The mk3 usb to VE.Bus interface from Victron Energy (mpn ass030140000) connects your computer or a notebook to a variety of Victron products via the VE.Bus port. The interface enables you to use a whole range of Victron programs to configure and analyze your Victron product. The easiest way to configure complex systems or single devices to your needs. following free programs can be used with the help of the interface: VEConfigure 3 (v9004193) VE.Bus Quick Configure (v9010137) - For installation of 3 phase system, for example with three Multiplus inverters. VE.Bus System Configurator (v9009132) - For complex systems VEFlash (v9005147) - for easy firmware updates of Victron products with VE.Bus the following device families are currently compatible with the VE.Bus to usb interface: Multi MultiGrid MultiPlus Quattro Phoenix Wechselrichter (Only models with a VE.Bus communication port) ECOmulti EasySolar EasyPlus Scope of delivery:1x Victron Energy ASS030140000 mk3-usb (VE.Bus to usb) Interface

The Multiplus-II 48/3000/35-32 is a high-end device combination from victron Energy (mpn pmp482305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and the potential range of use to ess applications. The inverter module delivers a whopping 3000 w at non-linear load, or 2400 w at linear continuous load. the 48 v battery charger is also very well proportioned with 35 a charging power and is complemented by a 32 a transfer switch that allows lightning-fast switching between the aC connections important features of the Multiplus-II 48/3000/35-32 PowerControl and Powerassist -increase of mains or generator power built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 3000w power at non-linear load 2400 w continuous load and 6000 w peak power for 48 v battery voltage, 32 a transfer switch and 35 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/3000/35-32. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482305010 Multiplus-II 48/3000/35-32a 1x user manual

The Multiplus-II 48/5000/70-50 is a high-end device combination by Victron Energy (mpn: pmp482505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and expands the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 70 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections important features of the Multiplus-II 48/5000/70-50 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 5000 w power at non-linear load 4000 w continuous load and 9000 w peak power for 48 v battery voltage, 50 a transfer switch and 70 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482505010 Multiplus-II 48/5000/70-50a 1x user manual

In this plastic housing (mpn ass050400000) you can install your Color Control gx in an elegant and safe way. In addition to the significantly improved protection of the electronics from moisture, the housing also offers other advantages in terms of installation safety. The cables are led through an opening and can still be strain-relieved in the housing Compatible with Victron Color Control gx Scope of delivery1x Victron ass050400000 Housing Color Control gx

Color Control GXThe Color Control (CCGX) provides intuitive control and monitoring for all products connected to it. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, all our latest MPPT solar chargers, BMV-700, BMV-600, Lynx Ion+ Shuntand more. VRM Online PortalBesides monitoring and controlling products on the CCGX, the information is also forwarded to the free remote monitoring website: the VRM Online Portal. To get an impression of the VRM Online Portal, visit https://vrm.victronenergy.com, and try the demo. See also the screenshots in the datasheet.Future functionalityThe CCGX has endless possibilities. To implement all the ideas and wishes will take years. There are therefore many features that are not yet available. Functions marked with ‘Future function’ will become available later on, as a firmware update. Firmware updates are free of charge, as with all updates of Victron products. Updating the product is easy: the CCGX will update itself automatically, as long as it is connected to the internet. Manual updates can be done with a USB stick and microSD cards.Supported products Multis and Quattros, including split phase and three-phase systems. Monitoring and control (on/off and current limiter). Changing settings is not yet available. BlueSolar MPPT 150/70 and the MPPT 150/85. Current solar output is visible on the overview screen, and all parameters are logged to the VRM online portal. Note that the VRM App has a nice overview showing data of the BlueSolar MPPT 150/70 as well. When multiple BlueSolar MPPTs with VE.Can are used in parallel, the Color Control will show all information as one. BlueSolar MPPT Solar Chargers with a VE.Direct port (70/15, 75/15, 100/15, 100/30, 75/50, 100/50, 150/35) can be connected to the VE.Direct ports on the CCGX. Connecting multiple at the same time is possible. They will all appear as a separate Solar Charger in the device list. BMV-700 family can be connected directly to the VE.Direct ports on the CCGX. Use the VE.Direct Cable for this. BMV-600 family can be connected to the VE.Direct ports on the CCGX. Use the VE.Direct to BMV60xS cable for that. Lynx Ion + Shunt Lynx Shunt VE.Can Skylla-i NMEA2000 tank sensors A USB GPS can be connected to the USB port. Location and speed will be visible on the display, and the data is sent to the VRM Portal for tracking purposes. The map on VRM will show the latest position. WiFi USB.  Note that there are more options for products which use the VE.Direct ports, such as BMVs and small MPPTs. They can also be connected through USB, useful when more than two products need to be connected. Use an off-the-shelf USB-hub and the VE.Direct to USB interface, ASS030530000.Other highlightsWhen connected to the internet, the CCGX will update itself automatically when there is a new software version available.Multiple languages: English, Chinese, German, Italian, Spanish, French, Swedish and Dutch.Use the CCGX as a Modbus-TCP gateway to all connected Victron products.Notes for existing VGR2 and VER usersOpposite to the Victron Global Remote 2 (VGR2) and Victron Ethernet Remote (VER), the CCGX stores all data locally during network interruptions. As soon as the connection to the VRM Online Portal is restored, it will automatically send all backlogged data to the portal. Data can then be analysed on https://vrm.victronenergy.com. The local website, as present on the VER, is not yet supported.The CCGX has no internal GPRS modem: you cannot insert a sim-card into the CCGX. Use an off-the-shelf GPRS or 3G router instead.

The Multiplus-II 12/3000/120-32 is a high-end device combination from victron Energy (mpn pmp122305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and the potential range of use to ESS applications. The inverter module delivers a whopping 3000 w at non-linear load, or 2400 w at linear continuous load. the 12 v battery charger is also very well proportioned, with 120 a charging power, and is complemented by a 32 a transfer switch that allows lightning-fast switching between aC connections. important features of the Multiplus-II 12/3000/120-32 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* Technical features 3000 w power at non-linear load 2400 w continuous load and 5500 w peak power for 12 v battery voltage, 32 a transfer switch and 120 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 12/3000/120-32. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In case of grid failure or interruption of shore/generator power, the MultiPlus-II takes over the supply of the connected loads. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp122305010 Multiplus-II 12/3000/120-32a 1x user manual

The Multiplus-II 48/8000/110-100 is a high-end device combination from victron Energy (mpn pmp482805000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and the potential range of use to ess applications. The inverter module delivers a whopping 8000 w at non-linear load, or 6400 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 110 a charging power, and is complemented by a 100 a transfer switch that allows lightning-fast switching between aC connections. important features of the Multiplus-II 48/8000/110-100 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 8000 w power at non-linear load 6400 w continuous load and 15000 w peak power for 48 v battery voltage, 100 a transfer switch and 110 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/8000/110-100. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482805000 Multiplus-II 48/8000/110-100a 1x user manual

The victron MultiPlus 12/3000/120-50 (MPN PMP123021010) is a combination of 12V 2400W inverter and battery charger. The integrated battery charger provides 120A which allows quick charging even for bigger batteries as long as there is a grid connection.The 12V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Besides those two components there is also an integrated transfer-switch that enables you to realize many grid-tied solutions.Integrating the MultiPlus in your system can be done via VE.Bus-port or COM-port which allows nearly unlimited networking. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 50A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 2400W constant output and 6000W peak current, for 12V battery voltage combination of inverter with transfer switch and 120A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available Besides the VE.Bus-port MultiPlus devices 3000 or bigger additionally come with an COM-port the allows nearly unlimited system integration PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) thanks to the integrated transfer-switch with 16A or 50A usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron PMP123021010 Multiplus 12/3000/120-50 Combination of 12V 2400W sine inverter and 12V 120A battery charger + transfer-switch1x Manual  

The MultiPlus 12/500/20-16 (pmp121500000) from Victron Energy is a slimmed down version of the successful Multiplus Series and provides 500w of continuous power at 230v and 50Hz. Besides the sine wave voltage converter that converts the 12v dc voltage of your battery into a perfect 230v ac 50Hz sine wave voltage, the Multi 500 is also equipped with a 20a strong battery charger and a 16a transfer switch. This makes it very interesting for a wide range of applications and at a comparatively very reasonable price. essential features of the Multi 12/500/20 500w continuous power and 900w peak power, for 12v battery voltage Device combination sine wave voltage converter, 16a transfer switch and 20a battery charger provides purest 230v sine wave voltage and a clean 50Hz frequency thanks to transfer switch can be used as usv solution for uninterruptible power supply can be used for grid connected self-consumption systems that only draw power from the grid operator when battery capacity is insufficient or other programmable events have occurred programmable relay proven quality and reliability provides solid protection against overload and overheating versatile in mobile and stationary applications can also be used for highly sensitive electrical equipment applicable in usv solutions programmable relayThe Multi 12/500/20 has a programmable multi-function relay which operates as an alarm relay in the basic setting. However, this relay can be programmed for a variety of additional functions, such as a start relay for a generator Control and remote operabilityThe configuration takes place via a 3-position switch (DIP switch) directly on the multi. the maximum charging current strength of the AC input can be set. A VE.Bus or other communication ports as in the Multiplus series have been omitted.Lightning-fast, automatic 16a transfer switchIn the event of a power supply interruption or generator shutdown, Multi immediately switches to inverter mode to supply the connected loads. This happens so fast (less than 20 milliseconds) that e.g. the operation of computers or other electronic equipment continues without interruption (uninterruptible power supply - ups functionality) powerful 4-stage battery chargerAdaptive 4-stage charging characteristics: constant current ("bulk") phase, constant voltage ("absorption") phase, charge retention voltage ("float") phase, storage voltage ("storage") phaseThe battery charging system is controlled by microprocessors and can be adapted to different battery types. The charging process is adapted to the battery usage by adaptive control other highlights of the consumed charger include: variable constant voltage time 2 DC outputs for charging board and starter battery Extended battery life due to temperature compensation less battery aging due to integrated storage mode less harmful gas formation due to battery save mode For a detailed description of the charger's performance, please refer to the user manual which you can find under "Downloads" above.BackUp system: alternating current even in case of power failure The Multi 500 can be used in non-grid connected applications as well as in grid connected PV systems or alternative energy systems. Software is available to detect a grid failure. What is the difference between the Multi 500 and the Multi(Plus) 800 and Multiplus series? To clarify the differences, here is a small table that contains the criteria in which the device families Multi(Plus) and Multiplus differ Distinguishing features of the 3 Multi families Multi 500 Multi(Plus) Multiplus 2 ac outputs - - Yes Parallel connection of multiple devices - Yes Yes Series connection of multiple devices - - Yes completely remote controllable - - Yes VE.Bus connection - - Yes PowerAssist function - Yes Yes PowerControl function - Yes Yes Scope of deliveryg1x Victron Multi cmp125010000 12/500/20 1x instruction manual

The victron MultiPlus C 24/2000/50 (MPN CMP242020000) is a combination of 24V 1600W inverter and battery charger. The integrated battery charger provides 50A which allows quick charging even for bigger batteries as long as there is a grid connection.The 24V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 30A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 1600W constant output and 4000W peak current, for 24V battery voltage combination of inverter with transfer switch and 50A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron CMP242020000 Multiplus C 24/2000/50 Combination of 24V 1600W sine inverter and 24V 50A battery charger1x Manual

The Victron Digital Multi Control Panel (MPN DMC000200010R) is a remote control panel for MultiPlus and Quattro inverters and grounds on the VE.Bus-technology. It allows the configuration of PowerControl and PowerAssist power-limitation for two AC-sources, for example generator or shore-power. Setting range: up to 200A.Moreover it can be used as on-/off-switch for connected devices. The LEDs' luminosity is reduced automatically during night-time. The DMC is a remote control panel for als Multis or Quattros and for all systems where a Multi or Quattro is integrated. This includes single devices, parallel operation and multiphase-operation.It supports either VE.Bus-systems but also systems without it. The DMC allows the separate adjustment of generator- and shore-power. When installed in an extended VE.Bus-system up to four different shore-power sources can be adjusted.Within a VE.Bus-system the DMC will choose the right setting range for your system automatically. Delivery scope:1x Victron DMC000200010R Digital Multi Control Panel for Multiplus and Quattro inverters1x Manual

The victron MultiPlus 24/5000/120-100 (MPN PMP245021010) is a combination of 24V 4000W inverter and battery charger. The integrated battery charger provides 120A which allows quick charging even for bigger batteries as long as there is a grid connection.The 24V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Besides those two components there is also an integrated transfer-switch that enables you to realize many grid-tied solutions.Integrating the MultiPlus in your system can be done via VE.Bus-port or COM-port which allows nearly unlimited networking. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 100A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 4000W constant output and 10.000W peak current, for 24V battery voltage combination of inverter with transfer switch and 120A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available Besides the VE.Bus-port MultiPlus devices 3000 or bigger additionally come with an COM-port the allows nearly unlimited system integration PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) thanks to the integrated transfer-switch with 16A or 50A usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron PMP245021010 Multiplus 24/5000/120-100 Combination of 24V 4000W sine inverter and 24V 100A battery charger + transfer-switch1x Manual  

The Multiplus-II 24/5000/120-50a is a high-end device combination from victron Energy (mpn pmp242505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 24 v battery charger is also very well proportioned, with 120 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections. important features of the MultiPlus-II 24/5000/120-50 PowerControl and Powerassist -increase mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software Technical features 5000 w power at non-linear load 4000 w continuous load and 9000 w peak power for 24 v battery voltage, 50 a transfer switch and 120 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 24/5000/120-50. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In case of grid failure or interruption of shore/generator power, the MultiPlus-II takes over the supply of the connected loads. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp242505010 Multiplus-II 24/5000/120-50a 1x user manual

The new MultiPlus 24/800/16-16 (Victron Energy, pmp241800000) is the successor to the Multiplus Compact 24/800. This unit is an advanced device combination consisting of a powerful pure sine wave inverter, an advanced 16a battery charger utilizing adaptive charging technology, and a 16a high speed AC transfer switch. In the event of a mains fault or, if shore power or on-board generator is interrupted, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. main features of the MultiPlus 24/800/16-16 Cont. Output power at 25°c: 700w / 800w at non-linear load Victron Energy mpn: pmp241800000 for 24v system voltage integrated 16a mains charger for your batteries integrated 16a mains transfer switch USV operation possible Extensive accessories available Can be used in numerous applications, whether on land or mobile proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature) PowerControl - (Multiplus 800va 1200va only) The Multi Control remote control panel can be used to set the maximum mains or generator current to be drawn. The MultiPlus then takes into account other connected AC loads and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded PowerAssist - (Multiplus 800va 1200va only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries High switch-on power This is required for switching on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the Multi will turn off at zero load or low load and turn back on every two seconds for a short period of time. if the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again programmable relay In the basic setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low) Scope of delivery: Victron Energy pmp241800000, MultiPlus 24/800/16-16

The new MultiPlus 12/800/35-16 (Victron Energy, pmp121800000) is the successor to the Multiplus Compact 12/800. This unit is an advanced device combination consisting of a powerful pure sine wave inverter, an advanced 50a battery charger utilizing adaptive charging technology, and a 16a high speed AC transfer switch. In the event of a mains fault or, if shore power or on-board generator is interrupted, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. main features of the MultiPlus 12/800/35-16 Cont. Output power at 25°c: 700w / 800w at non-linear load Victron Energy mpn: pmp121800000 for 12v system voltage integrated 35a mains charger for your batteries integrated 16a mains transfer switch USV operation possible Extensive accessories available Usable in numerous applications, whether on land or mobile proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature) PowerControl - (Multiplus 800va 1200va only) The Multi Control remote control panel can be used to set the maximum mains or generator current to be drawn. The MultiPlus then takes into account other connected AC loads and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded PowerAssist - (Multiplus 800va 1200va only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries High switch-on power This is required for switching on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the Multi will turn off at zero load or low load and turn on again every two seconds for a short period of time. if the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low) Scope of delivery: Victron Energy pmp121800000, MultiPlus 12/800/35-16

The Multiplus-II 48/5000/70-50 gx is a high-end device combination from victron Energy (mpn pmp482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and expands the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 70 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections. Compared to the rest of the series, the gx variants have an integrated gx display with numerous other connection options. important features of the Multiplus-II 48/5000/70-50 gx integrated gx control unit with various communication ports PowerControl and Powerassist -increase of mains or generator power built-in anti-islanding function and connection for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 5000w power at non-linear load 4000 w continuous load and 9000 w peak power for 48 v battery voltage, 50 a transfer switch and 70 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50 gx. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. Scope of the integrated gx device A vE.Can interface This can be used to connect vE.Can devices from victron (e.g. vE.Can mppt). The port can also be reconfigured via the remote console for use with a compatible CaN-Bus Li-Ion battery. 1xUSB connection 1x Ethernet port 1x vE.Direct connection many possibilities for system expansion Settings can be changed within minutes using the vEConfigure software (requires a computer or laptop and MK3 USB interface).multiple monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482506000 Multiplus-II 48/5000/70-50 gx 230v 1x instruction manual

Der Multiplus-II 24/3000/70-32 GX ist eine High-End Gerätekombination von Victron Energy (MPN PMP242306000), die klassische Multiplus-Komponenten mit einem extrem leistungsstarken Sinuswechselrichter, ein Batterieladegerät und ein Transferschalter in einem kompakten Gehäuse zusammenführt. Dadurch werden die Funktionen PowerControl und PowerAssist auf 50 A erweitert und der potenzielle Einsatzbereich auf ESS-Anwendungen ausgedehnt. Das Wechselrichter Modul leistet bei nicht linearer Belastung satte 3000 W, bzw. 2400 W bei linearer Dauerbelastung. Auch das 24 V Batterieladegerät ist mit 70 A Ladeleistung sehr gut proportioniert und wird durch einen 32 A Transferschalter ergänzt, mit dem sich blitzschnell zwischen den AC-Anschlüssen hin- und herschalten lässt. Wichtige Leistungsmerkmale des Multiplus-II 24/3000/70-32 GX PowerControl und PowerAssist –Steigerung von Netz-oder Generator-Leistung GX LCD-Anzeige (hintergrundbeleuchtende Anzeige) BMS-Can-Anschlüsse Ethernet und WLAN Automatische unterbrechungsfreie Umschaltung kann als Backupgerät in netzgekoppelten Anlagen eingesetzt für die Stromversorgung bei Netzausfällen einsetzbar in verschiedenen ESS (Energy Storage System) Anwendungen bestens geeignet für die professionelle Seefahrt, Yachten, Fahrzeuge und landgebundene, netzferne Anwendungen VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb, Fernüberwachung und Systemintegration praktisch unbegrenzte Leistung durch Parallel-und Drei-Phasen-Betrieb kann vor Ort oder aus der Ferne mittels VEConfigure Software konfiguriert werden* Immer genug Power dank PowerControl und PowerAssist Am Multiplus-II 24/3000/70-32 GX kann ein maximaler Netz- oder Generatorstrom eingestellt werden. Der MultiPlus-II GX nimmt somit Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden der Batterie nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Netzanschluss überlastet wird (PowerControl-Funktion). Mit der Funktion PowerAssist erhält das PowerControl-Prinzip eine neue Dimension. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall kompensiert das MultiPlus-II GX zu schwache Generator-, Landstrom- bzw. Netzleistung sofort durch Energie aus der Batterie. Wird die Last reduziert, d. h. werden Verbraucher ausgeschaltet, kann die dann wieder ausreichend vorhandene Energie zum Laden der Batterien genutzt werden. Solarstrom: Wechselstrom auch bei Netzausfall Das Gerät kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es lässt sich sowohl mit Solar-Lade-Reglern als auch mit netzgebundenen Wechselrichtern verwenden. Maximale Flexibilität dank zweier Wechselstromausgänge Der Hauptausgang stellt einen unterbrechungsfreien Betrieb sicher. Im Falle eines Netzausfalls oder bei einer Unterbrechung des Land-/Generatorstroms übernimmt der MultiPlus-II GX die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet ist. Der zweite Ausgang liefert nur dann Strom, wenn am Eingang des MultiPlus-II GX Wechselstrom verfügbar ist. Verbraucher, die die Batterie nicht entladen dürfen, wie z. B. ein Wassererhitzer, können an diesen Ausgang angeschlossen werden. Viele Möglichkeiten zur Systemerweiterung Die Einstellungen lassen sich mit der VEConfigure Software binnen weniger Minuten ändern (es ist dafür ein Computer oder Laptop und ein MK3-USB-Interface notwendig).Es stehen mehrere Überwachungs- und Steuerungs-Optionen zur Verfügung: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (mit dem optionalen VE.Bus Smart Dongle), Batterie-Wächter, Digital Multi Bedien-Paneel. Remotekonfiguration und -überwachung Installieren Sie einen Cerbo GX oder ein anderes GX-Produkt, um eine Verbindung zum Internet herzustellen. Betriebsdaten können kostenlos auf unserer VRM-Website (Victron Remote Management) gespeichert und angezeigt werden. Wenn Sie mit dem Internet verbunden sind, kann aus der Ferne auf Systeme zugegriffen und Einstellungen geändert werden. Weiter GX-Optionen stehen Ihnen beispielsweise zur Verfügung: Victron Color Control GX Victron Venus GX Systemüberwachung BPP900400100 Technische Merkmale: Abmessungen: 506 x 275 x 147 mm Gewicht: 19 kg Leistung: 3000 W bei nicht linearer Belastung, 2400 W Dauerbelastung und 6000 W Spitzenleistung Ausgangsspannung: 230 VAC Frequenz: 50 Hz max. Wirkungsgrad: 95% Schutzklasse IP22 Lieferumfang: 1x Victron Multiplus-II 24/3000/70-32 GX 1x Bedienungsanleitung

The victron MultiPlus C 24/1200/25 (MPN CMP241220000) is a combination of 24V 1000W inverter and battery charger. The integrated battery charger provides 25A which allows quick charging even for bigger batteries as long as there is a grid connection.The 24V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 16A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 1000W constant output and 2400W peak current, for 24V battery voltage combination of inverter with transfer switch and 25A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron CMP241220000 Multiplus C 24/1200/25 Combination of 24V 1000W sine inverter and 24V 25A battery charger1x Manual

The victron MultiPlus C 12/1600/70 (MPN CMP121620000) is a combination of 12V 1300W inverter and battery charger. The integrated battery charger provides 70A which allows quick charging even for bigger batteries as long as there is a grid connection.The 12V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 16A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 1300W constant output and 3000W peak current, for 12V battery voltage combination of inverter with transfer switch and 70A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron CMP121620000 Multiplus C 12/1600/70 Combination of 12V 1300W sine inverter and 12V 70A battery charger1x Manual

Der Multi RS Solar 48/6000/100-450/100 Dual (MPN PMR482602020) aus der renommierten Produktpalette von Victron Energy kombiniert die Funktionen eines Hybrid-Wechselrichters und eines Batterieladegeräts in einer äußerst leistungsstarken Gerätekombination, um deinen Energiebedarf effizient und zuverlässig zu erfüllen. Mitte 2023 wurde der ursprüngliche Single-MPPT-Tracker zu diesem Dual-MPPT-Tracker-Modell mit zwei unabhängigen MPPT-Tracker-Eingängen für insgesamt 6 kWp PV-Leistung weiterentwickelt. Dank Hochfrequenztechnik und neuem Design wiegt die leistungsstarke Gerätekombination nur 11 kg, verfügt über einen ausgezeichneten Wirkungsgrad, eine geringe Standby-Leistung und ist außerdem sehr leise im Betrieb. Dual-Modell mit 4 Betriebsarten Hybrid-Modus: Speichert überschüssige Solarenergie in einer Batterie, um sie in der Nacht oder in Zeiten hoher Nachfrage zu nutzen. Liefert zusätzlichen Strom aus der Batterie, wenn der Bedarf die Netzkapazität übersteigt. Reserve-Modus: Schaltet während eines Netzausfalls in den Reservemodus. Netzunabhängiger Modus: Funktioniert ohne Netzanschluss. Generator-Modus: Steuert den Generator, um die Laufzeit zu minimieren. Liefert zusätzlichen Strom aus der Batterie, wenn der Bedarf die Kapazität des Generators übersteigt. Der Victron Multi RS Solar Hybrid Wechselrichter/Ladegerät Dual-MPPT-Tracker und 6000 VA Leistung Effiziente Batterieladung, Pulsweitenmodulation (PWM) Schutzfunktionen: Gerätesicherung FKS MasterBus-Kompatibel: Integration in Energiemanagementsysteme Vielseitige Anwendungen Programmierbares Relais Energieoptimierung durch Rückeinspeisung Benutzerfreundliches, intuitives Display Leistungsstark und Flexibel Die hochmoderne Gerätekombination bietet eine beeindruckende Spitzenleistung von 6000 VA (Watt), welche selbst anspruchsvolle Anwendungen wie die Stromversorgung von Haushaltsgeräten, Büroausrüstungen oder Elektrofahrzeugen bewältigt. Sie bietet nicht nur eine zuverlässige Stromversorgung, sondern ermöglicht es dir auch, überschüssige Energie in die Batterien zurückzuspeisen und so den Eigenverbrauch zu erhöhen. Mit einer Eingangsspannung von 48 V und einem Ladestrom von 100 A ermöglicht dieses Gerät eine schnelle und effiziente Aufladung deiner Batterien. Die integrierte Pulsweitenmodulation (PWM) für die Ladespannungsregelung stellt die optimale Ladung deiner Batterien sicher, während die Gerätesicherung FKS (Fast-Blow Fuse) das Gerät und dein Energiesystem vor Überlastung und Kurzschlüssen schützt. PowerControl und PowerAssist Die PowerControl-Funktion begrenzt den maximalen Netz- oder Generatorstrom, um den Multi RS dazu zu bringen, Rücksicht auf andere AC-Lasten zu nehmen. Dadurch nutzt er dann nur überschüssigen Strom zum Laden der Batterie, wodurch Überlastungen vermieden werden. Die PowerAssist-Funktion sorgt dafür, dass Batterien während kurzzeitiger Lastspitzen sofort unterstützen und bei reduzierter Last aufgeladen werden. Einfache Bedienung und Überwachung Mit einem benutzerfreundlichen Display und einer intuitiven Benutzeroberfläche kannst du den Betriebsstatus und die Einstellungen, sowie die Batterie-, Wechselrichter- und Solarparameter, des Victron Multi RS Solar 48/6000/100-450/100 Dual leicht überwachen und anpassen. Dank der MasterBus-Kompatibilität kannst du das Gerät nahtlos in ein intelligentes Energiemanagementsystem integrieren und mit einem Smartphone oder einem anderen Bluetooth-fähigen Gerät über die VictronConnect-App auch mehrere Geräte zentral steuern. Technische Daten: Wechselrichter: DC-Eingangspannungsbereich: 38-62 V AC-Ausgangsspannung: 230 VAC ± 2 % Frequenz: 50 Hz ± 0,1 % max. Dauerstrom: 25 A AC max. Ausgangsleistung: 5300 W bei 52 VDC Spitzenleistung: 9 kW für 3 s / 7 kW für 4 min Kurzschlussausgangsstrom: 45 A max. Überstromschutz des Wechselstromausgangs: 30 A Wirkungsgrad:  96,5 % bei 1 k W Last Solar: max. PV-Lerspannung: 450 V Anlaufspannung: 120 V MPPT-Betriebsspannungsbereich 80-450 V max. betriebliche PV-Eingangsstrombegrenzung: 13 A max. PV-Umwandlungsleistung: insg. 6 kW - 3kW pro Tracker max. PV-Kurzschlussstrom: 16 A Erdschlussauslösepegel: 30 mA Isolationsausfallpegel: 100 kΩ Ladegerät: Nennspannung: 230 VAC Eingangsspannungsbereich: 187-265 VAC Nennfrequenz: 50 Hz Eingangsfrequenz: 45-65 Hz AC-Einschaltstrom: N.z. programmierbarer Ladespannungsbereich: 36-60 V Ladespannung "Konstantspannung": 57,6 V (verstellbar) "Erhaltungs"-Ladespannung: 55,2 V (verstellbar) max. Ladestrom von AC: 88 A @ 57,6 VDC max. Ladestrom insg. (AC+PV): 100 A Gleichstrom Batterietemperatursensor: mitgeliefert Batteriespanungssensor: ja Allgemeines: Zusatzausgang (AC-out-2): ja Drei-Phasen- und Parallel-Betrieb: 2x 2023 Q4 Anschlüsse: VE.Direct, VE.Can & Bluetooth Bluetooth-Frequenz und -Leistung: 2402–2480 Mhz, 4 dBm Betriebstemperaturbereich -40 bis +65 °C Maximale Höhe 2000 m Luftfeuchtigkeit: max. 95 %  nicht kondensierend Schutzklasse: IP21 Batterieanschluss: M8-Bolzen PV-Verbindung: 2 Strings mit MC4 230VAC-Anschluss: Schraubklemmen 10 mm² (6 AWG) Abmessungen: 425 × 460 × 125 mm Gewicht: 12,3 kg Lieferumfang: 1× Victron Multi RS Solar 48/6000/100-450/100 Dual

The new MultiPlus 48/800/9-16 (Victron Energy, pmp481800000) is the successor to the Multiplus Compact 48/800. This unit is an advanced device combination consisting of a powerful pure sine wave inverter, an advanced 9a battery charger utilizing adaptive charging technology, and a 16a high speed AC transfer switch. In the event of a mains fault or, if shore power or on-board generator is interrupted, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. main features of the MultiPlus 48/800/9-16 Cont. Output power at 25°c: 700w / 800w at non-linear load Victron Energy mpn: pmp481800000 for 48v system voltage integrated 9a mains charger for your batteries integrated 16a mains transfer switch USV operation possible Extensive accessories available Can be used in numerous applications, whether on land or mobile proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature) PowerControl - (Multiplus 800va 1200va only) The Multi Control remote control panel can be used to set the maximum mains or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded PowerAssist - (Multiplus 800va 1200va only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries High switch-on power This is required for switching on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools Search mode When the search mode is set to 'on', the current consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the Multi will shut down at zero load or at only light load and turn back on for a short period every two seconds. if the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low) Scope of delivery: Victron Energy pmp481800000, MultiPlus 48/800/9-16

The Victron MultiPlus C 12/2000/80 (MPN CMP122020000) is a combination of 12V 1600W inverter and battery charger. The integrated battery charger provides 80A which allows quick charging even for bigger batteries as long as there is a grid connection.The 12V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 30A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 1600W constant output and 4000W peak current, for 12V battery voltage combination of inverter with transfer switch and 80A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron CMP122020000 Multiplus C 12/2000/80 Combination of 12V 1600W sine inverter and 12V 80A battery charger1x Manual  

The Multiplus 24/2000/50-32 from Victron (mpn pmp242200000) is a device combination of 24v 2000w sine wave inverter and battery charger. The integrated battery charger has an output of 50a, which means that even large batteries can be fully charged quickly if shore power is available. The 24v sine wave voltage converter built into the Multiplus converts your current from the battery to 230v AC. Thanks to the true sine wave, the power quality is perfect even for sensitive electronic devices. In addition to the two integrated device types, a lightning-fast 32a transfer switch is also built in, which can also be used to implement numerous grid-connected solutions. For system integration, the MultiPlus has a VE.Bus port, which enables virtually unlimited networking. Comprehensive and flexible use Since it has a lightning-fast 32a transfer switch in addition to the inverter and charger, it is an ideal inverter for motorhome, boat or yacht applications and the grid-connected area of uninterruptible power supply in the event of grid fluctuations or power outages. Also for use in grid-connected self-consumption systems that only draw power from the utility when the battery power is no longer sufficient or as a usv solution in which the Multiplus step in when the power from the grid operator suddenly fails and thus provide an uninterrupted power supply. Key features of the Multiplus 24/2000/50-32 1600W continuous power and 3500w peak power, for 24v battery voltage Device combination of inverter with transfer switch and 50a battery charger delivers purest 230v sine wave voltage and a clean 50Hz frequency VE.Bus communication port provides extensive networking, system integration, configuration and control of Multiplus devices from Victron supports three-phase operation (3 identical units of the same model required) Multiplus units can be connected in parallel, up to 6 units can be connected in parallel, significantly increasing system performance when needed PowerControl function allows working with limited generator power as well as limited shore or grid power PowerAssist function enables "power increase" of generators and shore power support in case of need can be used as usv solution for uninterruptible power supply, thanks to the integrated transfer switch can be used for grid-connected self-consumption systems that draw power from the grid operator only when battery capacity is insufficient or other programmable events have occurred compatible with numerous Victron control and display panels Massive power expansion possible Apart from the parallel connection, three units of the same model can also be configured for three-phase output. But that's not all: up to six sets of three units can be connected in parallel to achieve a huge charging capacity PowerControl - working with limited generator power, limited shore or mains power The MultiPlus is a very powerful battery charger. Therefore, it draws a lot of power from the generator or shore power. The Multi Control remote control panel can be used to set the maximum shore or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist - "power enhancement" of generators and shore power support This function adds a new dimension to the PowerControl principle. It enables the MultiPlus to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that shore power or generator output that is too weak is immediately compensated for by energy from the battery. BackUp system: alternating current even in the event of a power failure The Multiplus can be used with both non-grid-connected and grid-connected PV systems, as well as with other alternative energy systems. Software is available to detect a grid failure. Simple system configuration If settings need to be changed on a single device, this can be done in minutes using a DIP switch setting procedure. Parallel connected and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software. monitoring options and on-site control Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (usb or RS232). remote monitoring and control Victron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. In addition, system data can be stored and viewed free of charge on the vrm (Victron Remote Management) website. Remote configuration If systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely. Scope of delivery: 1x Victron pmp242200000 Multiplus 24/2000/50-32 device combination consisting of 24v 2000w sine wave converter + 24v 50a battery charger + 32a transfer switch 1x user manual

The Victron Digital Multi Control Panel (MPN DMC000200010R) is a remote control panel for MultiPlus and Quattro inverters and grounds on the VE.Bus-technology. It allows the configuration of PowerControl and PowerAssist power-limitation for two AC-sources, for example generator or shore-power. Setting range: up to 200A.Moreover it can be used as on-/off-switch for connected devices. The LEDs' luminosity is reduced automatically during night-time. The DMC is a remote control panel for als Multis or Quattros and for all systems where a Multi or Quattro is integrated. This includes single devices, parallel operation and multiphase-operation.It supports either VE.Bus-systems but also systems without it. The DMC allows the separate adjustment of generator- and shore-power. When installed in an extended VE.Bus-system up to four different shore-power sources can be adjusted.Within a VE.Bus-system the DMC will choose the right setting range for your system automatically. Delivery scope:1x Victron DMC000200010R Digital Multi Control Panel for Multiplus and Quattro inverters1x Manual