Argodiodes
- Batteries
- Electronics
- Generators
- Installation
- Complete Systems
-
Brands
- AEconversion
- Bluetti
- BYD
- Canadian Solar
- EcoFlow
- EFOY
- Fothermo
- Growatt
- Hoymiles
- Huawei
- JA Solar
- Jinko Solar
- Jokari
- Kemo
- Lapp
- Longi
- Luxen Solar
- Mastervolt
- myStrom
- Offgridtec
- Pylontech
- Pytes
- Risen
- Steca
- Trina Solar
- Victron Energy
- Votronic
- Wattstone
- Wieland Electric
- Yingli
- Zendure
Filter
–
Argodiodes
7 Results
Sorting
8-67-009245
Victron Argo-diode 100-3AC 100A Battery isolator
The Victron Argo 120-2AC battery isolator (MPN ARG120201020R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 120-2AC provides a max. charging current of 120A and supports 2 batteries or battery banks
alternator max. current 100A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG120201020R Argo 120-2AC Isolator 120A for 2 batteries1x Manual
The Victron Argo 120-2AC battery isolator (MPN ARG120201020R) allows the current distribution out of one energy source (e.g. alternator) to multiple b...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
8-67-009245
Victron Argo-diode 100-3AC 100A Battery isolator
The Victron Argo 120-2AC battery isolator (MPN ARG120201020R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 120-2AC provides a max. charging current of 120A and supports 2 batteries or battery banks
alternator max. current 100A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG120201020R Argo 120-2AC Isolator 120A for 2 batteries1x Manual
Shipped in 10-14 Werktage
8-67-009260
Victron Argo-diode 180-3AC 180A Battery isolator
The Victron Argo 180-3AC battery isolator (MPN ARG180301020) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 180-3AC provides a max. charging current of 180A and supports 3 batteries or battery banks
alternator max. current 180A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG180301020 Argo 180-3AC Isolator 180A for 3 batteries1x Manual
The Victron Argo 180-3AC battery isolator (MPN ARG180301020) allows the current distribution out of one energy source (e.g. alternator) to multiple ba...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
8-67-009260
Victron Argo-diode 180-3AC 180A Battery isolator
The Victron Argo 180-3AC battery isolator (MPN ARG180301020) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 180-3AC provides a max. charging current of 180A and supports 3 batteries or battery banks
alternator max. current 180A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG180301020 Argo 180-3AC Isolator 180A for 3 batteries1x Manual
Shipped in 10-14 Werktage
8-67-009255
Victron Argo-diode 160-2AC 160A Battery isolator
The Victron Argo 160-2AC battery isolator (MPN ARG160201020) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 160-2AC provides a max. charging current of 160A and supports 2 batteries or battery banks
alternator max. current 160A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG160201020 Argo 160-2AC Isolator 160A for 2 batteries1x Manual
The Victron Argo 160-2AC battery isolator (MPN ARG160201020) allows the current distribution out of one energy source (e.g. alternator) to multiple ba...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
8-67-009255
Victron Argo-diode 160-2AC 160A Battery isolator
The Victron Argo 160-2AC battery isolator (MPN ARG160201020) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 160-2AC provides a max. charging current of 160A and supports 2 batteries or battery banks
alternator max. current 160A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG160201020 Argo 160-2AC Isolator 160A for 2 batteries1x Manual
Shipped in 10-14 Werktage
8-67-009240
Victron Argodiode 100-3AC 100A Battery isolator
The Victron Argo 100-3AC battery isolator (MPN ARG100301000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 100-3AC provides a max. charging current of 100A and supports 3 batteries or battery banks
alternator max. current 100A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG100301000R Argo 100-3AC Isolator 100A for 3 batteries1x Manual
The Victron Argo 100-3AC battery isolator (MPN ARG100301000R) allows the current distribution out of one energy source (e.g. alternator) to multiple b...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
8-67-009240
Victron Argodiode 100-3AC 100A Battery isolator
The Victron Argo 100-3AC battery isolator (MPN ARG100301000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 100-3AC provides a max. charging current of 100A and supports 3 batteries or battery banks
alternator max. current 100A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG100301000R Argo 100-3AC Isolator 100A for 3 batteries1x Manual
Shipped in 10-14 Werktage
8-67-009230
Victron Argo Diode 80-2AC 80A Battery isolator
The Victron Argo 80-2AC battery isolator (MPN ARG080201000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 80-2AC provides a max. charging current of 80A and supports 2 batteries or battery banks
alternator max. current 80A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG080201000R Argo 80-2AC Isolator 80A for 2 batteries
The Victron Argo 80-2AC battery isolator (MPN ARG080201000R) allows the current distribution out of one energy source (e.g. alternator) to multiple ba...
Shipped in 10-14 Werktage
Shipped in 10-14 Werktage
8-67-009230
Victron Argo Diode 80-2AC 80A Battery isolator
The Victron Argo 80-2AC battery isolator (MPN ARG080201000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 80-2AC provides a max. charging current of 80A and supports 2 batteries or battery banks
alternator max. current 80A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG080201000R Argo 80-2AC Isolator 80A for 2 batteries
Shipped in 10-14 Werktage
8-67-009250
Victron Argo-diode 140-3AC 140A Battery isolator
The Victron Argo 140-3AC battery isolator (MPN ARG140301020R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 140-3AC provides a max. charging current of 140A and supports 3 batteries or battery banks
alternator max. current 140A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG140301020R Argo 140-3AC Isolator 140A for 3 batteries1x Manual
The Victron Argo 140-3AC battery isolator (MPN ARG140301020R) allows the current distribution out of one energy source (e.g. alternator) to multiple b...
Shipped in 1-3 days
Shipped in 1-3 days
8-67-009250
Victron Argo-diode 140-3AC 140A Battery isolator
The Victron Argo 140-3AC battery isolator (MPN ARG140301020R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
equipped with current-limiting connector for alternator energize input (generators, alternator,...)
Argo 140-3AC provides a max. charging current of 140A and supports 3 batteries or battery banks
alternator max. current 140A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG140301020R Argo 140-3AC Isolator 140A for 3 batteries1x Manual
Shipped in 1-3 days
8-67-009235
Victron Argodiode 80-2SC 80A Battery Isolator
The Victron Argo 80-2SC battery isolator (MPN ARG080202000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.Compared to the 80-2AC this model is not equipped with current-limiting generator connection.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
Argo 80-2SC provides a max. charging current of 80A and supports 2 batteries or battery banks
alternator max. current 80A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG080202000R Argo80-2SC Isolator 80A for 2 batteries1x Manual
The Victron Argo 80-2SC battery isolator (MPN ARG080202000R) allows the current distribution out of one energy source (e.g. alternator) to multiple ba...
Soon available again
Soon available again
8-67-009235
Victron Argodiode 80-2SC 80A Battery Isolator
The Victron Argo 80-2SC battery isolator (MPN ARG080202000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.Compared to the 80-2AC this model is not equipped with current-limiting generator connection.
With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs.
Features:
latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum.
Argo 80-2SC provides a max. charging current of 80A and supports 2 batteries or battery banks
alternator max. current 80A - supply battery can be used without discharging the starter battery
Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging.
Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery.
Delivery scope:1x Victron ARG080202000R Argo80-2SC Isolator 80A for 2 batteries1x Manual
Soon available again