Centaur
- Batteries
- Electronics
- Generators
- Installation
- Complete Systems
-
Brands
- AEconversion
- Bluetti
- BYD
- Canadian Solar
- EcoFlow
- EFOY
- Fothermo
- Growatt
- Hoymiles
- Huawei
- JA Solar
- Jinko Solar
- Jokari
- Kemo
- Lapp
- Longi
- Luxen Solar
- Mastervolt
- myStrom
- Offgridtec
- Pylontech
- Pytes
- Risen
- Steca
- Trina Solar
- Victron Energy
- Votronic
- Wattstone
- Wieland Electric
- Yingli
- Zendure
Filter
–
Centaur
8 Results
Sorting
1-67-012040
Victron Centaur Charger 12/80 (3)12v 80a battery charger 3 outputs
The Centaur 12/80 (3) from victron Energy (mpn cch012080000) is a high quality battery charger for 12v batteries with 3 charging outputs and 80a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/80 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 12/80 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012080000 3 battery charging outputs, each can supply full 80a charging current (maximum total charging current = 80a) suitable for batteries with capacity from 320Ah - 800Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/80 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/80 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 12/80; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch012080000 Centaur 12/80 (3) 1x installation manual
The Centaur 12/80 (3) from victron Energy (mpn cch012080000) is a high quality battery charger for 12v batteries with 3 charging outputs and 80a maxim...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 12/80 (3) from victron Energy (mpn cch012080000) is a high quality battery charger for 12v batteries with 3 charging outputs and 80a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/80 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 12/80 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012080000 3 battery charging outputs, each can supply full 80a charging current (maximum total charging current = 80a) suitable for batteries with capacity from 320Ah - 800Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/80 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/80 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 12/80; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch012080000 Centaur 12/80 (3) 1x installation manual
Shipped in 10-14 Werktage
1-67-012015
Victron Centaur Charger 12/20 (3) 12v 20a battery charger 3 outputs
The Centaur 12/20 (3) from victron Energy (mpn cch012020000) is a high quality battery charger for 12v batteries with 3 charging outputs and 20a maximum charging current, which can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/20 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 12/20 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012020000 3 battery charging outputs, each can supply full 20a charging current (maximum total charging current = 20a) suitable for batteries with capacity from 80Ah - 200Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/20 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/20 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 12/20; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch012020000 Centaur 12/20 (3) 1x installation manual
The Centaur 12/20 (3) from victron Energy (mpn cch012020000) is a high quality battery charger for 12v batteries with 3 charging outputs and 20a maxim...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 12/20 (3) from victron Energy (mpn cch012020000) is a high quality battery charger for 12v batteries with 3 charging outputs and 20a maximum charging current, which can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/20 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 12/20 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012020000 3 battery charging outputs, each can supply full 20a charging current (maximum total charging current = 20a) suitable for batteries with capacity from 80Ah - 200Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/20 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/20 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 12/20; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch012020000 Centaur 12/20 (3) 1x installation manual
Shipped in 10-14 Werktage
1-67-012035
Victron Centaur Charger 12/60 (3) 12v 60a battery charger 3 outputs
The Centaur 12/60 (3) from victron Energy (mpn cch012060000) is a high-quality battery charger for 12v batteries with 3 charging outputs and a maximum charging current of 60a, which can be distributed to the 3 outputs as required. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/60 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead-acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high-frequency controlled. The power input is electronically regulated in the first power stage via the power factor. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high-performance batteries can be charged simultaneously with this charger. important features of the Centaur 12/60 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012060000 3 battery charging outputs, each can supply a full 60a charging current (maximum total charging current = 60a) suitable for batteries with a capacity of 240Ah - 600Ah three-stage IUoU charging characteristic universal 90 - 265v ac input for mains connection, which can operate at both 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/60 (3): Quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/60 to withstand the toughest conditions such as heat, moisture and salty atmospheres. The circuit boards are protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced under extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges with constant current (bulk) until the charging current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase at the end of which a trickle charge phase follows. The charging voltage is regulated via the internal temperature sensor (-2mv/°C per cell). The full charging current is distributed to three outputs, with each output delivering full power when only one battery is connected. Different battery types can be used on the Centaur 12/60; the default setting is for gel batteries. Other batteries (lead acid or agm) can be used after making the appropriate setting on the inching switch (bottom left behind the front panel). Scope of delivery: 1x victron Energy cch012060000 Centaur 12/60 (3) 1x installation instructions
The Centaur 12/60 (3) from victron Energy (mpn cch012060000) is a high-quality battery charger for 12v batteries with 3 charging outputs and a maximum...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 12/60 (3) from victron Energy (mpn cch012060000) is a high-quality battery charger for 12v batteries with 3 charging outputs and a maximum charging current of 60a, which can be distributed to the 3 outputs as required. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/60 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead-acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high-frequency controlled. The power input is electronically regulated in the first power stage via the power factor. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high-performance batteries can be charged simultaneously with this charger. important features of the Centaur 12/60 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012060000 3 battery charging outputs, each can supply a full 60a charging current (maximum total charging current = 60a) suitable for batteries with a capacity of 240Ah - 600Ah three-stage IUoU charging characteristic universal 90 - 265v ac input for mains connection, which can operate at both 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/60 (3): Quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/60 to withstand the toughest conditions such as heat, moisture and salty atmospheres. The circuit boards are protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced under extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges with constant current (bulk) until the charging current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase at the end of which a trickle charge phase follows. The charging voltage is regulated via the internal temperature sensor (-2mv/°C per cell). The full charging current is distributed to three outputs, with each output delivering full power when only one battery is connected. Different battery types can be used on the Centaur 12/60; the default setting is for gel batteries. Other batteries (lead acid or agm) can be used after making the appropriate setting on the inching switch (bottom left behind the front panel). Scope of delivery: 1x victron Energy cch012060000 Centaur 12/60 (3) 1x installation instructions
Shipped in 10-14 Werktage
1-67-012060
Victron Centaur Charger 24/40 (3) 24v 40a battery charger 3 outputs
The Centaur 24/40 (3) from victron Energy (mpn cch024040000) is a high quality battery charger for 24v batteries with 3 charging outputs and 40a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/40 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(s). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/40 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024040000 3 battery charging outputs, each can supply full 40a charging current (maximum total charging current = 40a) suitable for batteries with a capacity of 160Ah - 400Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/40 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/40 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/40; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024040000 Centaur 24/40 (3) 1x installation manual
The Centaur 24/40 (3) from victron Energy (mpn cch024040000) is a high quality battery charger for 24v batteries with 3 charging outputs and 40a maxim...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 24/40 (3) from victron Energy (mpn cch024040000) is a high quality battery charger for 24v batteries with 3 charging outputs and 40a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/40 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(s). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/40 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024040000 3 battery charging outputs, each can supply full 40a charging current (maximum total charging current = 40a) suitable for batteries with a capacity of 160Ah - 400Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/40 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/40 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/40; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024040000 Centaur 24/40 (3) 1x installation manual
Shipped in 10-14 Werktage
1-67-012055
Victron Centaur Charger 24/30 (3) 24v 30a battery charger 3 outputs
The Centaur 24/30 (3) from victron Energy (mpn cch024030000) is a high quality battery charger for 24v batteries with 3 charging outputs and 30a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/30 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(s). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/30 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024030000 3 battery charging outputs, each can supply full 30a charging current (maximum total charging current = 30a) suitable for batteries with capacity from 120Ah - 300Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/30 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/30 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/30; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024030000 Centaur 24/30 (3) 1x installation manual
The Centaur 24/30 (3) from victron Energy (mpn cch024030000) is a high quality battery charger for 24v batteries with 3 charging outputs and 30a maxim...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 24/30 (3) from victron Energy (mpn cch024030000) is a high quality battery charger for 24v batteries with 3 charging outputs and 30a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/30 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(s). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/30 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024030000 3 battery charging outputs, each can supply full 30a charging current (maximum total charging current = 30a) suitable for batteries with capacity from 120Ah - 300Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/30 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/30 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/30; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024030000 Centaur 24/30 (3) 1x installation manual
Shipped in 10-14 Werktage
1-67-012045
Victron Centaur Charger 12/100 (3)12v 100a battery charger 3 outputs
The Centaur 12/100 (3) from victron Energy (mpn cch012100000) is a high quality battery charger for 12v batteries with 3 charging outputs and 100a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/100 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 12/100 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012100000 3 battery charging outputs, each can supply full 100a charging current (maximum total charging current = 100a) suitable for batteries with capacity from 400Ah - 1000Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/100 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/100 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 12/100; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch012100000 Centaur 12/100 (3) 1x installation manual
The Centaur 12/100 (3) from victron Energy (mpn cch012100000) is a high quality battery charger for 12v batteries with 3 charging outputs and 100a max...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 12/100 (3) from victron Energy (mpn cch012100000) is a high quality battery charger for 12v batteries with 3 charging outputs and 100a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 12/100 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 12/100 at a glance for 12v battery voltage, ip20 protection class victron Part number: cch012100000 3 battery charging outputs, each can supply full 100a charging current (maximum total charging current = 100a) suitable for batteries with capacity from 400Ah - 1000Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 12/100 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 12/100 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 12/100; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch012100000 Centaur 12/100 (3) 1x installation manual
Shipped in 10-14 Werktage
1-67-012065
Victron Centaur Charger 24/60 (3) 24v 60a battery charger 3 outputs
The Centaur 24/60 (3) from victron Energy (mpn cch024060000) is a high quality battery charger for 24v batteries with 3 charging outputs and 60a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/60 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/60 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024060000 3 battery charging outputs, each can supply full 60a charging current (maximum total charging current = 60a) suitable for batteries with capacity from 240Ah - 600Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/60 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/60 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/60; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024060000 Centaur 24/60 (3) 1x installation manual
The Centaur 24/60 (3) from victron Energy (mpn cch024060000) is a high quality battery charger for 24v batteries with 3 charging outputs and 60a maxim...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 24/60 (3) from victron Energy (mpn cch024060000) is a high quality battery charger for 24v batteries with 3 charging outputs and 60a maximum charging current that can be distributed as desired among the 3 outputs. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/60 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/60 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024060000 3 battery charging outputs, each can supply full 60a charging current (maximum total charging current = 60a) suitable for batteries with capacity from 240Ah - 600Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/60 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/60 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/60; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024060000 Centaur 24/60 (3) 1x installation manual
Shipped in 10-14 Werktage
1-67-012050
Victron Centaur Charger 24/16 (3) 24v 16a battery charger 3 outputs
The Centaur 24/16 (3) from victron Energy (mpn cch024016000) is a high quality battery charger for 24v batteries with 3 charging outputs and 16a maximum charging current, which can be distributed to the 3 outputs as desired. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/16 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/16 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024016000 3 battery charging outputs, each can supply full 16a charging current (maximum total charging current = 16a) suitable for batteries with a capacity of 45Ah - 150Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/16 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/16 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/16; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024016000 Centaur 24/16 (3) 1x installation manual
The Centaur 24/16 (3) from victron Energy (mpn cch024016000) is a high quality battery charger for 24v batteries with 3 charging outputs and 16a maxim...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
The Centaur 24/16 (3) from victron Energy (mpn cch024016000) is a high quality battery charger for 24v batteries with 3 charging outputs and 16a maximum charging current, which can be distributed to the 3 outputs as desired. Thanks to its wide input voltage range of 90-265 v ac, the Centaur 24/16 (3) can be used almost anywhere in the world without any special settings. The IUoU charging characteristic with three-stage characteristic ensures gentle charging of your battery(ies). The Centaur is suitable for charging gel, agm and lead acid batteries, where the battery type can be quickly selected via a DIP switch on the housing of the device. The Centaur battery charger is fully high frequency regulated. The power input is electronically controlled by the power factor in the first power stage. The next stage provides galvanic isolation and ensures perfect DC voltage at the outputs. The electronic components are protected against moisture and dirt by a special coating to ensure the longevity of the device. Three high power batteries can be charged simultaneously with this charger important features of the Centaur 24/16 at a glance for 24v battery voltage, ip20 protection class victron Part number: cch024016000 3 battery charging outputs, each can supply full 16a charging current (maximum total charging current = 16a) suitable for batteries with a capacity of 45Ah - 150Ah three-stage IUoU charging curve universal 90 - 265v ac input for mains connection, which can work with both at 50 Hz and 60 Hz suitable for charging gel, agm and lead-acid batteries Centaur 24/16 (3): quality without compromise An aluminum housing with epoxy powder coating, drip protection against condensation water and stainless steel mounting parts allow the Centaur 24/16 to withstand the toughest demands such as heat, humidity and salty atmospheres. The circuit boards are safely protected against corrosion by an acrylic coating. Temperature sensors ensure that all power components operate within specified limits and, if necessary, the output current is automatically reduced in extreme conditions. Three-stage charging characteristic with temperature compensation Centaur initially charges at constant current (bulk) until the charge current has dropped to 70% of the nominal value. This is followed by a fixed four-hour constant voltage phase, at the end of which a trickle charge phase follows. The charging voltage is controlled by the internal temperature sensor (-2mv/°C per cell). The full charge current is distributed over three outputs, each output delivering full power on its own when only one battery is connected Different battery types can be used on the Centaur 24/16; the default setting refers to gel batteries. Other batteries (lead acid or agm) can be used after appropriate setting on the jog switch (lower left behind the front front panel) Scope of delivery: 1x victron Energy cch024016000 Centaur 24/16 (3) 1x installation manual
Shipped in 10-14 Werktage