl) of the motorhome (ebl connection cable required).all components included in the set meet the highest quality standards.
special features
High-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with almost 24% far above the average
The supplied modules of the spR series are significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology for charging the on-board and starter battery for a variety of battery types
MPP tracker - maximum power point tracking ensures more yield because the entire module voltage is picked up
With lCD remote display for easy readout of key performance indicators and setting of important system parameters of the solar system
AES control signal and ebl capable - can be operated both on the Schaudt electrical block and directly on up to 2 different battery circuits
Daily yield Average daily yield in summer from May to October: 1200Wh daily (measured in the north of Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. Compare the individual prices of our included components!
The supplied components:
2x Offgridtec® 150w sp-Ultra high-end solar panel
1x Offgridtec® mppt Pro Duo charge controller 30a 12/24v for two battery circuits
1xOffgridtec® Remote display for mppt Pro Duo
1xOffgridtec 1-fold cable bushing black
2x 55cm Montage Profile schwarz, Offgridtec 006550 - heavy duty version
1x 8m Offgridtec 005095 Profi-Verbindungskabel - high quality professional version for the Womo-area
1x 1,5m Offgridtec 30a Profi-batteriekabel mit Sicherung
1x Mounting adhesive set with instructions and necessary accessories for pre-treatment
1x Solar-Y connector pair
1x ebl cable set
The set contains all components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an exra solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time, should you ever need to the surface under the solar module.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
Offgridtec® 150w sp-Ultra high end solar panel
Monocrystalline 150w Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of almost 24%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we took special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output under worse conditions is higher with the sp series than with our normal mono series.
Technical Data 150w sp-Ultra Solar Panel
power(Pmax): 150w
Voltage(Vmp): 44V
Max. Current(Imp): 3.41A
open circuit voltage(Voc): 51,79V
Short circuit current(Isc): 3,69A
Max. System voltage: 600 V/DC
Cell efficiency: >24%
Ambient temp.: -40...+85°C
Dimensions: 1320 x 550 x 35 mm
Weight: 9,37 kg
Offgridtec® mppt Pro Duo charge controller 30a 12/24v
Highly efficient dual charge controller for charging the service and starter battery. offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using MPP technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
The most important technical features of the mppt Pro Duo charge controller
Max. charge current: 30a at battery voltage of 12v or 24V
Support of all major battery types (incl. liFePO4)
Max power point tracking technology with ultra-fast tracking speed and guaranteed tracking efficiency of min. 99.5%
Active temperature equalization for optimal charging and ensuring long battery life
AES control signal for car refrigerator to avoid energy waste
Max. Solar power 380w at 12v system voltage and 780w at 24V
Max. pv input voltage: 100V
Grounding: negative
Dimensions: 247 x 165 x 69 mm
Weight: 1,4kg
Offgridtec® Display Remote display for mppt Pro Duo
The lCD remote display for the mppt Pro Duo solar charge controller enables a convenient readout of important performance figures of the solar system and furthermore the adjustment of important system parameters. The display is delivered together with a mounting frame for wall mounting.
Real-time display of operating data, operating status and error information of the connected device
Real-time data available: solar power (w), solar voltage (v), energy yield (Wh), battery voltage (v), battery charging current (A)
Possibility to set battery type and temperature directly on the remote display
Data display in graphical form on large area display
Simple and intuitive operation via 3 touch buttons on the front of the display
No external power supply necessary
Mounting & cabling
Roof spoiler mounting kit
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If the modules are mounted in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm support surface module per spoiler) x 6.5cm
Cable grommet
Cable ducts from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight. Even the slightest water ingress can often cause irreparable damage to the interior insulation and furnishings, especially as the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed:
The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing. The bushings can be glued on with the adhesive set that you also need to glue on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted.
Wiring set
All necessary cables are already pre-crimped with specialized tools. So you don't need to buy special pliers for the solar connectors. The cable has a length of 8m and accommodates 2 cores á 6mm²
The bonding
A properly executed bonding is superior to any screw connection in tough motorhome or boat use. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, this would be a value calculated on the glued surface, which could never be achieved with a screw connection in the thin aluminum or GRP carrier layer. This gluing set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The gluing set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests gladly on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. Also the color of the spoiler and the roof grommet can be changed from black to white. A short offer request with article number and change request to our customer service is sufficient (e-mail: [email protected] - Tel: +49 (0) 8721 91994-00). Please contact customer service for any costs that may be incurred.
The Offgridtec® MobileBlack series impresses with its appealing visual design in elegant black and its extremely convincing performance parameters. Starting with the OLP solar modules in state-of-the-art shingle design and an outstanding cell efficiency of over 22,68%, through to the Offgridtec® MPPT Pro dual charge controller, one can truly speak of a successful selection and product composition from Offgridtec.
MobileBlack XL Caravan Complete System
This complete system contains everything you need to charge your batteries on the move. In addition to charging your on-board battery, the dual regulator included in the set also allows you to charge the starter battery at the same time, as it has a corresponding secondary charging output. The scope of delivery includes extensive information material in which the assembly and connection are explained step by step - this applies to both the technical connection and the bonding of the retaining spoiler and the roof grommet. The roof duct is probably one of the most critical points, as this is where the transition to the interior of the camper takes place. The grommet is made of the same material as the spoiler - the PEG screw connection complies with protection class IP68 and is therefore absolutely waterproof when installed correctly.
Scope of delivery of the MobileBlack XL caravan solar system
Offgridtec® OLP solar module 180W V2 with shingle technology PERC (1x or 2x depending on choice)
1x Offgridtec® 30A MPPT dual solar charge controller with auxiliary charge and AES switching Output
1x remote display for MPPT Pro Duo charge Controller
1x Offgridtec ABS cable gland 1-way - black with waterproof PEG Gland
Offgridtec 68cm ABS mounting profiles (1 pair) - for mounting the solar modules in black (1x or 2x depending on choice)
1x Offgridtec 8m 2x6mm H07RNF - connection cable solar module to solar charge controller in caravan Version
1x Offgridtec 1.5m 10mm² battery connection cable with MIDI fuse holder - connection cable solar charge controller to battery with battery terminals and M8 cable lug Connection
1x Dekalin adhesive set with Dekasyl MS-5 polymer adhesive, Dekavator bonding agent, cleaning cloth and operating instructions
40A MIDI fuse
additional for 2 modules: 1x Offgridtec MC4 branching socket & 1x Dekalin Dekasyl MS-5 polymer adhesive
The Offgridtec® MPPT Pro Duo 30A Solar Charge Controller
The MPPT Pro Duo controller can handle a maximum charge current of 30A. This means that this system can theoretically be expanded to almost 400W solar module output - however, taking into account the module selection (expansion only with identical panels), an expansion by a maximum of 1 module would probably make the most sense with this system. In addition, the unit has a secondary charging output that can be used to charge the starter battery in parallel with the on-board battery during longer periods of standing - a feature that is certainly much appreciated in the mobile home. To ensure optimum efficiency, the unit also has an AES switching output - this enables refrigerators with "AES" to be switched automatically from gas to 12 V operation in the event of surplus solar power.
maximum charging current 30A - 390W module power theoretically usable
30A load output for 12V consumers directly at the charge Controller
the clear remote display allows the controller to be mounted in hard-to-reach places in the vehicle without restricting operation and overview of the system Parameters
AES control signal for car refrigerator to avoid energy waste
100V maximum PV input voltage
Digital circuit control of adaptive three-stage charging mode to improve battery life
Max power point tracking technology with ultra-fast tracking speed and guaranteed tracking efficiency of at least 99.5%.
Dimensions: 24.7cm x 16.5cm x 6.9cm (LxWxH)
Weight: 1.4KG
Power consumption: 26mA at 12V
Active temperature equalisation for optimal charging and ensuring long battery life
Supports all major battery types (lead acid, AGM, GEL, LiFePo4)
Max. Efficiency: 98
The 180W OLP solar module with the latest shingle Technology
The 180W OLP solar module (1x or 2x depending on the selection) with PERC technology used in the system is impressive on the one hand due to its unique module design with overlapping wafer arrangement (overlapping design), and on the other hand due to its high module efficiency, which makes this module particularly interesting for applications on vehicles due to the limited space available.
Module voltage (Vmp): 23,4V
Max. Current (Imp): 7.69A
Idle voltage (Voc): 27.61V
Short-circuit current (Isc): 8.15A
cell efficiency: 22,68%
ambient temperature: -40°C - +85°C
Temperature coefficient power: -0.43%/°C
Temperature coefficient voltage: -0.34 %/°C
Temperature coefficient current: -0.05 %/°C
Weight: 10.42KG
Dimensions: 1435mm x 670mm x 35mm
Protection class junction box: IP68 (waterproof)
Length of pre-assembled connection cables: 55cm
Pre-assembled connectors: MC4 compatible connectors
The professional solar mounting system
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to neatly mounting the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoilers, no branches or similar can get caught under the solar modules.
Dimensions spoiler: L x W x H: 68cm x 8.9cm (of which approx. 3cm support surface module per spoiler) x 6.5cm.
The gluing
A properly executed gluing is superior to any screw connection in the hard use of campers or boats. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, which would be a value calculated on the glued surface that could never be achieved with a screw connection in the thin aluminium or GRP support layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The Dekalin adhesive set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included, as are detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
The ABS mounting profiles
Cable penetrations from the roof into the interior are always quite tricky, as it must be ensured that everything is absolutely tight and remains tight even after years.
After all, even the slightest ingress of water can lead to often irreparable damage to the interior insulation and furnishings. Especially since the dampness is often only noticed quite late. This is why the roof penetrations were developed: The housings are made of the same UV- and weather-resistant material as the mounting brackets offered in the online shop. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures an optimal seal. The bushings are glued with the adhesive set that you also use to glue on the solar mounting brackets. The enclosures can also be painted to match the surface on which they are to be mounted.
The professional cabling set
All necessary cables are supplied plug & play and are already pre-crimped with specialist tools. So you don't need to buy special pliers for the MC-4 connectors.
Individual system customisation possible on request
We strive to implement every wish of our customers in the best possible way. With the individual requirements of a solar system, this is of course not always 100% possible. Therefore, if you would like to have adjustments made to one of our systems, simply send us an e-mail to [email protected] - just tell us briefly which system your enquiry relates to, what change you would like (e.g. additional module, colour spoiler, adhesive or bushing, different charge controller, etc.) and you will receive an appropriate offer from our sales team as soon as possible.
Scope of delivery:
1x Offgridtec 4-01-014245-001 Offgridtec® MobileBlack XL 180W 12V MPPT Caravan Solar Power System
or
1x Offgridtec 4-01-014245-002 Offgridtec® MobileBlack XL 360W 12V MPPT Caravan Solar Power System
From
€528.90*
The Offgridtec® MobileBlack series impresses with its appealing visual design in elegant black and its extremely convincing performance parameters...
Product is expected to be back in stock on 19 April 2024
Product is expected to be back in stock on 19 April 2024
The Offgridtec® MobileBlack series impresses with its appealing visual design in elegant black and its extremely convincing performance parameters. Starting with the OLP solar modules in state-of-the-art shingle design and an outstanding cell efficiency of over 22,68%, through to the Offgridtec® MPPT Pro dual charge controller, one can truly speak of a successful selection and product composition from Offgridtec.
MobileBlack XL Caravan Complete System
This complete system contains everything you need to charge your batteries on the move. In addition to charging your on-board battery, the dual regulator included in the set also allows you to charge the starter battery at the same time, as it has a corresponding secondary charging output. The scope of delivery includes extensive information material in which the assembly and connection are explained step by step - this applies to both the technical connection and the bonding of the retaining spoiler and the roof grommet. The roof duct is probably one of the most critical points, as this is where the transition to the interior of the camper takes place. The grommet is made of the same material as the spoiler - the PEG screw connection complies with protection class IP68 and is therefore absolutely waterproof when installed correctly.
Scope of delivery of the MobileBlack XL caravan solar system
Offgridtec® OLP solar module 180W V2 with shingle technology PERC (1x or 2x depending on choice)
1x Offgridtec® 30A MPPT dual solar charge controller with auxiliary charge and AES switching Output
1x remote display for MPPT Pro Duo charge Controller
1x Offgridtec ABS cable gland 1-way - black with waterproof PEG Gland
Offgridtec 68cm ABS mounting profiles (1 pair) - for mounting the solar modules in black (1x or 2x depending on choice)
1x Offgridtec 8m 2x6mm H07RNF - connection cable solar module to solar charge controller in caravan Version
1x Offgridtec 1.5m 10mm² battery connection cable with MIDI fuse holder - connection cable solar charge controller to battery with battery terminals and M8 cable lug Connection
1x Dekalin adhesive set with Dekasyl MS-5 polymer adhesive, Dekavator bonding agent, cleaning cloth and operating instructions
40A MIDI fuse
additional for 2 modules: 1x Offgridtec MC4 branching socket & 1x Dekalin Dekasyl MS-5 polymer adhesive
The Offgridtec® MPPT Pro Duo 30A Solar Charge Controller
The MPPT Pro Duo controller can handle a maximum charge current of 30A. This means that this system can theoretically be expanded to almost 400W solar module output - however, taking into account the module selection (expansion only with identical panels), an expansion by a maximum of 1 module would probably make the most sense with this system. In addition, the unit has a secondary charging output that can be used to charge the starter battery in parallel with the on-board battery during longer periods of standing - a feature that is certainly much appreciated in the mobile home. To ensure optimum efficiency, the unit also has an AES switching output - this enables refrigerators with "AES" to be switched automatically from gas to 12 V operation in the event of surplus solar power.
maximum charging current 30A - 390W module power theoretically usable
30A load output for 12V consumers directly at the charge Controller
the clear remote display allows the controller to be mounted in hard-to-reach places in the vehicle without restricting operation and overview of the system Parameters
AES control signal for car refrigerator to avoid energy waste
100V maximum PV input voltage
Digital circuit control of adaptive three-stage charging mode to improve battery life
Max power point tracking technology with ultra-fast tracking speed and guaranteed tracking efficiency of at least 99.5%.
Dimensions: 24.7cm x 16.5cm x 6.9cm (LxWxH)
Weight: 1.4KG
Power consumption: 26mA at 12V
Active temperature equalisation for optimal charging and ensuring long battery life
Supports all major battery types (lead acid, AGM, GEL, LiFePo4)
Max. Efficiency: 98
The 180W OLP solar module with the latest shingle Technology
The 180W OLP solar module (1x or 2x depending on the selection) with PERC technology used in the system is impressive on the one hand due to its unique module design with overlapping wafer arrangement (overlapping design), and on the other hand due to its high module efficiency, which makes this module particularly interesting for applications on vehicles due to the limited space available.
Module voltage (Vmp): 23,4V
Max. Current (Imp): 7.69A
Idle voltage (Voc): 27.61V
Short-circuit current (Isc): 8.15A
cell efficiency: 22,68%
ambient temperature: -40°C - +85°C
Temperature coefficient power: -0.43%/°C
Temperature coefficient voltage: -0.34 %/°C
Temperature coefficient current: -0.05 %/°C
Weight: 10.42KG
Dimensions: 1435mm x 670mm x 35mm
Protection class junction box: IP68 (waterproof)
Length of pre-assembled connection cables: 55cm
Pre-assembled connectors: MC4 compatible connectors
The professional solar mounting system
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to neatly mounting the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoilers, no branches or similar can get caught under the solar modules.
Dimensions spoiler: L x W x H: 68cm x 8.9cm (of which approx. 3cm support surface module per spoiler) x 6.5cm.
The gluing
A properly executed gluing is superior to any screw connection in the hard use of campers or boats. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, which would be a value calculated on the glued surface that could never be achieved with a screw connection in the thin aluminium or GRP support layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The Dekalin adhesive set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included, as are detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
The ABS mounting profiles
Cable penetrations from the roof into the interior are always quite tricky, as it must be ensured that everything is absolutely tight and remains tight even after years.
After all, even the slightest ingress of water can lead to often irreparable damage to the interior insulation and furnishings. Especially since the dampness is often only noticed quite late. This is why the roof penetrations were developed: The housings are made of the same UV- and weather-resistant material as the mounting brackets offered in the online shop. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures an optimal seal. The bushings are glued with the adhesive set that you also use to glue on the solar mounting brackets. The enclosures can also be painted to match the surface on which they are to be mounted.
The professional cabling set
All necessary cables are supplied plug & play and are already pre-crimped with specialist tools. So you don't need to buy special pliers for the MC-4 connectors.
Individual system customisation possible on request
We strive to implement every wish of our customers in the best possible way. With the individual requirements of a solar system, this is of course not always 100% possible. Therefore, if you would like to have adjustments made to one of our systems, simply send us an e-mail to [email protected] - just tell us briefly which system your enquiry relates to, what change you would like (e.g. additional module, colour spoiler, adhesive or bushing, different charge controller, etc.) and you will receive an appropriate offer from our sales team as soon as possible.
Scope of delivery:
1x Offgridtec 4-01-014245-001 Offgridtec® MobileBlack XL 180W 12V MPPT Caravan Solar Power System
or
1x Offgridtec 4-01-014245-002 Offgridtec® MobileBlack XL 360W 12V MPPT Caravan Solar Power System
Product is expected to be back in stock on 19 April 2024
The mTriple Flex s solarasystems offer the ideal power supply for your motorhome or camper. The combination of the VBCs Triple from Votronic and the etfe-sPR solar module from Offgridtec offers a secure power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the mains while stationary, while driving with the help of the charge booster, and the combination of solar module and MPPT charge controller in sunshine. The compact combination of the VBCs and the highly efficient flexible solar module is ideal when installation space is limited and reduces the total weight to a minimum. The system is not only suitable for self-sufficient standing and with the flexible solar panel also predestined for use on caravan campers. Features of the mTriple Flex s Average daily yield of 440Wh or 880Wh (March - October) Permanent power supply with 3 charging options Device combination of mains charger, charge booster and solar controller Suitable for all common battery types (lead-acid, agm, gel, lithium) Lightweight & extremely flat solar module - ideal for motorhome mounting With LCD display for monitoring system parameters Mounting material and cable package included All components perfectly matched quick and easy installation according to plug & play principle The mTriple Flex s solaranlage contains: Offgridtec 110w etfe-sPR flexible solar panel (1x or 2x depending on selection) 1x Votronic 3242 VBCs 30/20/250 Triple-CI device combination 1x Votronic 1247 Charge Control s Display or 1x Votronic 5747 vpc Jupiter 100 Combi Panel 1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm white 1x Dekalin Dekasyl Ms-5 adhesive set white 1x 8m Offgridtec connection cable from solar module to charge controller 1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8 1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8 1x Offgridtec 40a 58v MIDI fuse & 1x Offgridtec 50a 58v MIDI fuse additional for 2 modules1x Offgridtec Jacks & 1x Dekalin Adhesive Ms-5 white The electronics core - the Votronic VBCs Triple device combination The VBCs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 20a you can charge your battery efficiently in standby mode from the mains. The VCC charge converter with 30a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy using the MPP solar regulator for max.250Wp.The supplied temperature sensor ensures the optimal charging of your batteries. Pb mains charger:The powerful charging of the on-board battery and supply 12V consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even with large deviations of the mains supply (under/over voltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break) VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and strong voltage fluctuations of the alternator, which are common in Euro 6 vehicles. The supplied 12V consumers are protected against overvoltage and voltage fluctuations. MPP solar controller:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solaranlage. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second. The complete system also includes either the Charge Control s Display or the vpc Jupiter 100 combination panel from Votronic. Both displays can be used to reliably display, monitor and control the current output of the solaransystem. The Jupiter panel additionally offers the possibilities of a battery computer and water management. Flexible solar supply - the Offgridtec etfe-sPR 110w solar module The semi-flexible etfe-sPR 110w solar module is a high-performance solar cell that is ideally suited for mounting on a motorhome. The module of the plastic solar glass made of etfe is slightly corrugated and can be walked on without hesitation when fully bonded, even when wet. The etfe High-Tec plastic ensures weight savings and at the same time a high light transmission of max. 96%. Power (Pmax): 110wp voltage (Vmp): 18,56V max. current (Imp): 5,97A Short circuit current (Isc): 6,34A max. system voltage: 45V/DC Bendable: up to max. 30° Weight: 2,5 kg Dimensions: 540 x 1070 x 30 mm Optimal cabling - Manufactured in the Offgridtec cable manufactory The mTriple solarasystem is supplied, in line with the plug & play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included. Mounting material included The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof bushing is used to create the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules. Individual adaptations As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
From
€899.90*
The mTriple Flex s solarasystems offer the ideal power supply for your motorhome or camper. The combination of the VBCs Triple from Votronic and the e...
The mTriple Flex s solarasystems offer the ideal power supply for your motorhome or camper. The combination of the VBCs Triple from Votronic and the etfe-sPR solar module from Offgridtec offers a secure power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the mains while stationary, while driving with the help of the charge booster, and the combination of solar module and MPPT charge controller in sunshine. The compact combination of the VBCs and the highly efficient flexible solar module is ideal when installation space is limited and reduces the total weight to a minimum. The system is not only suitable for self-sufficient standing and with the flexible solar panel also predestined for use on caravan campers. Features of the mTriple Flex s Average daily yield of 440Wh or 880Wh (March - October) Permanent power supply with 3 charging options Device combination of mains charger, charge booster and solar controller Suitable for all common battery types (lead-acid, agm, gel, lithium) Lightweight & extremely flat solar module - ideal for motorhome mounting With LCD display for monitoring system parameters Mounting material and cable package included All components perfectly matched quick and easy installation according to plug & play principle The mTriple Flex s solaranlage contains: Offgridtec 110w etfe-sPR flexible solar panel (1x or 2x depending on selection) 1x Votronic 3242 VBCs 30/20/250 Triple-CI device combination 1x Votronic 1247 Charge Control s Display or 1x Votronic 5747 vpc Jupiter 100 Combi Panel 1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm white 1x Dekalin Dekasyl Ms-5 adhesive set white 1x 8m Offgridtec connection cable from solar module to charge controller 1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8 1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8 1x Offgridtec 40a 58v MIDI fuse & 1x Offgridtec 50a 58v MIDI fuse additional for 2 modules1x Offgridtec Jacks & 1x Dekalin Adhesive Ms-5 white The electronics core - the Votronic VBCs Triple device combination The VBCs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 20a you can charge your battery efficiently in standby mode from the mains. The VCC charge converter with 30a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy using the MPP solar regulator for max.250Wp.The supplied temperature sensor ensures the optimal charging of your batteries. Pb mains charger:The powerful charging of the on-board battery and supply 12V consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even with large deviations of the mains supply (under/over voltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break) VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and strong voltage fluctuations of the alternator, which are common in Euro 6 vehicles. The supplied 12V consumers are protected against overvoltage and voltage fluctuations. MPP solar controller:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solaranlage. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second. The complete system also includes either the Charge Control s Display or the vpc Jupiter 100 combination panel from Votronic. Both displays can be used to reliably display, monitor and control the current output of the solaransystem. The Jupiter panel additionally offers the possibilities of a battery computer and water management. Flexible solar supply - the Offgridtec etfe-sPR 110w solar module The semi-flexible etfe-sPR 110w solar module is a high-performance solar cell that is ideally suited for mounting on a motorhome. The module of the plastic solar glass made of etfe is slightly corrugated and can be walked on without hesitation when fully bonded, even when wet. The etfe High-Tec plastic ensures weight savings and at the same time a high light transmission of max. 96%. Power (Pmax): 110wp voltage (Vmp): 18,56V max. current (Imp): 5,97A Short circuit current (Isc): 6,34A max. system voltage: 45V/DC Bendable: up to max. 30° Weight: 2,5 kg Dimensions: 540 x 1070 x 30 mm Optimal cabling - Manufactured in the Offgridtec cable manufactory The mTriple solarasystem is supplied, in line with the plug & play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included. Mounting material included The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof bushing is used to create the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules. Individual adaptations As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
The mTriple l solaranlagen offer the ideal power supply for your motorhome or camper. The combination of the vbcs Triple from Votronic and the OlP solar module from Offgridtec provides a reliable power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the mains while stationary, while driving with the help of the charging booster, and the combination of solar module and MPPT charge controller in sunshine.
The compact combination of the vbcs and the highly efficient solar module is ideal where installation space is limited. The system is not only suitable for stand-alone operation, and with the framed solar panel it is also predestined for use on expedition vehicles.
Features of the mTriple l:
Average daily yield of 720Wh or 1440Wh (March - October)
Permanent power supply with 3 charging options
Device combination of mains charger, charge booster and solar controller
Suitable for all common battery types (lead-acid, agm, GEl, lithium)
Resistant framed solar module - ideal for motorhome & camper mounting
With lCD display for monitoring system parameters
Mounting hardware and cable package included
All components perfectly matched
quick and easy installation according to plug & play principle
The mTriple l solaranlage contains:
Offgridtec OLP 180w V2 solar panel 23,4v with shingle technology PERC (1x or 2x depending on selection)
1x Votronic 3244 vbcs 45/30/350 Triple-CI device combination
1x Votronic 1247 Charge Control s Display
or 1x Votronic 5748 vpc Jupiter 200 combo panel
1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm black
1x Dekalin Dekasyl Ms-5 adhesive set black
1x 8m Offgridtec Connection cable from solar module to charge controller
1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8
1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8
1x Offgridtec 60a 58v MIDI fuse & 1x Offgridtec 80a 58v MIDI fuse
additional for 2 modules1x Offgridtec Jacks & 1x Dekalin Adhesive Ms-5 black
The electronics core - the Votronic vbcs triple device combination
The vbcs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 30a you can charge your battery efficiently in standby mode from the mains. The VCC charging converter with 45a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy with the help of the MPP solar regulator for max.350Wp.The supplied temperature sensor ensures the optimal charging of your batteries.
PB mains charger:The powerful charging of the on-board battery and supply of the 12v consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even in case of large deviations of the mains supply (undervoltage/overvoltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break)
VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and severe alternator voltage fluctuations, which are common in Euro 6 vehicles. The supplied 12v consumers are protected against overvoltage and voltage fluctuations.
MPP solar controller:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solarasystem. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second.
The complete system also includes either the Charge Control s display or the vpc Jupiter 200 combination panel from Votronic. With both displays, the current output of the solarasystem can be reliably displayed, monitored and controlled. The Jupiter panel offers the additional options of a battery computer and water management.
Highly efficient solar supply - the Offgridtec OlP 180w solar module
The powerful 12v OlP solar module with innovative overlapping design delivers optimal power flow through minimized power losses and significantly higher module efficiency through better space utilization. The innovative PERC technology or backside passivation provides improved absorption at longer wavelengths, e.g. at flat irradiation angles or in cloudy conditions, and the potential loss in case of partial shading is reduced. The modern, homogeneous optics without visible conductor paths perfectly round off this high-quality module.
power (Pmax): 180wp
voltage (Vmp): 23,4 V
max. current (Imp): 7,70 A
Short circuit current (Isc): 8,16 A
max. system voltage: 1000V/DC
Weight: 10,42 kg
Dimensions: 670 x 1435 x 35 mm
Optimal cabling - Manufactured in the Offgridtec cable manufactory
The mTriple solarasystem is supplied, according to the Plug & Play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included.
Mounting material included
The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof feed-through creates the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules.
Individual adaptations
As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
From
€1,315.57*
The mTriple l solaranlagen offer the ideal power supply for your motorhome or camper. The combination of the vbcs Triple from Votronic and the OlP sol...
Product is expected to be back in stock on 19 April 2024
Product is expected to be back in stock on 19 April 2024
The mTriple l solaranlagen offer the ideal power supply for your motorhome or camper. The combination of the vbcs Triple from Votronic and the OlP solar module from Offgridtec provides a reliable power supply and optimum yields. The permanent supply is ensured in three different ways. Charging from the mains while stationary, while driving with the help of the charging booster, and the combination of solar module and MPPT charge controller in sunshine.
The compact combination of the vbcs and the highly efficient solar module is ideal where installation space is limited. The system is not only suitable for stand-alone operation, and with the framed solar panel it is also predestined for use on expedition vehicles.
Features of the mTriple l:
Average daily yield of 720Wh or 1440Wh (March - October)
Permanent power supply with 3 charging options
Device combination of mains charger, charge booster and solar controller
Suitable for all common battery types (lead-acid, agm, GEl, lithium)
Resistant framed solar module - ideal for motorhome & camper mounting
With lCD display for monitoring system parameters
Mounting hardware and cable package included
All components perfectly matched
quick and easy installation according to plug & play principle
The mTriple l solaranlage contains:
Offgridtec OLP 180w V2 solar panel 23,4v with shingle technology PERC (1x or 2x depending on selection)
1x Votronic 3244 vbcs 45/30/350 Triple-CI device combination
1x Votronic 1247 Charge Control s Display
or 1x Votronic 5748 vpc Jupiter 200 combo panel
1x Offgridtec Roof bushing 1-fold for cable diameter 13mm-18mm black
1x Dekalin Dekasyl Ms-5 adhesive set black
1x 8m Offgridtec Connection cable from solar module to charge controller
1x 1,5m 10mm² Offgridtec battery cable with MIDI fuse holder - screw terminal connection on M8
1x 2.5m 10mm² Offgridtec Battery cable with MIDI fuse holder - screw terminal connection on M8
1x Offgridtec 60a 58v MIDI fuse & 1x Offgridtec 80a 58v MIDI fuse
additional for 2 modules1x Offgridtec Jacks & 1x Dekalin Adhesive Ms-5 black
The electronics core - the Votronic vbcs triple device combination
The vbcs Triple ensures your permanent power supply in three ways. With the Pb mains charger with 30a you can charge your battery efficiently in standby mode from the mains. The VCC charging converter with 45a allows you to charge your on-board battery while driving. The third option offers the charging with solar energy with the help of the MPP solar regulator for max.350Wp.The supplied temperature sensor ensures the optimal charging of your batteries.
PB mains charger:The powerful charging of the on-board battery and supply of the 12v consumers from the mains. The full charging power in the universal range of 110v/ac-230v/ac without switching is available worldwide even in case of large deviations of the mains supply (undervoltage/overvoltage, sinusoidal shape, frequency). Thanks to the long-term charging characteristics, the device can be constantly connected to the mains (operational, winter break)
VCC charge converter:The powerful charge booster allows full charging of the on-board battery while driving. It increases/decreases the voltage to the required level so that the on-board battery can be charged with the optimal charging characteristic. It fully compensates for line losses and severe alternator voltage fluctuations, which are common in Euro 6 vehicles. The supplied 12v consumers are protected against overvoltage and voltage fluctuations.
MPP solar controller:The MPP charge controller ensures a charge current gain of 10-30%, shorter charging times and the best possible power utilization of your solarasystem. The MPP technology automatically determines the maximum power output of the connected solar modules several times per second.
The complete system also includes either the Charge Control s display or the vpc Jupiter 200 combination panel from Votronic. With both displays, the current output of the solarasystem can be reliably displayed, monitored and controlled. The Jupiter panel offers the additional options of a battery computer and water management.
Highly efficient solar supply - the Offgridtec OlP 180w solar module
The powerful 12v OlP solar module with innovative overlapping design delivers optimal power flow through minimized power losses and significantly higher module efficiency through better space utilization. The innovative PERC technology or backside passivation provides improved absorption at longer wavelengths, e.g. at flat irradiation angles or in cloudy conditions, and the potential loss in case of partial shading is reduced. The modern, homogeneous optics without visible conductor paths perfectly round off this high-quality module.
power (Pmax): 180wp
voltage (Vmp): 23,4 V
max. current (Imp): 7,70 A
Short circuit current (Isc): 8,16 A
max. system voltage: 1000V/DC
Weight: 10,42 kg
Dimensions: 670 x 1435 x 35 mm
Optimal cabling - Manufactured in the Offgridtec cable manufactory
The mTriple solarasystem is supplied, according to the Plug & Play principle, with all the connecting cables required for commissioning the system. The cables are all manufactured in our own cable factory and have an optimal connection quality. The 8m long connection cable from module to charge controller allows a flexible installation, depending on the conditions on site. The battery cables have an integrated MIDI fuse holder to protect the charge controller and the technology behind it in the event of a short circuit or overcurrent. The appropriate fuses for the system are also included.
Mounting material included
The complete system is delivered with all mounting material needed to mount it on your vehicle. The Dekalin adhesive set for bonding the solar modules to the vehicle roof contains, in addition to the white power adhesive, cleaning cloths, a wool wiper and the Dekavator bonding agent. The Offgridtec roof feed-through creates the connection between the solar module on the roof and the charge controller inside the vehicle. The version with two solar modules also contains a pair of junction boxes for parallel connection of the two modules.
Individual adaptations
As with all our complete systems, individual adaptations are possible. contact us! Please ask our customer service for possible costs.
Product is expected to be back in stock on 19 April 2024
The Offgridtec mPremium+ series is a premium solar set for caravans and mobile homes. The expected daily output (April to October) is on average 1600W...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 120w sp-Ultra 12v high-end solar module fromOffgridtec(efficiency >21%) ensure high yields. The island solar system is specially designed for motorhomes. except for the batteries, it contains everything you need to install and start up the 12vSolarasystem. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (Ebl) of the motorhome. All components included in the set meet the highest quality standards.
special features
Solar generator consisting of two absolute high-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with over 21% far above average
The supplied modules of the spR series are significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology made in Germany enables charging of residential and starter battery
MPP tracker - maximum power point tracking ensures more yield because the entire module voltage is taken off
Ebl capable - can be operated both on the Schaudt electrical block and directly on up to 2 different battery circuits
if you have any questions or modification requests, our customer service will be happy to help you (e-mail: [email protected] Tel: +49 (0) 8721 7786187).
Daily yield Average daily yield in summer from May to October: 960Wh daily (measured in northern Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. compare the individual prices of our included components!
The supplied components:
2 x Offgridtec® 120w sp-Ultra 12v high end solar panel
1 x votronic MPP 250 Duo Digital Solar Charge Controller
1 x votronic lcd solar computer S
1 x cable gland (black) 1-fold - fit to the supplied cable
2 x roof spoiler set to fix the solar panels (black)
1 x 8m solar cable (2x6mm² wires in one cable) - completely ready for connection
1 x 1,5m battery cable with fuse and Ebl connection cable
1 x mounting adhesive set with instructions and necessary accessories for pre-treatment
competent help if needed included!
The set contains all the components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an exra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts many, many years....
Offgridtec® 120w sp-Ultra 12v high end solar panel
Monocrystalline 120w / 12v Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of over 21%. Here the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we have taken special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output under worse conditions is higher with the sp series than with our normal mono series.
Technical data 120w sp-Ultra 12v solar panel
- 120 Watt Maximum Power
- Maximum current(imp): 6.05A
- Voltage (vmp): 19,8v
- Short circuit current (Isc): 6,41A
- open circuit voltage (voc): 23.35v
- Dimensions; 1055 x 540 x 35 mm (HxWxD)
- Weight; 7,5 kg
The votronic MPP 250 Duo Digital Solar Charge Controller
Highly efficient dual charge controller - charges service and starter battery ! offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using MPP technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
Technical data MPP 250 Duo Digital charge controller
- Mpp - Dual - charge controller
- up to 250 Wp module power
- max. 15a module current
- max. 50 v DC module voltage
- charging options: 1 supply battery and 1 starter battery
- supported battery types: Acid, gel, agm, liFePO4
- max. charging current: battery1: 18a battery2: 1A
- Protection functions: overcharge protection, reverse current lock (night), protection against overload, overheating, reverse polarity
lcd solar computer S
clearly arranged and easy to operate at the touch of a button, the measured values are shown on the display for better control and use of the solar system. The current solar power is also always shown as a bar graph, enabling control at a glance. The display is backlit (switchable) and is very easy to read even from great distances and in all lighting conditions.
Roof spoiler mounting set
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If the modules are mounted in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm
cabling set
All necessary cables are already pre-crimped with specialized tools. So you don't need to buy special pliers for the solar connectors. The cable has a length of 8m and accommodates 2 wires á 6mm².
Cable gland
Cable penetrations from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight.
This is because even the slightest water ingress can often cause irreparable damage to interior insulation and furnishings. especially since the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed:
The housings are made of the same Uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing.
The bushings can be glued on with the adhesive set that you also need for gluing on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted.
The bonding
Properly executed bonding is superior to any screw connection in tough motorhome or boat use. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, a value that would never be attainable with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The gluing set contains all components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests gladly on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. Also the color of the spoiler and the roof grommet can be changed from black to white. A short request for quotation with article number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
€863.90*
€725.97**
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology c...
Product is expected to be back in stock on 10 April 2024
Product is expected to be back in stock on 10 April 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 120w sp-Ultra 12v high-end solar module fromOffgridtec(efficiency >21%) ensure high yields. The island solar system is specially designed for motorhomes. except for the batteries, it contains everything you need to install and start up the 12vSolarasystem. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (Ebl) of the motorhome. All components included in the set meet the highest quality standards.
special features
Solar generator consisting of two absolute high-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with over 21% far above average
The supplied modules of the spR series are significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology made in Germany enables charging of residential and starter battery
MPP tracker - maximum power point tracking ensures more yield because the entire module voltage is taken off
Ebl capable - can be operated both on the Schaudt electrical block and directly on up to 2 different battery circuits
if you have any questions or modification requests, our customer service will be happy to help you (e-mail: [email protected] Tel: +49 (0) 8721 7786187).
Daily yield Average daily yield in summer from May to October: 960Wh daily (measured in northern Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. compare the individual prices of our included components!
The supplied components:
2 x Offgridtec® 120w sp-Ultra 12v high end solar panel
1 x votronic MPP 250 Duo Digital Solar Charge Controller
1 x votronic lcd solar computer S
1 x cable gland (black) 1-fold - fit to the supplied cable
2 x roof spoiler set to fix the solar panels (black)
1 x 8m solar cable (2x6mm² wires in one cable) - completely ready for connection
1 x 1,5m battery cable with fuse and Ebl connection cable
1 x mounting adhesive set with instructions and necessary accessories for pre-treatment
competent help if needed included!
The set contains all the components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an exra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts many, many years....
Offgridtec® 120w sp-Ultra 12v high end solar panel
Monocrystalline 120w / 12v Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of over 21%. Here the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we have taken special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output under worse conditions is higher with the sp series than with our normal mono series.
Technical data 120w sp-Ultra 12v solar panel
- 120 Watt Maximum Power
- Maximum current(imp): 6.05A
- Voltage (vmp): 19,8v
- Short circuit current (Isc): 6,41A
- open circuit voltage (voc): 23.35v
- Dimensions; 1055 x 540 x 35 mm (HxWxD)
- Weight; 7,5 kg
The votronic MPP 250 Duo Digital Solar Charge Controller
Highly efficient dual charge controller - charges service and starter battery ! offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using MPP technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
Technical data MPP 250 Duo Digital charge controller
- Mpp - Dual - charge controller
- up to 250 Wp module power
- max. 15a module current
- max. 50 v DC module voltage
- charging options: 1 supply battery and 1 starter battery
- supported battery types: Acid, gel, agm, liFePO4
- max. charging current: battery1: 18a battery2: 1A
- Protection functions: overcharge protection, reverse current lock (night), protection against overload, overheating, reverse polarity
lcd solar computer S
clearly arranged and easy to operate at the touch of a button, the measured values are shown on the display for better control and use of the solar system. The current solar power is also always shown as a bar graph, enabling control at a glance. The display is backlit (switchable) and is very easy to read even from great distances and in all lighting conditions.
Roof spoiler mounting set
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If the modules are mounted in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm
cabling set
All necessary cables are already pre-crimped with specialized tools. So you don't need to buy special pliers for the solar connectors. The cable has a length of 8m and accommodates 2 wires á 6mm².
Cable gland
Cable penetrations from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight.
This is because even the slightest water ingress can often cause irreparable damage to interior insulation and furnishings. especially since the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed:
The housings are made of the same Uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing.
The bushings can be glued on with the adhesive set that you also need for gluing on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted.
The bonding
Properly executed bonding is superior to any screw connection in tough motorhome or boat use. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, a value that would never be attainable with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The gluing set contains all components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests gladly on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. Also the color of the spoiler and the roof grommet can be changed from black to white. A short request for quotation with article number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
Product is expected to be back in stock on 10 April 2024
The Offgridtec 200W Premium-L 12V (MPN 4-01-002735) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really leaves nothing to be desired. Installation takes less than two hours - practised hands are even much faster. The expected daily output (April to October) is 800 Wh/day on average (max. 1700 Wh on sunny days in Germany). The system is ideally suited for charging 12V AGM, GEL or lead-acid batteries.
200W complete motorhome set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our solar systems for motorhomes: We use an exra solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time if you need to access the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
We have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable grommet supplied is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely watertight and will last for many, many years.
Important performance features
We are the only manufacturer to offer you a complete motorhome solar system in which all components are supplied from our own production - of course, as usual, in the highest Offgridtec quality.
The Premium-Mobile system class is probably the best-selling motorhome solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again on the basis of customer experience and constantly supplemented with technical innovations.
As a customer, you therefore benefit from a product that is highly mature and reliable at a solid price.
Components of the Offgridtec 200W Premium L 12V
1x solar charge controller - 12V 30A PWM controller with display, load output, USB etc.
2x Offgridtec 100w V2 Solarpanel 23V black frame
1x Offgridtec ABS cable gland 1-fold - black with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm H07RN-F - connection cable solar module to solar charge controller in motorhome design
1x Offgridtec solar connector branching sockets
1x Offgridtec 1,5m 10mm² battery connection cable with MIDI fuse holder - connection
cable solar charge controller to battery
1x Offgridtec battery terminals (1 pair)
1 x Mounting adhesive set with instructions and necessary accessories for pre-treatment
1x MIDI fuse 40A 58V
1x Dekalin 6252212 DEKAsyl MS-5 290ml white single cartridge power adhesive
The Offgridtec PWM-PRO solar charge controller
The Offgridtec PWM-Pro 12V 30A charge controller series offers a large, convenient LCD display and works with the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. A controllable load output and 2 USB 5V outputs are also integrated in the controller and supply your 12V and 5V DC consumers with power. Please refer to the documentation of the charge controller for the complete range of functions.
The Offgridtec MONO 100W V2 Solar Panel
The MONO 100W 23V is one of over 40 proven solar panels in the Offgridtec portfolio, benefiting from Offgridtec's expertise in manufacturing high-quality 12V and 24V solar cells. Thanks to its extremely durable solar glass, the module can be used even in very adverse operating conditions. It easily withstands storms or extreme cold and heat, and with the monocrystalline PERC cells, you can expect significant yields even on cloudy days.
Technical Specifications
• Power (Pmax): 100W
• Operating Voltage (Vmp): 23.9V
• Open-Circuit Voltage (Voc): 28V
• Maximum Current (Imp): 4.2A
• Efficiency: 22.3%
• NOCT: 45+/-2°C
• Short-Circuit Current (Isc): 4.4A
• Maximum System Voltage: 1000V
• Permissible Ambient Temperature: -40°C to +85°C
• Dimensions: 925 x 560 x 35mm
• Part Number: 3-01-018385
• Weight: 6.22kg
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are supplied plug & play and are already pre-crimped with specialist tools. You therefore do not need to buy special pliers for the solar connectors.
Components of the wiring set
1x Offgridtec 8m 2x6mm H07RN-F connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of pole terminals. The cable fits M8 screw terminals or batteries with round terminals.
1x Offgridtec solar connector junction socket set - for parallel connection of the two solar modules.
Individual system adaptation possible on request
If you would like a different charge controller from our range, for example to charge board and service batteries together via solar, or if you would like the cables to have a different length, you are welcome to contact us at any time. The colour of the spoilers can also be changed from white to black. Simply send a quotation request with the item number and change request to our customer service. Any costs that may be incurred should be enquired about with customer service.
Scope of delivery:
1x Offgridtec 4-01-002735 Premium-L 200W 12V motorhome solar system with all the above-mentioned components.
1x instruction manual
€432.21*
€363.20**
The Offgridtec 200W Premium-L 12V (MPN 4-01-002735) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really ...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec 200W Premium-L 12V (MPN 4-01-002735) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really leaves nothing to be desired. Installation takes less than two hours - practised hands are even much faster. The expected daily output (April to October) is 800 Wh/day on average (max. 1700 Wh on sunny days in Germany). The system is ideally suited for charging 12V AGM, GEL or lead-acid batteries.
200W complete motorhome set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our solar systems for motorhomes: We use an exra solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time if you need to access the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
We have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable grommet supplied is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely watertight and will last for many, many years.
Important performance features
We are the only manufacturer to offer you a complete motorhome solar system in which all components are supplied from our own production - of course, as usual, in the highest Offgridtec quality.
The Premium-Mobile system class is probably the best-selling motorhome solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again on the basis of customer experience and constantly supplemented with technical innovations.
As a customer, you therefore benefit from a product that is highly mature and reliable at a solid price.
Components of the Offgridtec 200W Premium L 12V
1x solar charge controller - 12V 30A PWM controller with display, load output, USB etc.
2x Offgridtec 100w V2 Solarpanel 23V black frame
1x Offgridtec ABS cable gland 1-fold - black with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm H07RN-F - connection cable solar module to solar charge controller in motorhome design
1x Offgridtec solar connector branching sockets
1x Offgridtec 1,5m 10mm² battery connection cable with MIDI fuse holder - connection
cable solar charge controller to battery
1x Offgridtec battery terminals (1 pair)
1 x Mounting adhesive set with instructions and necessary accessories for pre-treatment
1x MIDI fuse 40A 58V
1x Dekalin 6252212 DEKAsyl MS-5 290ml white single cartridge power adhesive
The Offgridtec PWM-PRO solar charge controller
The Offgridtec PWM-Pro 12V 30A charge controller series offers a large, convenient LCD display and works with the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. A controllable load output and 2 USB 5V outputs are also integrated in the controller and supply your 12V and 5V DC consumers with power. Please refer to the documentation of the charge controller for the complete range of functions.
The Offgridtec MONO 100W V2 Solar Panel
The MONO 100W 23V is one of over 40 proven solar panels in the Offgridtec portfolio, benefiting from Offgridtec's expertise in manufacturing high-quality 12V and 24V solar cells. Thanks to its extremely durable solar glass, the module can be used even in very adverse operating conditions. It easily withstands storms or extreme cold and heat, and with the monocrystalline PERC cells, you can expect significant yields even on cloudy days.
Technical Specifications
• Power (Pmax): 100W
• Operating Voltage (Vmp): 23.9V
• Open-Circuit Voltage (Voc): 28V
• Maximum Current (Imp): 4.2A
• Efficiency: 22.3%
• NOCT: 45+/-2°C
• Short-Circuit Current (Isc): 4.4A
• Maximum System Voltage: 1000V
• Permissible Ambient Temperature: -40°C to +85°C
• Dimensions: 925 x 560 x 35mm
• Part Number: 3-01-018385
• Weight: 6.22kg
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are supplied plug & play and are already pre-crimped with specialist tools. You therefore do not need to buy special pliers for the solar connectors.
Components of the wiring set
1x Offgridtec 8m 2x6mm H07RN-F connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of pole terminals. The cable fits M8 screw terminals or batteries with round terminals.
1x Offgridtec solar connector junction socket set - for parallel connection of the two solar modules.
Individual system adaptation possible on request
If you would like a different charge controller from our range, for example to charge board and service batteries together via solar, or if you would like the cables to have a different length, you are welcome to contact us at any time. The colour of the spoilers can also be changed from white to black. Simply send a quotation request with the item number and change request to our customer service. Any costs that may be incurred should be enquired about with customer service.
Scope of delivery:
1x Offgridtec 4-01-002735 Premium-L 200W 12V motorhome solar system with all the above-mentioned components.
1x instruction manual
Product is expected to be back in stock on 29 March 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 120w sp-Ultra 12v high-end solar module fromOffgridtec(efficiency >21%) ensure high yields. The island solar system is specially designed for motorhomes. except for the batteries, it contains everything you need to install and start up the 12vSolarasystem. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (ebl) of the motorhome (ebl connection cable required).all components included in the set meet the highest quality standards.
special features
Solar generator consisting of an absolute high-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with more than 21% far above the average
The supplied module of the spR series is significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology made in Germany enables charging of residential and starter battery
mpp tracker - maximum power point tracking ensures more yield because the entire module voltage is taken off
Ebl capable - can be operated both on the Schaudt electric block and directly on up to 2 different battery circuits
Daily yield Average daily yield in summer from May to October: 480Wh daily (measured in northern Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. compare the individual prices of our included components!
The supplied components:
1x Offgridtec® 120w sp-Ultra 12v High-End Solarpanel
1x votronic mpp 165 Duo Digital Solar Charge Controller
1x votronic lcd Solarcomputer S
1x cable bushing 1-fold suitable for supplied module connection cable
1x Offgridtec 006550 55cm Montage-Profile schwarz - heavy duty version
1x8m Offgridtec 005095 professional connection cable - high quality professional version for caravans
1x 1,5m Offgridtec 005175 30a Profi-batteriekabel mit Sicherung
1x mounting glue set with instructions and necessary accessories for pre-treatment
1x Ebl cable set
The set contains all the components you need to charge your batteries on the move. The special thing about our Solarasystems for mobile homes: We use an exra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
we have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable gland supplied is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts many, many years.
Offgridtec® 120w sp-Ultra 12v high end solar panel
Monocrystalline 120w / 12v Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of more than 21%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we have taken special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. the light yield in poorer conditions is also higher in the sp series than in our normal mono series.
Technical data 120w sp-Ultra 12v solar panel
120 Watt Maximum Power
Maximum current(imp): 6.05a
Voltage (vmp): 19,8v
Short circuit current (Isc): 6,41a
open circuit voltage (voc): 23.35v
dimensions: 1055 x 540 x 35mm (HxWxD)
Weight; 7,5kg
The votronic mpp 165 Duo Digital Solar Charge Controller
Highly efficient dual charge controller - charges service and starter battery ! offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using mpp technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
Technical data mpp 165 Duo Digital charge controller
Mpp - Dual - charge controller
up to 165 Wp module power
max. 10 a module current
max. 50 v dc module voltage
charging options: 1 supply battery and 1 starter battery
supported battery types: Acid, gel, aGM, liFePO4
max. charging current: battery1: 12a battery2: 1a
Protection functions: overcharge protection, reverse current lock (night), protection against overload, overheating, reverse polarity
lcd solar computer S
the measured values are shown clearly on the display and can be easily operated at the touch of a button for better control and use of the solar system. The current solar power is also always shown as a bar graph, enabling control at a glance. The display is backlit (switchable) and is very easy to read even from great distances and in all lighting conditions.
Roof spoiler mounting set
Spoiler profiles are the first choice, especially for caravans and motor homes, when it comes to a clean mounting of the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoilers, no branches or similar can get caught under the solar modules.
spoiler dimensions: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm module contact surface per spoiler) x 6.5cm
wiring set
all necessary cables are already pre-crimped with special tools. So you don't need to buy special pliers for the mc-4 connectors. The cable has a length of 8m and accommodates 2 wires á 4mm².
Cable gland
Cable feed-throughs from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight.
Because even the smallest water ingress can lead to often irreparable damage to interior insulation and furnishings. especially since the moisture is often only noticed quite late. for this reason, the roof bushings were developed:
The housings are made of the same Uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing.
the bushings can be glued on with the adhesive set that you also need to glue on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the surface on which they are to be mounted.
The bonding
Properly executed bonding is superior to any screw connection in tough motorhome or boat applications. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, a value that would never be attainable with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The glue kit contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. the color of the spoilers and the roof grommet can also be changed from black to white. A short request for quotation with article number and change request to our customer service is sufficient. Any costs that may be incurred should be requested from customer service.
€561.55*
€471.89**
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology c...
Product is expected to be back in stock on 10 April 2024
Product is expected to be back in stock on 10 April 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 120w sp-Ultra 12v high-end solar module fromOffgridtec(efficiency >21%) ensure high yields. The island solar system is specially designed for motorhomes. except for the batteries, it contains everything you need to install and start up the 12vSolarasystem. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (ebl) of the motorhome (ebl connection cable required).all components included in the set meet the highest quality standards.
special features
Solar generator consisting of an absolute high-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with more than 21% far above the average
The supplied module of the spR series is significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology made in Germany enables charging of residential and starter battery
mpp tracker - maximum power point tracking ensures more yield because the entire module voltage is taken off
Ebl capable - can be operated both on the Schaudt electric block and directly on up to 2 different battery circuits
Daily yield Average daily yield in summer from May to October: 480Wh daily (measured in northern Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. compare the individual prices of our included components!
The supplied components:
1x Offgridtec® 120w sp-Ultra 12v High-End Solarpanel
1x votronic mpp 165 Duo Digital Solar Charge Controller
1x votronic lcd Solarcomputer S
1x cable bushing 1-fold suitable for supplied module connection cable
1x Offgridtec 006550 55cm Montage-Profile schwarz - heavy duty version
1x8m Offgridtec 005095 professional connection cable - high quality professional version for caravans
1x 1,5m Offgridtec 005175 30a Profi-batteriekabel mit Sicherung
1x mounting glue set with instructions and necessary accessories for pre-treatment
1x Ebl cable set
The set contains all the components you need to charge your batteries on the move. The special thing about our Solarasystems for mobile homes: We use an exra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
we have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable gland supplied is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts many, many years.
Offgridtec® 120w sp-Ultra 12v high end solar panel
Monocrystalline 120w / 12v Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of more than 21%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we have taken special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. the light yield in poorer conditions is also higher in the sp series than in our normal mono series.
Technical data 120w sp-Ultra 12v solar panel
120 Watt Maximum Power
Maximum current(imp): 6.05a
Voltage (vmp): 19,8v
Short circuit current (Isc): 6,41a
open circuit voltage (voc): 23.35v
dimensions: 1055 x 540 x 35mm (HxWxD)
Weight; 7,5kg
The votronic mpp 165 Duo Digital Solar Charge Controller
Highly efficient dual charge controller - charges service and starter battery ! offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using mpp technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
Technical data mpp 165 Duo Digital charge controller
Mpp - Dual - charge controller
up to 165 Wp module power
max. 10 a module current
max. 50 v dc module voltage
charging options: 1 supply battery and 1 starter battery
supported battery types: Acid, gel, aGM, liFePO4
max. charging current: battery1: 12a battery2: 1a
Protection functions: overcharge protection, reverse current lock (night), protection against overload, overheating, reverse polarity
lcd solar computer S
the measured values are shown clearly on the display and can be easily operated at the touch of a button for better control and use of the solar system. The current solar power is also always shown as a bar graph, enabling control at a glance. The display is backlit (switchable) and is very easy to read even from great distances and in all lighting conditions.
Roof spoiler mounting set
Spoiler profiles are the first choice, especially for caravans and motor homes, when it comes to a clean mounting of the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoilers, no branches or similar can get caught under the solar modules.
spoiler dimensions: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm module contact surface per spoiler) x 6.5cm
wiring set
all necessary cables are already pre-crimped with special tools. So you don't need to buy special pliers for the mc-4 connectors. The cable has a length of 8m and accommodates 2 wires á 4mm².
Cable gland
Cable feed-throughs from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight.
Because even the smallest water ingress can lead to often irreparable damage to interior insulation and furnishings. especially since the moisture is often only noticed quite late. for this reason, the roof bushings were developed:
The housings are made of the same Uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing.
the bushings can be glued on with the adhesive set that you also need to glue on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the surface on which they are to be mounted.
The bonding
Properly executed bonding is superior to any screw connection in tough motorhome or boat applications. On painted or GRP surfaces, a strength of more than 4 N/mm2 can be achieved, a value that would never be attainable with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The glue kit contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. the color of the spoilers and the roof grommet can also be changed from black to white. A short request for quotation with article number and change request to our customer service is sufficient. Any costs that may be incurred should be requested from customer service.
Product is expected to be back in stock on 10 April 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology c...
The Offgridtec® Mobileblack series impresses with an appealing optical design in elegant black and with its extremely convincing performance parameters. Starting with the olp solar modules in the most modern shingle design and an outstanding cell efficiency of over 22%, up to the Offgridtec® mppt Pro dual charge controller, one can really speak here of a successful selection and product composition from the house Offgridtec.
300W Mobileblack Caravan Complete System
This complete system contains everything you need to charge your mobile batteries. The dual controller included in the set allows you to charge your on-board battery and at the same time charge the starter battery, because it has a corresponding secondary charging output. The scope of delivery includes extensive information material, in which the assembly and connection are explained step by step - this applies to both the technical connection, as well as the bonding of the retaining spoiler and the roof gland. The grommet is made of the same material as the spoilers - the peg screw connection complies with protection class ip68 and is therefore absolutely watertight when installed correctly.
scope of delivery of the Mobileblack l 300W Caravan Solaranlage
2x Offgridtec® olp solar panel 150w V2 perc with shingle technology - 018480
1x Offgridtec abs cable gland 1-way - black with waterproof peg gland
2x Offgridtec 68cm abs mounting profiles (1pair) - for mounting the solar modules in black
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 10mm² battery connection cable with MIDI fuse holder and 40a MIDI fuse - connection cable solar charge controller to battery with battery terminals and m8 cable lug connection
1x Offgridtec® 30a mppt dual solar charge controller with auxiliary charge and aes switching output
1x remote display for mppt Pro Duo charge controller
1x Dekalin adhesive set with Dekasyl ms-5 polymer adhesive, Dekavator bonding agent, cleaning cloth and operating instructions
1x pair of solar connector junction boxes for parallel connection of the two solar modules
2x solar connector extension cable 50cm to connect a connection cable located on the module with the module connection cable
1x battery pole terminal set
1x MIDI fuse 40A 58V
The Offgridtec® mppt Pro Duo 30a solar charge controller
The mppt Pro Duo controller can handle a maximum charge current of 30a. In addition, the device has a secondary charge output through which the starter battery can be charged in parallel to the on-board battery during longer periods of standstill - a feature which is certainly very appreciated in the mobile home. So that in terms of efficiency can really be spoken of the optimum, the device also has an aes switching output - this allows in excess solar power, the automatic switching of refrigerators with "aes" from gas to 12v operation.
maximum charging current 30a
30a load output for 12v consumers directly on the charge controller
the clearly arranged remote display allows the controller to be mounted in hard-to-reach places in the vehicle without restricting the operation and overview of the system parameters
aes control signal for car refrigerator to avoid energy waste
100V maximum pv input voltage
Digital circuit control of adaptive three-stage charging mode to improve battery life
Max power point tracking technology with ultra-fast tracking speed and a guaranteed tracking efficiency of at least 99.5%
Dimensions: 24.7cm x 16.5cm x 6.9cm (lxwxh)
Weight: 1.4KG
Power consumption: 26mA at 12v
Active temperature equalization for optimal charging and ensuring long battery life
Support of all major battery types (lead acid, agm, gel, liFePo4)
Max. Efficiency: 98%
The 150w V2 olp solar panel with the latest shingle technology
The 150w V2 olp solar module with perc technology used in the system impresses on the one hand with its unique module design with overlapping wafer arrangement (overlapping design), and on the other hand with its high module efficiency, which makes this module particularly interesting for applications on vehicles due to the limited space available.
Module voltage (Vmp): 19.4V
Max. Current (Imp): 7.74A
open circuit voltage (Voc): 22.90V
Short circuit current (Isc): 8.20A
Cell efficiency: >22%
Ambient temperature: -40°C - +85°C
Weight: 9,8KG
Dimensions: 670 x 1195 x 35mm
Protection class junction box: ip68 (waterproof)
The professional solar mounting system
Spoile profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 68cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm.
The bonding
A properly executed bonding is superior to any screw connection in the hard use of motorhomes or boats. On painted or GRP surfaces, a strength of over 4 N/mm2 can be achieved. This would be a value calculated on the glued surface that could never be achieved with a screw connection in the thin aluminum or GRP support layer. This adhesive set allows even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The Dekalin gluing set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
The abs mounting profiles
Cable penetrations from the roof into the interior are always quite tricky, since it must be ensured that even after years everything is absolutely tight and also remains tight.
This is because even the slightest water ingress can lead to often irreparable damage to the interior insulation and furnishings. especially since the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed: The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures an optimal seal. The bushings are glued with the adhesive set that you also use to glue on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the solar connectors.
Individual system adaptation possible on request
We strive to implement every wish of our customers in the best possible way. With the individual requirements of a Solarasystem, this is of course not always 100% possible. Therefore, if you need any customization on one of our systems just send us a mail to [email protected] - simply tell us briefly which system your request refers to, which modification you would like (e.g. additional module, color spoiler, adhesive or bushing, other charge controller, etc.) and you will receive an appropriate offer from our sales team as soon as possible. Any costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012878 Offgridtec® Mobileblack l 300W 12v mppt Caravan Solaranlage
€654.38*
€549.90**
The Offgridtec® Mobileblack series impresses with an appealing optical design in elegant black and with its extremely convincing performance param...
Product is expected to be back in stock on 19 April 2024
Product is expected to be back in stock on 19 April 2024
The Offgridtec® Mobileblack series impresses with an appealing optical design in elegant black and with its extremely convincing performance parameters. Starting with the olp solar modules in the most modern shingle design and an outstanding cell efficiency of over 22%, up to the Offgridtec® mppt Pro dual charge controller, one can really speak here of a successful selection and product composition from the house Offgridtec.
300W Mobileblack Caravan Complete System
This complete system contains everything you need to charge your mobile batteries. The dual controller included in the set allows you to charge your on-board battery and at the same time charge the starter battery, because it has a corresponding secondary charging output. The scope of delivery includes extensive information material, in which the assembly and connection are explained step by step - this applies to both the technical connection, as well as the bonding of the retaining spoiler and the roof gland. The grommet is made of the same material as the spoilers - the peg screw connection complies with protection class ip68 and is therefore absolutely watertight when installed correctly.
scope of delivery of the Mobileblack l 300W Caravan Solaranlage
2x Offgridtec® olp solar panel 150w V2 perc with shingle technology - 018480
1x Offgridtec abs cable gland 1-way - black with waterproof peg gland
2x Offgridtec 68cm abs mounting profiles (1pair) - for mounting the solar modules in black
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 10mm² battery connection cable with MIDI fuse holder and 40a MIDI fuse - connection cable solar charge controller to battery with battery terminals and m8 cable lug connection
1x Offgridtec® 30a mppt dual solar charge controller with auxiliary charge and aes switching output
1x remote display for mppt Pro Duo charge controller
1x Dekalin adhesive set with Dekasyl ms-5 polymer adhesive, Dekavator bonding agent, cleaning cloth and operating instructions
1x pair of solar connector junction boxes for parallel connection of the two solar modules
2x solar connector extension cable 50cm to connect a connection cable located on the module with the module connection cable
1x battery pole terminal set
1x MIDI fuse 40A 58V
The Offgridtec® mppt Pro Duo 30a solar charge controller
The mppt Pro Duo controller can handle a maximum charge current of 30a. In addition, the device has a secondary charge output through which the starter battery can be charged in parallel to the on-board battery during longer periods of standstill - a feature which is certainly very appreciated in the mobile home. So that in terms of efficiency can really be spoken of the optimum, the device also has an aes switching output - this allows in excess solar power, the automatic switching of refrigerators with "aes" from gas to 12v operation.
maximum charging current 30a
30a load output for 12v consumers directly on the charge controller
the clearly arranged remote display allows the controller to be mounted in hard-to-reach places in the vehicle without restricting the operation and overview of the system parameters
aes control signal for car refrigerator to avoid energy waste
100V maximum pv input voltage
Digital circuit control of adaptive three-stage charging mode to improve battery life
Max power point tracking technology with ultra-fast tracking speed and a guaranteed tracking efficiency of at least 99.5%
Dimensions: 24.7cm x 16.5cm x 6.9cm (lxwxh)
Weight: 1.4KG
Power consumption: 26mA at 12v
Active temperature equalization for optimal charging and ensuring long battery life
Support of all major battery types (lead acid, agm, gel, liFePo4)
Max. Efficiency: 98%
The 150w V2 olp solar panel with the latest shingle technology
The 150w V2 olp solar module with perc technology used in the system impresses on the one hand with its unique module design with overlapping wafer arrangement (overlapping design), and on the other hand with its high module efficiency, which makes this module particularly interesting for applications on vehicles due to the limited space available.
Module voltage (Vmp): 19.4V
Max. Current (Imp): 7.74A
open circuit voltage (Voc): 22.90V
Short circuit current (Isc): 8.20A
Cell efficiency: >22%
Ambient temperature: -40°C - +85°C
Weight: 9,8KG
Dimensions: 670 x 1195 x 35mm
Protection class junction box: ip68 (waterproof)
The professional solar mounting system
Spoile profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If you mount the modules in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 68cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm.
The bonding
A properly executed bonding is superior to any screw connection in the hard use of motorhomes or boats. On painted or GRP surfaces, a strength of over 4 N/mm2 can be achieved. This would be a value calculated on the glued surface that could never be achieved with a screw connection in the thin aluminum or GRP support layer. This adhesive set allows even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The Dekalin gluing set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
The abs mounting profiles
Cable penetrations from the roof into the interior are always quite tricky, since it must be ensured that even after years everything is absolutely tight and also remains tight.
This is because even the slightest water ingress can lead to often irreparable damage to the interior insulation and furnishings. especially since the moisture is often not noticed until quite late. For this reason, the roof penetrations were developed: The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures an optimal seal. The bushings are glued with the adhesive set that you also use to glue on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the solar connectors.
Individual system adaptation possible on request
We strive to implement every wish of our customers in the best possible way. With the individual requirements of a Solarasystem, this is of course not always 100% possible. Therefore, if you need any customization on one of our systems just send us a mail to [email protected] - simply tell us briefly which system your request refers to, which modification you would like (e.g. additional module, color spoiler, adhesive or bushing, other charge controller, etc.) and you will receive an appropriate offer from our sales team as soon as possible. Any costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012878 Offgridtec® Mobileblack l 300W 12v mppt Caravan Solaranlage
Product is expected to be back in stock on 19 April 2024
The Offgridtec mPremium+ l-200w 12v (mpn 4-01-012420) is a premium solar kit for caravans and motor homes. The expected daily output (April to October) is 800Wh/day on average (max 1600 Wh on sunny days in Germany) and can be installed as a 12v system. Thanks to the included mppt solar charge controller, almost all common battery types such as agm, gel or modern lithium can be charged easily and mobile according to their design. The system can be conveniently analyzed and even configured from a smartphone or tablet using a free app. Since the mPremium+ series is a further development of the popular mPremium series and differs only in the charge controller used, you can look forward to system components that have been tried and tested thousands of times and will ensure a long and reliable power supply for your mobile.
200W caravan complete set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our Solarasystems for caravans: We use an extra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
scope of delivery of the mPremium+ l-200w Caravan Solaranlage
2x Offgridtec 100w 12v - monocrystalline solar module equipped with highly efficient solar cells
1x Offgridtec abs cable gland 1-way - black with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 2x6mm 15a battery connection cable - connection cable solar charge controller to battery
1x Offgridtec battery terminals (1 pair)
1x Y connector
1x Victron Energy Smart mppt 75/15 solar charge controller with bluetooth module, load output and extensive configuration options.
1x mounting adhesive set with instructions and necessary accessories for pre-treatment
competent help if needed included!
All integrated system components at a glance
The Victron SmartSolar mppt 75/15
The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 15a max. charge current for charging 12v and 24v batteries of various types. Equipped with powerful charging algorithms and a bluetooth based communication interface, the 75/15 offers all the features expected from a modern high-end charge controller:
bluetooth Smart integrated: allows setup and monitoring with a smartphone or other bluetooth enabled device.
Ultra fast maximum power point tracking (mppt).
Advanced maximum power point detection in case of partial shading.
15a load output
batterylife: intelligent battery management through load shedding.
Automatic battery voltage detection.
Flexible charging algorithms and much more.
overheating protection and load reduction at high temperatures.
The Offgridtec Mono 100w 12v Solar Panel
monocrystalline solar cells of the highest quality are used exclusively in the production of our modules. The module has a frame made of anodized aluminum and has a specially hardened ESG solar glass, which makes it particularly resistant to external influences (weather, storm, hail, etc).
The dimensions of the solar module are: 1030 x 520 x 35 mm (lxwxH).
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the solar connectors.
1x Offgridtec 8m 2x6mm h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round terminals.
1x mc4 Y-branch socket set
Individual system adaptation possible on request
If you would like to have a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. A short quote request with part number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012420 Offgridtec® mPremium+ l-200w 12v mppt Caravan Solaranlage
1x instruction manual
including all components listed above
€461.62*
€387.92**
The Offgridtec mPremium+ l-200w 12v (mpn 4-01-012420) is a premium solar kit for caravans and motor homes. The expected daily output (April to October...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec mPremium+ l-200w 12v (mpn 4-01-012420) is a premium solar kit for caravans and motor homes. The expected daily output (April to October) is 800Wh/day on average (max 1600 Wh on sunny days in Germany) and can be installed as a 12v system. Thanks to the included mppt solar charge controller, almost all common battery types such as agm, gel or modern lithium can be charged easily and mobile according to their design. The system can be conveniently analyzed and even configured from a smartphone or tablet using a free app. Since the mPremium+ series is a further development of the popular mPremium series and differs only in the charge controller used, you can look forward to system components that have been tried and tested thousands of times and will ensure a long and reliable power supply for your mobile.
200W caravan complete set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our Solarasystems for caravans: We use an extra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
scope of delivery of the mPremium+ l-200w Caravan Solaranlage
2x Offgridtec 100w 12v - monocrystalline solar module equipped with highly efficient solar cells
1x Offgridtec abs cable gland 1-way - black with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 2x6mm 15a battery connection cable - connection cable solar charge controller to battery
1x Offgridtec battery terminals (1 pair)
1x Y connector
1x Victron Energy Smart mppt 75/15 solar charge controller with bluetooth module, load output and extensive configuration options.
1x mounting adhesive set with instructions and necessary accessories for pre-treatment
competent help if needed included!
All integrated system components at a glance
The Victron SmartSolar mppt 75/15
The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 15a max. charge current for charging 12v and 24v batteries of various types. Equipped with powerful charging algorithms and a bluetooth based communication interface, the 75/15 offers all the features expected from a modern high-end charge controller:
bluetooth Smart integrated: allows setup and monitoring with a smartphone or other bluetooth enabled device.
Ultra fast maximum power point tracking (mppt).
Advanced maximum power point detection in case of partial shading.
15a load output
batterylife: intelligent battery management through load shedding.
Automatic battery voltage detection.
Flexible charging algorithms and much more.
overheating protection and load reduction at high temperatures.
The Offgridtec Mono 100w 12v Solar Panel
monocrystalline solar cells of the highest quality are used exclusively in the production of our modules. The module has a frame made of anodized aluminum and has a specially hardened ESG solar glass, which makes it particularly resistant to external influences (weather, storm, hail, etc).
The dimensions of the solar module are: 1030 x 520 x 35 mm (lxwxH).
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the solar connectors.
1x Offgridtec 8m 2x6mm h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round terminals.
1x mc4 Y-branch socket set
Individual system adaptation possible on request
If you would like to have a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. A short quote request with part number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012420 Offgridtec® mPremium+ l-200w 12v mppt Caravan Solaranlage
1x instruction manual
including all components listed above
Product is expected to be back in stock on 29 March 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 120w sp-Ultra 12v high-end solar module from Offgridtec (efficiency >21%) ensure high yields. The island solar system is specially designed for motorhomes. except for the batteries, it contains everything you need to install and start up the 12vSolarasystem. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (ebl) of the motorhome (ebl connection cable required).all components included in the set meet the highest quality standards.
special features
Solar generator consisting of three absolute high-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with almost 21% far above average
The supplied modules of the spR series are significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology made in Germany enables charging of residential and starter battery
MPP tracker - maximum power point tracking ensures more yield as the entire module voltage is taken off
Ebl capable - can be operated both on the Schaudt electrical block and directly on up to 2 different battery circuits
if you have any questions or modification requests, our customer service will be happy to help you (e-mail: [email protected] Tel: +49 (0) 8721 91994-00).
Daily yieldaverage daily yield in summer from May to October: 1440Wh daily (measured in the north of Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. Compare the individual prices of our included components!
The supplied components:
3 x Offgridtec® 120w sp-Ultra 12v high end solar panel
1 x Votronic MPP 430 Duo Digital Solar Charge Controller
1 x Votronic lcd solar computer S
1 x cable gland (black)
3 x roof spoiler set to fix the solar panels 55cm (TÜV) (black)
1 x 10m solar cable (2x10mm² wires in one cable) - completely ready for connection
1 x 1,5m battery cable with fuseand Ebl connection cable
1 x mounting adhesive set with instructions and necessary accessories for pre-treatment
2 x Solar Y-connector (branching socket) pair
4 x 50cm solar connector connection cable
competent help included if needed!
The set contains all the components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an exra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
Offgridtec® 120w sp-Ultra 12v high end solar panel
Monocrystalline 120w / 12v Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of almost 21%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we took special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output under worse conditions is higher with the sp series than with our normal mono series.
Technical data 120w sp-Ultra 12v solar panel
120 Watt Maximum power
Maximum current(Imp): 6,05A
Voltage(Vmp): 19.8V
Short circuit current (Isc): 6.41A
open circuit voltage (Voc): 23,35A
Dimensions: 1055 x 540 x 35 mm (HxWxD)
Weight; 7,5 kg
The Votronic MPP 430 Duo Digital Solar Charge Controller
Highly efficient dual charge controller - charges service and starter battery ! offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using MPP technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
Technical data MPP 430 Duo Digital charge controller
Mpp - Dual - charge controller
up to 430Wp module power
max. 26a module current
max. 50v dc module voltage
charging possibilities: 1 supply battery and 1 starter battery
supported battery types: Acid, gel, agm, liFePO4
max. charging current: battery1: 31.5a - battery2: 1A
Protection functions: overcharge protection, reverse current lock (night), protection against overload, overheating, reverse polarity
lcd solar computer S
clearly arranged and easy to operate at the touch of a button, the measured values are shown on the display for better control and use of the solar system. The current solar power is also always shown as a bar graph, enabling control at a glance. The display is backlit (switchable) and is very easy to read even from great distances and in all lighting conditions.
Roof spoiler mounting set
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If the modules are mounted in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm
Wiring kit
All necessary cables are already pre-crimped with specialized tools. So you don't need to buy special pliers for the solar connectors. The cable has a length of 10m and accommodates 2 cores á 10mm²
Cable gland
Cable penetrations from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight.
Because even the smallest water ingress can lead to often irreparable damage to interior insulation and furnishings. especially since the moisture is often noticed quite late. For this reason, the roof penetrations were developed:
The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing.
The bushings can be glued on with the adhesive set that you also need for gluing on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted.
The bonding
Properly executed bonding is superior to any screw connection in tough motorhome or boat use. On painted or GRP surfaces, a strength of over 4 N/mm2 can be achieved, a value that would never be attainable with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The gluing set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests gladly on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. Also the color of the spoiler and the roof grommet can be changed from black to white. A short request for quotation with article number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
€1,228.17*
€1,032.08**
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology c...
Product is expected to be back in stock on 10 April 2024
Product is expected to be back in stock on 10 April 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology combined with the highly efficient 120w sp-Ultra 12v high-end solar module from Offgridtec (efficiency >21%) ensure high yields. The island solar system is specially designed for motorhomes. except for the batteries, it contains everything you need to install and start up the 12vSolarasystem. Furthermore, the charge controller offers the possibility to connect the Solarasystem to the Schaudt electric block (ebl) of the motorhome (ebl connection cable required).all components included in the set meet the highest quality standards.
special features
Solar generator consisting of three absolute high-end solar modules which are equipped with American Sunpower cells and contacted on the back. The module efficiency is with almost 21% far above average
The supplied modules of the spR series are significantly smaller and lighter than comparable conventional solar modules with the same performance
Dual charge controller - innovative technology made in Germany enables charging of residential and starter battery
MPP tracker - maximum power point tracking ensures more yield as the entire module voltage is taken off
Ebl capable - can be operated both on the Schaudt electrical block and directly on up to 2 different battery circuits
if you have any questions or modification requests, our customer service will be happy to help you (e-mail: [email protected] Tel: +49 (0) 8721 91994-00).
Daily yieldaverage daily yield in summer from May to October: 1440Wh daily (measured in the north of Germany, the further south the more yield you can calculate)
With the Solar-Mobil series we rely on solid brand power and this despite the favorable conditions for our complete sets. Compare the individual prices of our included components!
The supplied components:
3 x Offgridtec® 120w sp-Ultra 12v high end solar panel
1 x Votronic MPP 430 Duo Digital Solar Charge Controller
1 x Votronic lcd solar computer S
1 x cable gland (black)
3 x roof spoiler set to fix the solar panels 55cm (TÜV) (black)
1 x 10m solar cable (2x10mm² wires in one cable) - completely ready for connection
1 x 1,5m battery cable with fuseand Ebl connection cable
1 x mounting adhesive set with instructions and necessary accessories for pre-treatment
2 x Solar Y-connector (branching socket) pair
4 x 50cm solar connector connection cable
competent help included if needed!
The set contains all the components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an exra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
Offgridtec® 120w sp-Ultra 12v high end solar panel
Monocrystalline 120w / 12v Hígh-End solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of almost 21%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we took special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output under worse conditions is higher with the sp series than with our normal mono series.
Technical data 120w sp-Ultra 12v solar panel
120 Watt Maximum power
Maximum current(Imp): 6,05A
Voltage(Vmp): 19.8V
Short circuit current (Isc): 6.41A
open circuit voltage (Voc): 23,35A
Dimensions: 1055 x 540 x 35 mm (HxWxD)
Weight; 7,5 kg
The Votronic MPP 430 Duo Digital Solar Charge Controller
Highly efficient dual charge controller - charges service and starter battery ! offers the possibility to connect the photovoltaic system to the electric block of the motorhome. Using MPP technology, the controller automatically determines the maximum power output (mpp) of the solar modules several times per second. It then converts the voltage surplus of the solar module into a higher charging current for the battery. A special high-frequency switching controller technology with high efficiency makes this possible and thus ensures shorter charging times and the best possible power utilization of the Solarasystem.
Technical data MPP 430 Duo Digital charge controller
Mpp - Dual - charge controller
up to 430Wp module power
max. 26a module current
max. 50v dc module voltage
charging possibilities: 1 supply battery and 1 starter battery
supported battery types: Acid, gel, agm, liFePO4
max. charging current: battery1: 31.5a - battery2: 1A
Protection functions: overcharge protection, reverse current lock (night), protection against overload, overheating, reverse polarity
lcd solar computer S
clearly arranged and easy to operate at the touch of a button, the measured values are shown on the display for better control and use of the solar system. The current solar power is also always shown as a bar graph, enabling control at a glance. The display is backlit (switchable) and is very easy to read even from great distances and in all lighting conditions.
Roof spoiler mounting set
Spoiler profiles are the first choice especially for caravans and motorhomes when it comes to a clean mounting of the solar modules. If the modules are mounted in the direction of travel, wind noise is no longer an issue (this also applies to alcove vehicles). Due to the closed construction of the spoiler, no branches or similar can get caught under the solar modules.
Dimensions spoiler: l x w x h: 54.5cm x 8.9cm (of which approx. 3cm bearing surface module per spoiler) x 6.5cm
Wiring kit
All necessary cables are already pre-crimped with specialized tools. So you don't need to buy special pliers for the solar connectors. The cable has a length of 10m and accommodates 2 cores á 10mm²
Cable gland
Cable penetrations from the roof into the interior are always quite tricky, because it must be ensured that even after years everything is absolutely tight and also remains tight.
Because even the smallest water ingress can lead to often irreparable damage to interior insulation and furnishings. especially since the moisture is often noticed quite late. For this reason, the roof penetrations were developed:
The housings are made of the same uv- and weather-resistant material as the mounting brackets offered in the online store. They are extremely stable and absolutely slip-proof. The wide adhesive edge ensures optimum sealing.
The bushings can be glued on with the adhesive set that you also need for gluing on the solar mounting brackets. The housings can also be painted as desired and thus adapted to the substrate on which they are to be mounted.
The bonding
Properly executed bonding is superior to any screw connection in tough motorhome or boat use. On painted or GRP surfaces, a strength of over 4 N/mm2 can be achieved, a value that would never be attainable with a screw connection in the thin aluminum or GRP carrier layer. This adhesive set enables even a layman to create an absolutely firm connection between spoilers and the respective substrate.
The gluing set contains all the components necessary for even the do-it-yourself installer to create a professional connection. Stainless steel screws for fastening the solar modules are included as well as detailed bonding instructions. In addition, all you need is a standard hand lever press for cartridges and a lint-free cloth.
Individual change requests gladly on request
If you would like a different charge controller from our range, or if the cables should have a different length, you are welcome to contact us at any time. Also the color of the spoiler and the roof grommet can be changed from black to white. A short request for quotation with article number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
Product is expected to be back in stock on 10 April 2024
The Offgridtec mPremium+ l-100w 12v (mpn 4-01-012415) is a premium solar kit for caravans and motor homes. The expected daily output (April to October) is 400Wh/day on average (max 800 Wh on sunny days in Germany) and can be installed as a 12v system. Thanks to the included mppt solar charge controller, almost all common battery types such as agm, gel or modern lithium can be charged easily and mobile according to their design. The system can be conveniently analyzed and even configured from a smartphone or tablet using a free app. Since the mPremium+ series is a further development of the popular mPremium series and differs only in the charge controller used, you can look forward to system components that have been tried and tested thousands of times and will ensure a long and reliable power supply for your mobile.
100w caravan complete set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our Solarasystems for caravans: We use an extra solid mounting system that can be easily glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
scope of delivery of the mPremium+ l 100w caravan Solaranlage
1x Offgridtec 100w 12v - monocrystalline solar module equipped with high efficiency solar cells
1x Offgridtec abs cable gland 1-fold - black with waterproof PEG gland
1x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 2x6mm 15a battery connection cable - connection cable solar charge controller to battery, 20a fuse and pole terminals
1x Victron Energy Smart mppt 75/15 solar charge controller with bluetooth module, load output and extensive configuration options.
1x Mounting adhesive set with instructions and necessary accessories for pre-treatment
All integrated system components at a glance
The Victron SmartSolar mppt 75/15
The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 20a max. charge current for charging 12v and 24v batteries of various types. Equipped with powerful charging algorithms and a bluetooth based communication interface, the 75/15 offers all the features expected from a modern high-end charge controller:
bluetooth Smart integrated: allows setup and monitoring with a smartphone or other bluetooth enabled device.
Ultra fast maximum power point tracking (mppt).
Advanced maximum power point detection in case of partial shading.
15a load output.
batterylife: intelligent battery management through load shedding.
Automatic battery voltage detection.
Flexible charging algorithms and much more.
overheating protection and load reduction at high temperatures.
The Offgridtec 100w 12v solar panel
monocrystalline solar cells of the highest quality are used exclusively in the production of our modules. The module has a frame made of anodized aluminum and has a specially hardened ESG solar glass, which makes it particularly resistant to external influences (weather, storm, hail, etc).
The dimensions of the solar module are: 1030 x 520 x 35 mm (lxwxH).
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: white
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the mc-4 connectors.
1x Offgridtec 8m 2x6mm h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round terminals.
Individual system customization possible on request
If you want a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. A short quote request with part number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012415 Offgridtec® mPremium+ l 100w 12v mppt Caravan Solaranlage
1x instruction manual
including all components listed above
€315.52*
€265.14**
The Offgridtec mPremium+ l-100w 12v (mpn 4-01-012415) is a premium solar kit for caravans and motor homes. The expected daily output (April to October...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec mPremium+ l-100w 12v (mpn 4-01-012415) is a premium solar kit for caravans and motor homes. The expected daily output (April to October) is 400Wh/day on average (max 800 Wh on sunny days in Germany) and can be installed as a 12v system. Thanks to the included mppt solar charge controller, almost all common battery types such as agm, gel or modern lithium can be charged easily and mobile according to their design. The system can be conveniently analyzed and even configured from a smartphone or tablet using a free app. Since the mPremium+ series is a further development of the popular mPremium series and differs only in the charge controller used, you can look forward to system components that have been tried and tested thousands of times and will ensure a long and reliable power supply for your mobile.
100w caravan complete set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our Solarasystems for caravans: We use an extra solid mounting system that can be easily glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
scope of delivery of the mPremium+ l 100w caravan Solaranlage
1x Offgridtec 100w 12v - monocrystalline solar module equipped with high efficiency solar cells
1x Offgridtec abs cable gland 1-fold - black with waterproof PEG gland
1x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 2x6mm 15a battery connection cable - connection cable solar charge controller to battery, 20a fuse and pole terminals
1x Victron Energy Smart mppt 75/15 solar charge controller with bluetooth module, load output and extensive configuration options.
1x Mounting adhesive set with instructions and necessary accessories for pre-treatment
All integrated system components at a glance
The Victron SmartSolar mppt 75/15
The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 20a max. charge current for charging 12v and 24v batteries of various types. Equipped with powerful charging algorithms and a bluetooth based communication interface, the 75/15 offers all the features expected from a modern high-end charge controller:
bluetooth Smart integrated: allows setup and monitoring with a smartphone or other bluetooth enabled device.
Ultra fast maximum power point tracking (mppt).
Advanced maximum power point detection in case of partial shading.
15a load output.
batterylife: intelligent battery management through load shedding.
Automatic battery voltage detection.
Flexible charging algorithms and much more.
overheating protection and load reduction at high temperatures.
The Offgridtec 100w 12v solar panel
monocrystalline solar cells of the highest quality are used exclusively in the production of our modules. The module has a frame made of anodized aluminum and has a specially hardened ESG solar glass, which makes it particularly resistant to external influences (weather, storm, hail, etc).
The dimensions of the solar module are: 1030 x 520 x 35 mm (lxwxH).
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: white
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the mc-4 connectors.
1x Offgridtec 8m 2x6mm h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round terminals.
Individual system customization possible on request
If you want a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. A short quote request with part number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-012415 Offgridtec® mPremium+ l 100w 12v mppt Caravan Solaranlage
1x instruction manual
including all components listed above
Product is expected to be back in stock on 29 March 2024
This solar set for self-sufficient power supply in a motorhome really leaves nothing to be desired. Innovative Mpp dual charge controller technology c...
The Offgridtec 150W Premium-L 12V (MPN 4-01-007500) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really leaves nothing to be desired. Installation takes less than two hours - practised hands are much quicker still. The expected daily output (April to October) is 600Wh/day on average (max. 1200 Wh on sunny days in Germany). The system is ideally suited for charging 12V AGM, GEL or lead-acid batteries.
150W complete motorhome set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our solar systems for motorhomes: We use an exra solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time if you need to access the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
We have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable grommet supplied is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely watertight and will last for many, many years.
Important performance features
We are the only manufacturer to offer you a complete motorhome solar system in which all components are supplied from our own production - of course, as usual, in the highest Offgridtec quality.
The Premium-Mobile system class is probably the best-selling motorhome solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again on the basis of customer experience and constantly supplemented with technical innovations.
As a customer, you therefore benefit from a product that is highly mature and reliable at a solid price.
Components of the Offgridtec 150W Premium L 12V
1x Offgridtec PWM-Pro12/24-30 PWM Solar Charge Controller - 12V 30A PWM controller with display, load output, USB and more
1x Offgridtec 150W MONO V2 - monocrystalline solar module 018395
1x Offgridtec ABS cable entry 1-fold - black with waterproof PEG gland
1x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec Connection cable solar module to solar charge controller in motorhome design
1x Offgridtec 1,5m 10mm² Battery connection cable with MIDI fuse holder - Solar charge controller to battery connection cable
1x Offgridtec Battery poles clamps (1 pair)
1x Assembly adhesive set with instructions and necessary accessories for pre-treatment
1x MIDI fuse 40A 58V
The Offgridtec PWM-PRO 12/24-30 Solar Charge Controller
The Offgridtec PWM-Pro 12/24 charge controller series offers a large, convenient LCD display and works with the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. A controllable load output and 2 USB 5V outputs are also integrated into the controller and supply your 12V and 5V DC consumers with power. Please refer to the documentation of the charge controller for the complete range of functions.
The Offgridtec 150W MONO V2 solar panel
Only monocrystalline solar cells of the highest quality are used in the production of our modules. The module has a frame made of anodised aluminium and has specially hardened ESG solar glass, which makes it particularly resistant to external influences (weathering, etc.).
The expected daily output (April to October): 600Wh/day on average (max. 1200 Wh on sunny days in Germany).
Solar module dimensions: 1350 x 590 x 35 mm
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are supplied plug & play and are already pre-crimped with specialist tools. So you do not need to buy special pliers for the MC-4 connectors.
Components of the wiring set
1x Offgridtec 8m 2x6mm H07RN-F connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of pole terminals. The cable fits M8 screw terminals or batteries with round terminals.
Individual system adaptation possible on request
If you would like a different charge controller from our range, for example to charge board and service batteries together via solar, or if you would like the cables to have a different length, you are welcome to contact us at any time. The colour of the spoilers can also be changed from white to black. A short request for quotation with article number and change request to our customer service is sufficient. Any costs that may be incurred should be enquired about with our customer service.
Scope of delivery:
1x Offgridtec 4-01-007500 Premium-L 150W 12V motorhome solar system with all the above components
1x instruction manual
€332.01*
€279.00**
The Offgridtec 150W Premium-L 12V (MPN 4-01-007500) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really ...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec 150W Premium-L 12V (MPN 4-01-007500) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really leaves nothing to be desired. Installation takes less than two hours - practised hands are much quicker still. The expected daily output (April to October) is 600Wh/day on average (max. 1200 Wh on sunny days in Germany). The system is ideally suited for charging 12V AGM, GEL or lead-acid batteries.
150W complete motorhome set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our solar systems for motorhomes: We use an exra solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time if you need to access the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
We have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable grommet supplied is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely watertight and will last for many, many years.
Important performance features
We are the only manufacturer to offer you a complete motorhome solar system in which all components are supplied from our own production - of course, as usual, in the highest Offgridtec quality.
The Premium-Mobile system class is probably the best-selling motorhome solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again on the basis of customer experience and constantly supplemented with technical innovations.
As a customer, you therefore benefit from a product that is highly mature and reliable at a solid price.
Components of the Offgridtec 150W Premium L 12V
1x Offgridtec PWM-Pro12/24-30 PWM Solar Charge Controller - 12V 30A PWM controller with display, load output, USB and more
1x Offgridtec 150W MONO V2 - monocrystalline solar module 018395
1x Offgridtec ABS cable entry 1-fold - black with waterproof PEG gland
1x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec Connection cable solar module to solar charge controller in motorhome design
1x Offgridtec 1,5m 10mm² Battery connection cable with MIDI fuse holder - Solar charge controller to battery connection cable
1x Offgridtec Battery poles clamps (1 pair)
1x Assembly adhesive set with instructions and necessary accessories for pre-treatment
1x MIDI fuse 40A 58V
The Offgridtec PWM-PRO 12/24-30 Solar Charge Controller
The Offgridtec PWM-Pro 12/24 charge controller series offers a large, convenient LCD display and works with the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. A controllable load output and 2 USB 5V outputs are also integrated into the controller and supply your 12V and 5V DC consumers with power. Please refer to the documentation of the charge controller for the complete range of functions.
The Offgridtec 150W MONO V2 solar panel
Only monocrystalline solar cells of the highest quality are used in the production of our modules. The module has a frame made of anodised aluminium and has specially hardened ESG solar glass, which makes it particularly resistant to external influences (weathering, etc.).
The expected daily output (April to October): 600Wh/day on average (max. 1200 Wh on sunny days in Germany).
Solar module dimensions: 1350 x 590 x 35 mm
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are supplied plug & play and are already pre-crimped with specialist tools. So you do not need to buy special pliers for the MC-4 connectors.
Components of the wiring set
1x Offgridtec 8m 2x6mm H07RN-F connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of pole terminals. The cable fits M8 screw terminals or batteries with round terminals.
Individual system adaptation possible on request
If you would like a different charge controller from our range, for example to charge board and service batteries together via solar, or if you would like the cables to have a different length, you are welcome to contact us at any time. The colour of the spoilers can also be changed from white to black. A short request for quotation with article number and change request to our customer service is sufficient. Any costs that may be incurred should be enquired about with our customer service.
Scope of delivery:
1x Offgridtec 4-01-007500 Premium-L 150W 12V motorhome solar system with all the above components
1x instruction manual
Product is expected to be back in stock on 29 March 2024
The Offgridtec mPremium+ xl-300w 12v (mpn 4-01-012410) is a premium solar kit for caravans and motor homes. The expected daily output (April to October) is 1200Wh/day on average (max. 2400 Wh on sunny days in Germany). Thanks to the included mppt solar charge controller, almost all common battery types such as 12v agm, gel or modern lithium can be mobile charged without any problems and according to their type. The system can be conveniently analyzed and even configured from a smartphone or tablet using a free app. Since the mPremium+ series is a further development of the popular mPremium series and differs only in the charge controller used, you can look forward to system components that have been tried and tested thousands of times and will ensure a long and reliable power supply for your mobile.
300W caravan complete set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our Solarasystems for caravans: We use an extra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class
We have also paid special attention to quality at the critical point, the cable feed-through into the interior of the motorhome. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
scope of delivery of the mPremium+ xl-300w caravan Solaranlage
2x Offgridtec 150w V2 - monocrystalline solar module 018395
1x Offgridtec abs cable gland 1-way - black with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 2x4mm² 20a battery connection cable - connection cable solar charge controller to battery
1x Offgridtec battery terminals (1 pair)
1x Y-connector
1x Victron Energy Smart mppt 100/20 solar charge controller with bluetooth module, load output and extensive configuration options.
1x mounting adhesive set with instructions and necessary accessories for pre-treatment
competent help if needed included!
All integrated system components at a glance
The Victron SmartSolar mppt 100/20
The Smartsolar 100/20 from Victron Energy (mpn scc110020060r) is a mppt solar charge controller with 20a max. charge current for charging 12v and 24v batteries of various types. Equipped with powerful charging algorithms and a bluetooth-based communication interface, the 100/20 offers all the features expected from a modern high-end charge controller:
bluetooth Smart integrated: allows setup and monitoring with a smartphone or other bluetooth enabled device.
Ultra fast maximum power point tracking (mppt).
Advanced maximum power point detection in case of partial shading.
20a load output
batterylife: intelligent battery management through load shedding.
Automatic battery voltage detection.
Flexible charging algorithms and much more.
overheating protection and load reduction at high temperatures.
The Offgridtec 150w V2 solar panel
monocrystalline solar cells of the highest quality are used exclusively in the production of our modules. The module has a frame made of anodized aluminum and has a specially hardened ESG solar glass, which makes it particularly resistant to external influences (weathering, etc.).
The expected daily output (April to October): average 120Wh/day (max. 2400 Wh on sunny days in Germany)
Solar module dimensions: 1350 x 590 x 35 mm
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the solar connectors.
1x Offgridtec 8m 2x6mm² h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x4mm² battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round poles.
1x Y-branch socket set
Individual system adaptation possible on request
If you would like to have a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. A short quote request with part number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
€523.42*
€439.85**
The Offgridtec mPremium+ xl-300w 12v (mpn 4-01-012410) is a premium solar kit for caravans and motor homes. The expected daily output (April to Octobe...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec mPremium+ xl-300w 12v (mpn 4-01-012410) is a premium solar kit for caravans and motor homes. The expected daily output (April to October) is 1200Wh/day on average (max. 2400 Wh on sunny days in Germany). Thanks to the included mppt solar charge controller, almost all common battery types such as 12v agm, gel or modern lithium can be mobile charged without any problems and according to their type. The system can be conveniently analyzed and even configured from a smartphone or tablet using a free app. Since the mPremium+ series is a further development of the popular mPremium series and differs only in the charge controller used, you can look forward to system components that have been tried and tested thousands of times and will ensure a long and reliable power supply for your mobile.
300W caravan complete set: simple, proven, high quality
The set contains all the components you need to charge your mobile batteries. The special thing about our Solarasystems for caravans: We use an extra solid mounting system that can be simply glued on. The module can be unscrewed from the spoiler at any time, should you need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class
We have also paid special attention to quality at the critical point, the cable feed-through into the interior of the motorhome. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
scope of delivery of the mPremium+ xl-300w caravan Solaranlage
2x Offgridtec 150w V2 - monocrystalline solar module 018395
1x Offgridtec abs cable gland 1-way - black with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in caravan design
1x Offgridtec 1,5m 2x4mm² 20a battery connection cable - connection cable solar charge controller to battery
1x Offgridtec battery terminals (1 pair)
1x Y-connector
1x Victron Energy Smart mppt 100/20 solar charge controller with bluetooth module, load output and extensive configuration options.
1x mounting adhesive set with instructions and necessary accessories for pre-treatment
competent help if needed included!
All integrated system components at a glance
The Victron SmartSolar mppt 100/20
The Smartsolar 100/20 from Victron Energy (mpn scc110020060r) is a mppt solar charge controller with 20a max. charge current for charging 12v and 24v batteries of various types. Equipped with powerful charging algorithms and a bluetooth-based communication interface, the 100/20 offers all the features expected from a modern high-end charge controller:
bluetooth Smart integrated: allows setup and monitoring with a smartphone or other bluetooth enabled device.
Ultra fast maximum power point tracking (mppt).
Advanced maximum power point detection in case of partial shading.
20a load output
batterylife: intelligent battery management through load shedding.
Automatic battery voltage detection.
Flexible charging algorithms and much more.
overheating protection and load reduction at high temperatures.
The Offgridtec 150w V2 solar panel
monocrystalline solar cells of the highest quality are used exclusively in the production of our modules. The module has a frame made of anodized aluminum and has a specially hardened ESG solar glass, which makes it particularly resistant to external influences (weathering, etc.).
The expected daily output (April to October): average 120Wh/day (max. 2400 Wh on sunny days in Germany)
Solar module dimensions: 1350 x 590 x 35 mm
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are delivered plug & play and are already pre-crimped with professional tools. So you don't need to buy special pliers for the solar connectors.
1x Offgridtec 8m 2x6mm² h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends.
1x Offgridtec 1.5m 2x4mm² battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round poles.
1x Y-branch socket set
Individual system adaptation possible on request
If you would like to have a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. A short quote request with part number and change request to our customer service is sufficient. Possible costs are to be inquired at the customer service.
Product is expected to be back in stock on 29 March 2024
The Offgridtec 300W Premium-L 12V (MPN 4-01-010960) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really leaves nothing to be desired. Installation takes less than two hours - practised hands are much quicker still. The expected daily output (April to October) is an average of 1200Wh/day (max. 2400 Wh on sunny days in Germany). The system is ideally suited for charging 12V AGM, GEL or lead-acid batteries.
300W complete motorhome set: simple, proven, high quality
The set contains all the components you need to charge your batteries on the move. The special thing about our solar systems for motorhomes: we use an extra-solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time should you ever need to access the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
We have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable grommet supplied is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely watertight and will last for many, many years.
Important performance features
We are the only manufacturer to offer you a complete mobile home solar system in which all components are supplied from our own production - of course, as usual, in the highest Offgridtec quality.
The Premium-Mobile system class is probably the best-selling motorhome solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again on the basis of customer experience and constantly supplemented with technical innovations.
As a customer, you therefore benefit from a product that is highly mature and reliable.
Components of the Offgridtec 300W Premium L 12V
1x Offgridtec PWM-Pro12/24-30 PWM solar charge controller - 12V 30A PWM controller with display, load output, USB and much more
2x Offgridtec 150W V2 - monocrystalline solar module 018395
1x Offgridtec ABS cable gland 1-fold - black; with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm H07RN-F - Connection cable solar module to solar charge controller in motorhome version
1x Offgridtec Solar Plug Junction Sockets
1x Offgridtec 1.5m 10mm Battery Connection Cable with MIDI Fuse Holder Connection Cable Solar Charge Controller to Battery
1x Offgridtec Battery Clamps (1 Pair)
1 x Mounting adhesive set with instructions and necessary accessories for pre-treatment
1x Dekalin 6252212 DEKAsyl MS-5 290 ml black; single cartridge power adhesive
1x MIDI fuse 40A 58V
The Offgridtec PWM-PRO solar charge controller
The Offgridtec PWM-Pro 12V 30A charge controller series offers a large, convenient LCD display and works with the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. A controllable load output and 2 USB 5V outputs are also integrated into the controller and supply your 12V and 5V DC consumers with power. Please refer to the documentation of the charge controller for the complete range of functions.
The Offgridtec 300W V2 Solar Panel
Only monocrystalline solar cells of the highest quality are used in the production of our modules. The module has a frame made of anodised aluminium and has specially hardened ESG solar glass, which makes it particularly resistant to external influences (weathering, etc.).
The expected daily output (April to October): on average 1200Wh/day (max. 2400 Wh on sunny days in Germany).
Solar module dimensions: 1350 x 590 x 35 mm
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All cables required for commissioning the solar system are included. In addition, all cables are supplied Plug & Play, i.e. they are fully equipped and processed with professional tools, which you therefore do not have to purchase separately.
Components of the cabling set
1x Offgridtec 8m 2x6mm H07RN-F connection cable solar module to solar charge controller complete with appropriately equipped cable ends
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of pole terminals. The cable fits M8 screw terminals or batteries with round terminals.
1x Offgridtec solar connector junction set - for parallel connection of the two solar modules.
Individual system adaptation possible on request
If you would like a different charge controller from our range, for example to charge board and service batteries together via solar, or if the cables should have a different length, you are welcome to contact us at any time. The colour of the spoilers can also be changed from white to black. A short request for quotation with article number and change request to our customer service is sufficient. Any costs that may be incurred should be enquired about with customer service.
Scope of delivery:
1x Offgridtec 4-01-010960 Premium-L 300W 12V motorhome solar system with all the above-mentioned components.
1x instruction manual
€498.61*
€419.00**
The Offgridtec 300W Premium-L 12V (MPN 4-01-010960) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really ...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec 300W Premium-L 12V (MPN 4-01-010960) is the perfect solar set for self-sufficient power supply in your motorhome or caravan and really leaves nothing to be desired. Installation takes less than two hours - practised hands are much quicker still. The expected daily output (April to October) is an average of 1200Wh/day (max. 2400 Wh on sunny days in Germany). The system is ideally suited for charging 12V AGM, GEL or lead-acid batteries.
300W complete motorhome set: simple, proven, high quality
The set contains all the components you need to charge your batteries on the move. The special thing about our solar systems for motorhomes: we use an extra-solid mounting system that can simply be glued on. The module can be unscrewed from the spoiler at any time should you ever need to access the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
We have also paid special attention to the critical point, the cable feed-through into the interior of the motorhome. The cable grommet supplied is made of the same sturdy material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely watertight and will last for many, many years.
Important performance features
We are the only manufacturer to offer you a complete mobile home solar system in which all components are supplied from our own production - of course, as usual, in the highest Offgridtec quality.
The Premium-Mobile system class is probably the best-selling motorhome solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again on the basis of customer experience and constantly supplemented with technical innovations.
As a customer, you therefore benefit from a product that is highly mature and reliable.
Components of the Offgridtec 300W Premium L 12V
1x Offgridtec PWM-Pro12/24-30 PWM solar charge controller - 12V 30A PWM controller with display, load output, USB and much more
2x Offgridtec 150W V2 - monocrystalline solar module 018395
1x Offgridtec ABS cable gland 1-fold - black; with waterproof PEG gland
2x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1x Offgridtec 8m 2x6mm H07RN-F - Connection cable solar module to solar charge controller in motorhome version
1x Offgridtec Solar Plug Junction Sockets
1x Offgridtec 1.5m 10mm Battery Connection Cable with MIDI Fuse Holder Connection Cable Solar Charge Controller to Battery
1x Offgridtec Battery Clamps (1 Pair)
1 x Mounting adhesive set with instructions and necessary accessories for pre-treatment
1x Dekalin 6252212 DEKAsyl MS-5 290 ml black; single cartridge power adhesive
1x MIDI fuse 40A 58V
The Offgridtec PWM-PRO solar charge controller
The Offgridtec PWM-Pro 12V 30A charge controller series offers a large, convenient LCD display and works with the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. A controllable load output and 2 USB 5V outputs are also integrated into the controller and supply your 12V and 5V DC consumers with power. Please refer to the documentation of the charge controller for the complete range of functions.
The Offgridtec 300W V2 Solar Panel
Only monocrystalline solar cells of the highest quality are used in the production of our modules. The module has a frame made of anodised aluminium and has specially hardened ESG solar glass, which makes it particularly resistant to external influences (weathering, etc.).
The expected daily output (April to October): on average 1200Wh/day (max. 2400 Wh on sunny days in Germany).
Solar module dimensions: 1350 x 590 x 35 mm
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All cables required for commissioning the solar system are included. In addition, all cables are supplied Plug & Play, i.e. they are fully equipped and processed with professional tools, which you therefore do not have to purchase separately.
Components of the cabling set
1x Offgridtec 8m 2x6mm H07RN-F connection cable solar module to solar charge controller complete with appropriately equipped cable ends
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of pole terminals. The cable fits M8 screw terminals or batteries with round terminals.
1x Offgridtec solar connector junction set - for parallel connection of the two solar modules.
Individual system adaptation possible on request
If you would like a different charge controller from our range, for example to charge board and service batteries together via solar, or if the cables should have a different length, you are welcome to contact us at any time. The colour of the spoilers can also be changed from white to black. A short request for quotation with article number and change request to our customer service is sufficient. Any costs that may be incurred should be enquired about with customer service.
Scope of delivery:
1x Offgridtec 4-01-010960 Premium-L 300W 12V motorhome solar system with all the above-mentioned components.
1x instruction manual
Product is expected to be back in stock on 29 March 2024
The Offgridtec 100w Premium-l 12v (mpn 4-01-002710) is the perfect solar set for self-sufficient power supply in your camper or caravan and really leaves nothing to be desired. The installation takes less than two hours - trained hands are even much faster. The expected daily output (April to October) is on average 400Wh/day (max. 850 Wh on sunny days in Germany) The system is suitable to charge batteries of type agm, gel or lead acid.
100w camper complete set: simple, proven, high quality
The set contains all components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an extra solid mounting system that can be easily glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
Important performance features
As the only manufacturer, we offer you a complete motorhome solar system, where all components are supplied from our own production - of course, as usual in the highest Offgridtec quality
The Premium-Mobile system class is probably the best-selling mobile home solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again based on customer experience and constantly supplemented with technical innovations.
As a customer, you thus benefit from a product that is highly mature and reliable and that is at
Components of the Offgridtec 100w Premium l 12v
1x Offgridtec 100w V2 Solarpanel 23V black frame
1xOffgridtecpWM-Pro 12/24-20 - 12v PWM solar charge controller with lCD display, load output, usb u.v.m.
1x Offgridtec Cable gland 1-way - black with waterproof PEG gland
1x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1xOffgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in motorhome design
1x Offgridtec 1,5m 2x6mm 30a battery connection cable and terminals - connection cable solar charge controller to battery
1x Mounting glue set with instructions and need accessories for pre-treatment
The Offgridtec pwm-pro solar charge controller
The Offgridtec PWM-Pro charge controller series offers a large, convenient lCD display and uses the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. Also a controllable load output as well as 2 usb 5v outputs are integrated in the controller and supply your 12v and 5v dc consumers with power. For the complete range of functions, please refer to the documentation of the charge controller
The Offgridtec MONO 100W V2 Solar Panel
The MONO 100W 23V is one of over 40 proven solar panels in the Offgridtec portfolio, benefiting from Offgridtec's expertise in manufacturing high-quality 12V and 24V solar cells. Thanks to its extremely durable solar glass, the module can be used even in very adverse operating conditions. It easily withstands storms or extreme cold and heat, and with the monocrystalline PERC cells, you can expect significant yields even on cloudy days.
Technical Specifications
• Power (Pmax): 100W
• Operating Voltage (Vmp): 23.9V
• Open-Circuit Voltage (Voc): 28V
• Maximum Current (Imp): 4.2A
• Efficiency: 22.3%
• NOCT: 45+/-2°C
• Short-Circuit Current (Isc): 4.4A
• Maximum System Voltage: 1000V
• Permissible Ambient Temperature: -40°C to +85°C
• Dimensions: 925 x 560 x 35mm
• Part Number: 3-01-018385
• Weight: 6.22kg
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are already pre-crimped with professional tools. So you don't need to buy special pliers for the mc-4 connectors. The cable has a length of 8m and accommodates 2 cores 6mm²
components of the cabling set
1x Offgridtec 8m 2x6mm h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round terminals.
Individual system customization possible on request
If you want a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. To do this, simply send a quote request with the item number and change request to our customer service. Possible costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-002710 Premium-l 100w 12v motorhome Solaranlage with all the above-mentioned components
1x instruction manual
€261.68*
€219.90**
The Offgridtec 100w Premium-l 12v (mpn 4-01-002710) is the perfect solar set for self-sufficient power supply in your camper or caravan and really lea...
Product is expected to be back in stock on 29 March 2024
Product is expected to be back in stock on 29 March 2024
The Offgridtec 100w Premium-l 12v (mpn 4-01-002710) is the perfect solar set for self-sufficient power supply in your camper or caravan and really leaves nothing to be desired. The installation takes less than two hours - trained hands are even much faster. The expected daily output (April to October) is on average 400Wh/day (max. 850 Wh on sunny days in Germany) The system is suitable to charge batteries of type agm, gel or lead acid.
100w camper complete set: simple, proven, high quality
The set contains all components you need to charge your batteries mobile. The special thing about our Solarasystems for motorhomes: We use an extra solid mounting system that can be easily glued on. The module can be unscrewed from the spoiler at any time, should you ever need to get to the area under the solar module. This set is designed so that it can be extended by another module in the same power class.
Also at the critical point, the cable grommet into the interior of the motorhome, we have paid attention to special quality. The supplied cable grommet is made of the same stable material as the roof spoiler for the solar modules and is simply glued on. The connection is absolutely waterproof and lasts for many, many years.
Important performance features
As the only manufacturer, we offer you a complete motorhome solar system, where all components are supplied from our own production - of course, as usual in the highest Offgridtec quality
The Premium-Mobile system class is probably the best-selling mobile home solar system on the market and has already been successfully installed thousands of times. In addition, the Premium-Mobile series established itself on the market more than 5 years ago and has been improved again and again based on customer experience and constantly supplemented with technical innovations.
As a customer, you thus benefit from a product that is highly mature and reliable and that is at
Components of the Offgridtec 100w Premium l 12v
1x Offgridtec 100w V2 Solarpanel 23V black frame
1xOffgridtecpWM-Pro 12/24-20 - 12v PWM solar charge controller with lCD display, load output, usb u.v.m.
1x Offgridtec Cable gland 1-way - black with waterproof PEG gland
1x Offgridtec ABS Mounting Spoiler 590mm black Pre-drilled incl. Stainless Steel Screws
1xOffgridtec 8m 2x6mm h07rnf - connecting cable solar module to solar charge controller in motorhome design
1x Offgridtec 1,5m 2x6mm 30a battery connection cable and terminals - connection cable solar charge controller to battery
1x Mounting glue set with instructions and need accessories for pre-treatment
The Offgridtec pwm-pro solar charge controller
The Offgridtec PWM-Pro charge controller series offers a large, convenient lCD display and uses the latest charging technologies. A large display informs the user about all operating states with the help of symbols. The state of charge is visually displayed in the manner of a fuel gauge. Data such as voltage, current and state of charge can also be shown digitally as a number on the display. In addition, the controller has a KWh counter that the user can reset himself. Also a controllable load output as well as 2 usb 5v outputs are integrated in the controller and supply your 12v and 5v dc consumers with power. For the complete range of functions, please refer to the documentation of the charge controller
The Offgridtec MONO 100W V2 Solar Panel
The MONO 100W 23V is one of over 40 proven solar panels in the Offgridtec portfolio, benefiting from Offgridtec's expertise in manufacturing high-quality 12V and 24V solar cells. Thanks to its extremely durable solar glass, the module can be used even in very adverse operating conditions. It easily withstands storms or extreme cold and heat, and with the monocrystalline PERC cells, you can expect significant yields even on cloudy days.
Technical Specifications
• Power (Pmax): 100W
• Operating Voltage (Vmp): 23.9V
• Open-Circuit Voltage (Voc): 28V
• Maximum Current (Imp): 4.2A
• Efficiency: 22.3%
• NOCT: 45+/-2°C
• Short-Circuit Current (Isc): 4.4A
• Maximum System Voltage: 1000V
• Permissible Ambient Temperature: -40°C to +85°C
• Dimensions: 925 x 560 x 35mm
• Part Number: 3-01-018385
• Weight: 6.22kg
Professional Solar Mounting System
Our ABS spoilers from Offgridtec are the ideal brackets for your solar module when it comes to achieving minimal weight with solid stability. The ABS plastic spoilers, available in black and white, provide an excellent solution for attaching solar panels to the roofs of motorhomes, campers, or caravans. Due to their elegant appearance, the spoilers, when paired with a solar module, not only offer functionality but also contribute to a well-rounded look for your motorhome. To minimize noise level and wind resistance, they have been aerodynamically shaped. The spoiler holes come pre-drilled from the factory and include matching stainless steel screws. Additionally, the product includes an installation manual for proper setup.
About the Holding Spoilers:
ABS plastic
Secure grip
Aerodynamic shape
Pre-drilled holes for easy and secure installation
Mounting materials included
Product Features:
Dimensions: L x W x H: 59cm x 8.9cm (of which approximately 3cm is the module contact area per spoiler) x 6.5cm
Manufacturer: Offgridtec
Material: ABS
Finish: polished
Color: black
Weight: 0.640 kilograms
The professional cabling set
All necessary cables are already pre-crimped with professional tools. So you don't need to buy special pliers for the mc-4 connectors. The cable has a length of 8m and accommodates 2 cores 6mm²
components of the cabling set
1x Offgridtec 8m 2x6mm h07rn-f connection cable solar module to solar charge controller complete with appropriately equipped cable ends
1x Offgridtec 1.5m 2x6mm battery connection cable with flat fuse holder, matching ATO fuse and a pair of binding posts. The cable fits m8 screw terminals or batteries with round terminals.
Individual system customization possible on request
If you want a different charge controller from our range, for example to charge board and service batteries together via solar, or the cables should have a different length, you can always contact us. Also the color of the spoilers can be changed from white to black. To do this, simply send a quote request with the item number and change request to our customer service. Possible costs are to be inquired at the customer service.
scope of delivery:
1x Offgridtec 4-01-002710 Premium-l 100w 12v motorhome Solaranlage with all the above-mentioned components
1x instruction manual
Product is expected to be back in stock on 29 March 2024
This solar set for autarkic power supply in caravans leaves nothing to be desired. Innovative Mpp-Dual charge controller technology combined with a high-efficient Offgridtec 150W SP-Ultra 24 High-End Solar Module
guarantees a very high energy output. This system is especially designed for caravans and includes everything - except batteries - for installation and operation. The charge controller also allows the
connection to the caravan's Schaudt-EBL (EBL-connection-cable needed). All components in this set meet highest demands.
Special features:
The solar-generator is a high-end solar module with American Sunpower back-contact cells. The degree of effectiveness (>20%) is much above average.
The included modules out of the SPR-series are much smaller than common modules with the same performance.
Dual-Charging-Technology made in Germany allows the the charging of on-board and starter battery at the same time.
MPP-Tracker: Maximum Power Point Tracking ensures the highest possible output
EBL-option: can be operated on a Schaudt-EBL or directly on up to 2 different battery cycles
Daily output:
Average output during summer (May - October): 520Wh daily (measured in the north of Germany - more output can be expected in the south)
Our Solar-Mobil-line provides high-quality components at a fair price. Simply compare the item prices of the included products.
Components:
1 x Offgridtec 150W SP-ULtra 24V High-End Solar Panel
1 x Votronic MPP 165 Duo Digital Solar Charge Controller
1 x Votronic LCD Solar Computer S
1 x cable entry black
1 x roof-spoiler set black
1 x 8m solar cable (2x6mm²) - plug & play
1 x 1,5m battery cable with fuse and EBL-connection-cable
1 x Mounting-Glue Set with needed accessories to prepare your roof
1 x MC4-Y connector pair
With this set you have everything to charge your batteries. Our special mounting system is and can easily be glued on your caravan's roof. If you have to reach the surface beneath the module it can be screwed off the mounting-spoilers at any time. All our sets can be expanded by modules of the same performance class.
The critical spot of the mounting system is the cableentry through your roof. We use the same high-quality material as we do for the mounting-spoilers and is also attached with Mounting-glue. The cable entry is absolutly waterproof and lasts for many years.
Our Solar-Mobil-line provides high-quality components at a fair price. Simply compare the item prices of the included products.
Offgridtec 150W SP-Ultra 12V Solar Module
Monocrystalline 150W / 12V high-end solar panel with back-contacted high-power solar cells produced by Sunpower - a high-quality product with an efficiency of 21%.
The world's best solar cells meet with the new Back-Contact process. The outcome is a high-end product at an adequate price.
We made sure that the other components match the these special solar cells. This panel is lighter and has a smaller surface than common panels with the same performance.
Additionally the SP-line's light conversion rate is much higher compared to the mono-line - even during shady periods.
Technical data:
Performance (Pmax): 150W
Voltage (Vmpp): 23.2V
Max. current (Impp): 6.47A
No-load voltage (Voc): 27.38V
Short-circuit current (Isc): 6.98A
Ambient temperature: -40...+85°C
Max. system voltage: 1000V DC
Dimensions: 1440 x 540 x 35mm
Weight: 9,37 kg
Votronic MPP 165 Duo Digital Solar Charge Controller
Controllers according to the MPP technology are continuously and automatically calculating the maximum power yield (MPP) of the solar modules several times per minute.
The voltage surplus of the solar module will be transformed to a higher charging current for the battery (realised by high-frequency switching controller technology with high efficiency).
This surplus of charging current ensures short charging times and the best possible power yield of the solar system.
Main Charging Port I: Automatic charging and conservation of charge of the (main) board supply battery
Auxiliary Charging Port II: Current and voltage reduced for recharging as well as trickle charge of the vehicle’s starter battery, thus ensuring continuous starting capacity
Continuous control, full batteries by immediate recharging in case of current consumption
Automatic charging programs adjustable for gel, acid/lead-acid and AGM/fleece batteries for optimum charging results
Indicators for operating state "Full", "Charging", "MPP" and "Low Voltage"
Very low own electricity consumption, high efficiency
LCD Solar Computer S
This computer measures and displays all values to improve the control and surveillance of your solar system. The currently produced solar energy is displayed as bar chart for a quick check up.
The display has background lighting so all data can also be read from greater distance and bad illumination.
Roof-spoiler Mounting Kit
Spoiler profiles are the first choice when it comes to proper attachment of solar modules on caravans. Aligned in driving direction wind noises are no problem, even on
caravans with an alcove. Thanks to the spoiler's closed design branches can not get under the module.
The Bonding
A proper adhesion is superior to every screw connection. On a lacquered surface or on fiberglass a tractive power of more than 4 N/mm2 can be reached, a value that could not be reached with screws in a very thin aluminum or fiberglass sheet. Even for amateurs it is possible to make a perfectly firm connection between spoilers and surface.
Cable Set
You don't have to buy extra tools for the MC4-plugs in this set as all necessary cables are already crimped. The comes with a length of 8m and consists of 2x4mm²-wires.
Double Cable Entry
Cable entries that lead cables into the your caravan are always a most critical spot as they have to be absolutely waterproof for years. Even the smallest water inlet can cause
irreparable damage especially where humidity is not easily noticed. To avoid such problems cable entries were developed:
The cable entries are made of the same UV- and corrosion resistant material as the mounting profiles you find in our shop. They are very robust and absolutely treadable. The broad adhesive edge keeps it waterproof. They are also attached with Sikaflex-glue and can be painted in a color fitting the vehicle.
€578.40*
€486.05**
This solar set for autarkic power supply in caravans leaves nothing to be desired. Innovative Mpp-Dual charge controller technology combined with a h...
Product is expected to be back in stock on 10 April 2024
Product is expected to be back in stock on 10 April 2024
This solar set for autarkic power supply in caravans leaves nothing to be desired. Innovative Mpp-Dual charge controller technology combined with a high-efficient Offgridtec 150W SP-Ultra 24 High-End Solar Module
guarantees a very high energy output. This system is especially designed for caravans and includes everything - except batteries - for installation and operation. The charge controller also allows the
connection to the caravan's Schaudt-EBL (EBL-connection-cable needed). All components in this set meet highest demands.
Special features:
The solar-generator is a high-end solar module with American Sunpower back-contact cells. The degree of effectiveness (>20%) is much above average.
The included modules out of the SPR-series are much smaller than common modules with the same performance.
Dual-Charging-Technology made in Germany allows the the charging of on-board and starter battery at the same time.
MPP-Tracker: Maximum Power Point Tracking ensures the highest possible output
EBL-option: can be operated on a Schaudt-EBL or directly on up to 2 different battery cycles
Daily output:
Average output during summer (May - October): 520Wh daily (measured in the north of Germany - more output can be expected in the south)
Our Solar-Mobil-line provides high-quality components at a fair price. Simply compare the item prices of the included products.
Components:
1 x Offgridtec 150W SP-ULtra 24V High-End Solar Panel
1 x Votronic MPP 165 Duo Digital Solar Charge Controller
1 x Votronic LCD Solar Computer S
1 x cable entry black
1 x roof-spoiler set black
1 x 8m solar cable (2x6mm²) - plug & play
1 x 1,5m battery cable with fuse and EBL-connection-cable
1 x Mounting-Glue Set with needed accessories to prepare your roof
1 x MC4-Y connector pair
With this set you have everything to charge your batteries. Our special mounting system is and can easily be glued on your caravan's roof. If you have to reach the surface beneath the module it can be screwed off the mounting-spoilers at any time. All our sets can be expanded by modules of the same performance class.
The critical spot of the mounting system is the cableentry through your roof. We use the same high-quality material as we do for the mounting-spoilers and is also attached with Mounting-glue. The cable entry is absolutly waterproof and lasts for many years.
Our Solar-Mobil-line provides high-quality components at a fair price. Simply compare the item prices of the included products.
Offgridtec 150W SP-Ultra 12V Solar Module
Monocrystalline 150W / 12V high-end solar panel with back-contacted high-power solar cells produced by Sunpower - a high-quality product with an efficiency of 21%.
The world's best solar cells meet with the new Back-Contact process. The outcome is a high-end product at an adequate price.
We made sure that the other components match the these special solar cells. This panel is lighter and has a smaller surface than common panels with the same performance.
Additionally the SP-line's light conversion rate is much higher compared to the mono-line - even during shady periods.
Technical data:
Performance (Pmax): 150W
Voltage (Vmpp): 23.2V
Max. current (Impp): 6.47A
No-load voltage (Voc): 27.38V
Short-circuit current (Isc): 6.98A
Ambient temperature: -40...+85°C
Max. system voltage: 1000V DC
Dimensions: 1440 x 540 x 35mm
Weight: 9,37 kg
Votronic MPP 165 Duo Digital Solar Charge Controller
Controllers according to the MPP technology are continuously and automatically calculating the maximum power yield (MPP) of the solar modules several times per minute.
The voltage surplus of the solar module will be transformed to a higher charging current for the battery (realised by high-frequency switching controller technology with high efficiency).
This surplus of charging current ensures short charging times and the best possible power yield of the solar system.
Main Charging Port I: Automatic charging and conservation of charge of the (main) board supply battery
Auxiliary Charging Port II: Current and voltage reduced for recharging as well as trickle charge of the vehicle’s starter battery, thus ensuring continuous starting capacity
Continuous control, full batteries by immediate recharging in case of current consumption
Automatic charging programs adjustable for gel, acid/lead-acid and AGM/fleece batteries for optimum charging results
Indicators for operating state "Full", "Charging", "MPP" and "Low Voltage"
Very low own electricity consumption, high efficiency
LCD Solar Computer S
This computer measures and displays all values to improve the control and surveillance of your solar system. The currently produced solar energy is displayed as bar chart for a quick check up.
The display has background lighting so all data can also be read from greater distance and bad illumination.
Roof-spoiler Mounting Kit
Spoiler profiles are the first choice when it comes to proper attachment of solar modules on caravans. Aligned in driving direction wind noises are no problem, even on
caravans with an alcove. Thanks to the spoiler's closed design branches can not get under the module.
The Bonding
A proper adhesion is superior to every screw connection. On a lacquered surface or on fiberglass a tractive power of more than 4 N/mm2 can be reached, a value that could not be reached with screws in a very thin aluminum or fiberglass sheet. Even for amateurs it is possible to make a perfectly firm connection between spoilers and surface.
Cable Set
You don't have to buy extra tools for the MC4-plugs in this set as all necessary cables are already crimped. The comes with a length of 8m and consists of 2x4mm²-wires.
Double Cable Entry
Cable entries that lead cables into the your caravan are always a most critical spot as they have to be absolutely waterproof for years. Even the smallest water inlet can cause
irreparable damage especially where humidity is not easily noticed. To avoid such problems cable entries were developed:
The cable entries are made of the same UV- and corrosion resistant material as the mounting profiles you find in our shop. They are very robust and absolutely treadable. The broad adhesive edge keeps it waterproof. They are also attached with Sikaflex-glue and can be painted in a color fitting the vehicle.
Product is expected to be back in stock on 10 April 2024