The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 15a max charge current for charging 12v and 24v batteries. Unlike the Bluesolar 75/15, the Smart version has integrated Bluetooth, which eliminates the need to purchase a Bluetooth dongel. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control gx or the mppt Control. The integrated Bluetooth in the SmartSolar series is the wireless solution to setup, monitor and update the controller using Apple and Android smartphones, tablets or other devices. The most important technical features at a glance 15a max. charging current, suitable for 12v and 24v batteries nominal PV power for 12v systems: 220W nominal PV power for 24v systems: 440W 15a load output high peak efficiency of 98% freely programmable battery charging algorithm (via the free Victron Connect APP) Light dimming functions programmable (via the free Victron Connect APP) Ultra fast maximum power point tracking max. PV open circuit voltage: 75V Charging algorithm: multi-stage, adaptive integrated Bluetooth modu Ultra fast maximum power point tracking Especially in overcast conditions when light intensity is constantly changing, an ultra-fast mppt controller improves power output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers. intelligent load output Deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an algorithm for intelligent battery management can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within a day, the status of the battery will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charging) will damage a lead-acid battery within a few weeks or months. The Battery-Life algorithm monitors the battery's state of charge and, if necessary, raises the load disconnect threshold day by day (i.e., disconnects the load earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point, the load disconnection threshold is modulated so that charging to near 100% is achieved about once a week. Scope of delivery: 1x Victron EnergySCC075015060R Smartsolar mppt 75/15 15a 12v 24v solar charge controller 1x user manual

The Smartsolar 100/20-48 from Victron Energy (mpn scc110020160r) is a mppt solar charge controller with 20a max charge current for charging 12v and 24v batteries. Unlike the Bluesolar version, the Smart version has integrated Bluetooth, which eliminates the need to purchase a Bluetooth dongel. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control gx or the mppt Control. The integrated Bluetooth in the SmartSolar series is the wireless solution to setup, monitor and update the controller using Apple and Android smartphones, tablets or other devices. The most important technical features at a glance 20a max. charging current, suitable for 12v and 24v batteries nominal PV power for 12v systems: 290W nominal PV power for 24v systems: 580W nominal PV power for 48v systems: 1160W 20a load output high peak efficiency of 98 freely programmable battery charging algorithm (via the free Victron Connect APP) Light dimming functions programmable (via the free Victron Connect APP) Ultra fast maximum power point tracking max. PV open circuit voltage: 100V Charging algorithm: multi-stage, adaptive integrated Bluetooth module Ultra fast maximum power point tracking Especially in overcast conditions when light intensity is constantly changing, an ultra-fast mppt controller improves power output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers. intelligent load output Deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an algorithm for intelligent battery management can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within a day, the status of the battery will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charging) will damage a lead-acid battery within a few weeks or months. The Battery-Life algorithm monitors the battery's state of charge and, if necessary, raises the load disconnect threshold day by day (i.e., disconnects the load earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point, the load disconnection threshold is modulated so that charging to near 100% is achieved about once a week. Scope of delivery: 1x Victron Energy Smartsolar mppt 100/20-48 20a 12v 24v 48v solar charge controller 1x instruction manual Note The device shows the imprint 48v - on the packaging of the device the data sheet of the 48v version is printed on the side. Contrary to this confusing information on the device itself, this is as described for both 12v and 24v - and now also suitable for 48v battery banks. Until recently these were separate devices - one for 12v/24v and one for 48v - these two have now been combined and the printing on the case and packaging has been taken from the 48v version

The Victron MPPT 75/15 (MPN SCC010015050R) is part of the BlueSolar MPPT charge controller familiy and provides ultra-fast powertracking which extends your solar system's output. Next generation MPP-tracker Especially on clouded days with changing light intensity a MPPT controler increases your system output by up to 30% compared to PWM charge controllers. Moreover the 75/15 comes with further innovative technologies. Programming, real-time data and logging Latest Apple and Android devices (smartphones, tablets,...) can be connected via VE.Direct over Bluetooth Smart Dongles and the MPPT App or via the GX Color control. Please note that the Bluetooth Smart dongle and the GX Color Control are not included in the delivery scope but available separately. Important features: Ultra-fast MPP-tracker ensures highest possible outcome even when it is cloudy Integrated VE.Direct data port for connecting devices like the Bluetooth Smart Dongle or the GX Color Control panel Suitable for 12V and 24V systems Rated charging amperage: 15A 200W max. PV-performance at 12V and 400W at 24V 15A consumer output with auto-shutdown at imminent battery undervoltage (deep discharge protection) Reverse polarity protection Multistep adaptive charging algorithm Battery charging algorithm programmable Integrated battery life algorithm extends battery life when activated and all consumers are connected to the consumer output Day/night-time control and dimming options VE.Direct data port integrated VE.Direct transfers important parameters to all devices connected to the charge controller and allows communication to equipment such as the Bluetooth Smart Dongle or the GX Color Control. The VE.Direct data port is meant for products where a full canbus integration would produce extreme costs. Please check our Victron brand section for more information about VE.Direct. Integrated battery life algorithm extends battery life If the charge controller can't manage to fully charge the battery within a day the battery status switches constantly between "partly charged" and "end of discharge". This operation mode (no regular charging) is ideal for small lead batteries, for lead-acid batteries otherwise irregular charging and discharging can cause severe damage already after several months. The battery life algorithm checks the battery's charging level and heightens the switch-off threshold from day to day. That means that connected consumers are switched off earlier until the produced energy is sufficient for a full battery charge of 100%. From this point on the threshold is modulated in a way that a full charge can be reached once a week. Delivery Scope: 1x Victron SCC010015050R BlueSolar MPPT 75/15 12V 24V 15A charge controller 1x Manual

The Victron Energy SmartSolar mppt 100/30 30a 12v/24v solar charge controller (mpn scc110030210), is new version of the BlueSolar 100/30. The Smart version differs only in the from the Blue version mainly by the permanently integrated Bluetooth communication module. This allows the SmartSolar charge controller to be fully monitored and analyzed on any app-enabled device. The required Victron Connect app can be installed free of charge. key product features of the SmartSolar 100/30 30a 12v 24v mppt latest generation ultra-fast MPP tracker ensures best possible yield even in overcast conditions integrated VE.Direct data communication port high maximum efficiency of 98 for 12v and 24v systems integrated Bluetooth module 30a maximum charge current fully programmable charging algorithms that can later be manually activated and used via a switch on the case 100V maximum pv open circuit voltage 440W maximum pv power for 12v, 880w for 24v systems integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Day/night time control and light dimming option more protection compared to the smaller models in the SmartSolar mppt seriesCompared to the 75/10, 75/15 and 100/15 model, the SmartSolar 100/30 mppt has overheating protection with shutdown function and automatic restart after reaching normal operating temperature VE.Direct data communication port VE.Direct in text mode transmits all important parameters to other devices linked to the charge controller every second, providing the possibility of communication with additional devices gx Color Control Panel from Victron. The VE.Direct connection is intended for products where a full Canbus integration (VE-Direct) would cause too high costs High-speed MPP tracker of the latest generation Especially in overcast conditions when light intensity is constantly changing, an extremely fast mppt controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers. In addition, the 100/30 features several other innovative technologies such as the VE.Direct communication port. Options for programming, real-time data and viewing historyModern Apple and Android smartphones, tablets, Macbooks and other devices can be connected, for example, via the integrated Bluetooth Smart Dongles and the mppt app or the gx Color Control. Please note that Bluetooth Smart Dongles and gx Color Control are separate items which are not included in the delivery of the charge controller but can be purchased optionally.Flexible charging algorithms Fully programmable charging algorithm (please refer to the software page on our website) as well as eight pre-programmed algorithms that can be selected via a rotary knob (please refer to our manual for more details) Scope of delivery: 1x Victron Energy scc110030210 SmartSolar mppt 100/30 30a 12v/24v solar charge controller1x user manual

The Victron VE.Direct Bluetooth Smart-Dongle (MPN ASS030536010) allows you to check live-status-information directly via smartphone, PC or notebook. It works hand in hand with Victron's free app 'VictronConnect'. According software for your operating system can be found in our Victron download section. Thanks to this dongle it is possible to monitor and control all your Victron VE.Direct devices wirelessly except control panels such as the Color Control GX. Some features of compatible devices can be configured via the dongle, for example the Blue MPPT charge controller's light function. Supported Victron product groups: BlueSolar MPPT charge controller series (except 150/70 and 150/85) BMV-70X battery computer series Phoenix inverter with VE.Direct-port Blue-Smart chargers Supported operating systems: iOS 11.0 or higher Android 5.0 or higher  various Windows versions Delivery scope: 1x Victron ASS030536010 VE.Direct Smart-Dongle Bluetooth

The Victron PWM-Light 12V 24V 30A (MPN SCC010030020) is a reasonable-priced PWM charge controller that was especially developed to control lighting systems. There are several possibilities to configure the switching-off/on of these DC consumers. Of course with this charge controller other things like ventilation can be controlled.Please check the manual for detailled information about the possible configurations. Important product features: Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Delivery scope:1x Victron Energy SCC010030020 PWM-Light 12/24V-30A 1x Manual

The Victron Energy SmartSolar mppt 100/50 50a 12v/24v solar charge controller (mpn scc110050210), is new version of the BlueSolar 100/50. The Smart version differs only in the from the Blue version mainly by the permanently integrated Bluetooth communication module. This allows the SmartSolar charge controller to be fully monitored and analyzed on any app-enabled device. The required Victron Connect app can be installed free of charge. key product features of the SmartSolar 100/50 50a 12v 24v mppt latest generation ultra-fast MPP tracker ensures best possible yield even in overcast conditions integrated VE.Direct data communication port high maximum efficiency of 98 for 12v and 24v systems integrated Bluetooth module 50a maximum charge current fully programmable charging algorithms that can later be manually activated and used via a switch on the case 100v maximum pv open circuit voltage 700W maximum pv power for 12v, 1400w for 24v systems integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Day/night time control and light dimming option more protection compared to the smaller models in the SmartSolar mppt seriesCompared to the 75/10, 75/15 and 100/15 model, the SmartSolar 100/30 mppt has overheating protection with shutdown function and automatic restart after reaching normal operating temperature VE.Direct data communication port VE.Direct in text mode transmits all important parameters to other devices linked to the charge controller every second, providing the possibility of communication with additional devices gx Color Control Panel from Victron. The VE.Direct connection is intended for products where a full Canbus integration (VE-Direct) would cause too high costs High-speed MPP tracker of the latest generation Especially in overcast conditions when light intensity is constantly changing, an extremely fast mppt controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers. In addition, the 100/50 features several other innovative technologies such as the VE.Direct communication port. Options for programming, real-time data and viewing historyModern Apple and Android smartphones, tablets, Macbooks and other devices can be connected, for example, via the integrated Bluetooth Smart Dongles and the mppt app or the gx Color Control. Please note that Bluetooth Smart Dongles and gx Color Control are separate items which are not included in the delivery of the charge controller but can be purchased optionally.Flexible charging algorithms Fully programmable charging algorithm (please refer to the software page on our website) as well as eight pre-programmed algorithms that can be selected via a rotary knob (please refer to our manual for more details) Scope of delivery: 1x Victron Energy scc110050210 SmartSolar mppt 100/50 50a 12v/24v solar charge controller1x user manual

The SmartSolar 150/35 mppt from Victron Energy (scc115035210) belongs to the latest generation of smart solar charge controllers, with integrated Bluetooth for data transfer and configuration via app on smartphone or tablet. It supports batteries with a voltage of 12v 24v 36v or even 48v and is therefore very versatile. The maximum charging current is 35a and uses the latest charging methods. Depending on the system voltage, the regulator can thus efficiently use 500w (12v) to 2000w (48v) to charge your batteries. In addition, this device also allows for partial shading compensation and one of the most reliable mppt trackers on the market. VE-Direct data port for programming, real time data analysis and display of history Modern Apple and Android smartphones, and tablets can be connected via VE.Direct to the system monitors gx Color Control, the Venus gx, or the mppt Control Panel, for example. High-speed mpp tracker of the latest generation Especially in overcast conditions, when light intensity is constantly changing, an extremely fast mppt controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers. In addition, the 150/35 features several other innovative technologies such as the VE.Direct communication port. extensive electronic protection Reverse battery connection protection PV reverse current lock Protection against overheating of the device Protection against short circuits Protection against reverse polarity PV connection key product features of SmartSolar 150/35 35a 12v 24v 36v 48v mppt latest generation ultra-fast mpp tracker ensures best possible yield even in overcast conditions automatic detection of mpp voltage in case of partial shading provides further yield improvement compared to "simple" mppt charge controller integrated VE.Direct data communication port for connection to additional devices like Bluetooth Smart Dongle or the gx Color Control Panel high maximum efficiency of 98 fully programmable charging algorithms which are later manually activated and toggled via a switch on the housing Rated charge current 35a, 100v maximum PV open circuit voltage 12v:500w / 24v:1000W / 36v:1500w / 48v:2000w integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option Scope of delivery1x Victron Energy scc115035210 SmartSolar mppt 150/35 12v 24v 36v 48v 35a charge controllerInstruction manual

The Victron MPPT 75/10 (MPN SCC010010050R) is part of the BlueSolar MPPT charge controller familiy and provides ultra-fast powertracking which extends your solar system's output. Next generation MPP-trackerEspecially on clouded days with changing light intensity a MPPT controler increases your system output by up to 30% compared to PWM charge controllers. Moreover the 75/10 comes with further innovative technologies. Programming, real-time data and loggingLatest Apple and Android devices (smartphones, tablets,...) can be connected via VE.Direct over Bluetooth Smart Dongles and the MPPT App or via the GX Color control.Please note that the Bluetooth Smart dongle and the GX Color Control are not included in the delivery scope but available separately. Important features: Ultra-fast MPP-tracker ensures highest possible outcome even when it is cloudy Integrated VE.Direct data port for connecting devices like the Bluetooth Smart Dongle or the GX Color Control panel Suitable for 12V and 24V systems Rated charging amperage: 10A 134W max. PV-performance at 12V and 270W at 24V 15A consumer output with auto-shutdown at imminent battery undervoltage (deep discharge protection) Reverse polarity protection Multistep adaptive charging algorithm Battery charging algorithm programmable Integrated battery life algorithm extends battery life when activated and all consumers are connected to the consumer output Day/night-time control and dimming options VE.Direct data port integratedVE.Direct transfers important parameters to all devices connected to the charge controller and allows communication to equipment such as the Bluetooth Smart Dongle or the GX Color Control. The VE.Direct data port is meant for products where a full canbus integration would produce extreme costs. Please check our Victron brand section for more information about VE.Direct. Integrated battery life algorithm extends battery lifeIf the charge controller can't manage to fully charge the battery within a day the battery status switches constantly between "partly charged" and "end of discharge". This operation mode (no regular charging) is ideal for small lead batteries, for lead-acid batteries otherwise irregular charging and discharging can cause severe damage already after several months.The battery life algorithm checks the battery's charging level and heightens the switch-off threshold from day to day. That means that connected consumers are switched off earlier until the produced energy is sufficient for a full battery charge of 100%. From this point on the threshold is modulated in a way that a full charge can be reached once a week. Delivery Scope: 1x Victron SCC010010050R BlueSolar MPPT 75/10 12V 24V 10A charge controller

The Smartsolar 75/10 from Victron Energy (mpn scc075010060r) is a mppt solar charge controller with 10a max charge current for charging 12v and 24v batteries. Unlike the Bluesolar 75/10, the Smart version has integrated Bluetooth, which eliminates the need to purchase a Bluetooth dongel. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control gx or the mppt Control. The integrated Bluetooth in the SmartSolar series is the wireless solution to setup, monitor and update the controller using Apple and Android smartphones, tablets or other devices. The most important technical features at a glance 10a max. charging current, suitable for 12v and 24v batteries nominal PV power for 12v systems: 145W nominal PV power for 24v systems: 290W 10a load output high peak efficiency of 98 freely programmable battery charging algorithm (via the free Victron Connect APP) Light dimming functions programmable (via the free Victron Connect APP) Ultra fast maximum power point tracking max. PV open circuit voltage: 75V Charging algorithm: multi-stage, adaptive integrated Bluetooth module Ultra fast maximum power point tracking Especially in overcast conditions when light intensity is constantly changing, an ultra-fast mppt controller improves power output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers. intelligent load output Deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a predefined voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is unable to charge the battery to its full capacity within a day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The Battery-Life algorithm monitors the battery's state of charge and, if necessary, raises the load disconnect threshold day by day (i.e., disconnects the load earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point, the load disconnection threshold is modulated so that charging to near 100% is achieved about once a week. Scope of delivery: 1x Victron Energy SCC075010060R Smartsolar mppt 75/10 10a 12v 24v solar charge controller 1x instruction manual

The Victron PWM-Light 12V 24V 10A (MPN SCC010010000) is a reasonable-priced PWM charge controller that was especially developed to control lighting systems. There are several possibilities to configure the switching-off/on of these DC consumers. Of course with this charge controller other things like ventilation can be controlled.Please check the manual for detailled information about the possible configurations. Important product features: Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Delivery scope:1x Victron Energy SCC010010000 PWM-Light 12/24V-10A 1x Manual

The Victron PWM-Light 12V 24V 20A (MPN SCC010020020) is a reasonable-priced PWM charge controller that was especially developed to control lighting systems. There are several possibilities to configure the switching-off/on of these DC consumers. Of course with this charge controller other things like ventilation can be controlled.Please check the manual for detailled information about the possible configurations. Important product features: Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Delivery scope:1x Victron Energy SCC010020020 PWM-Light 12/24V-20A 1x Manual

The Victron MPPT 100/30 (MPN SCC020030200) is part of the BlueSolar MPPT charge controller familiy and provides ultra-fast powertracking which extends your solar system's output. Compared to the 75/15 this controller processes a higher PV-Voltage and therefore handles a 100V DC safely. Next generation MPP-trackerEspecially on clouded days with changing light intensity a MPPT controler increases your system output by up to 30% compared to PWM charge controllers. Besides a higher charging and PV-capacity this Blue varys from the lower models. The 100/30 allows the programming and saving of different charging algorithms. Those can be adjusted simply via a switch-wheel on the device. This is the first model without a consumer output. Programming, real-time data and loggingLatest Apple and Android devices (smartphones, tablets,...) can be connected via VE.Direct over Bluetooth Smart Dongles and the MPPT App or via the GX Color control.Please note that the Bluetooth Smart dongle and the GX Color Control are not included in the delivery scope but available separately. Important features: Ultra-fast MPP-tracker ensures highest possible outcome even when it is cloudy Integrated VE.Direct data port for connecting devices like the Bluetooth Smart Dongle or the GX Color Control panel Suitable for 12V and 24V systems Rated charging amperage: 30A 200W max. PV-performance at 12V and 400W at 24V 30A consumer output with auto-shutdown at imminent battery undervoltage (deep discharge protection) Reverse polarity protection Multistep adaptive charging algorithm Battery charging algorithm programmable Integrated battery life algorithm extends battery life when activated and all consumers are connected to the consumer output Day/night-time control and dimming options VE.Direct data port integratedVE.Direct transfers important parameters to all devices connected to the charge controller and allows communication to equipment such as the Bluetooth Smart Dongle or the GX Color Control. The VE.Direct data port is meant for products where a full canbus integration would produce extreme costs. Please check our Victron brand section for more information about VE.Direct. Integrated battery life algorithm extends battery lifeIf the charge controller can't manage to fully charge the battery within a day the battery status switches constantly between "partly charged" and "end of discharge". This operation mode (no regular charging) is ideal for small lead batteries, for lead-acid batteries otherwise irregular charging and discharging can cause severe damage already after several months.The battery life algorithm checks the battery's charging level and heightens the switch-off threshold from day to day. That means that connected consumers are switched off earlier until the produced energy is sufficient for a full battery charge of 100%. From this point on the threshold is modulated in a way that a full charge can be reached once a week. Delivery Scope:1x Victron SCC020030200 BlueSolar MPPT 100/30 12V 24V 30A charge controller1x Manual

The Victron MPPT 100/50 (MPN SCC020050200) is part of the BlueSolar MPPT charge controller familiy and provides ultra-fast powertracking which extends your solar system's output. Besides a higher charging and PV-capacity this Blue varys even more from lower models. More security compared to smaller BlueSolar modelsCompared to 75/10, 75/15 and 100/15 the BlueSolar 100/50 MPPT comes with a overheat protection with auto-switch-off and auto-restart function after reaching a normal operation temperature. Moreover it is equipped with a PV-current reflow protection (the first model in this series). Next generation MPP-trackerEspecially on clouded days with changing light intensity a MPPT controler increases your system output by up to 30% compared to PWM charge controllers. Additionally the 100/50 is equipped with even more innovative technology like the VE.Direct data port.  Programming, real-time data and loggingLatest Apple and Android devices (smartphones, tablets,...) can be connected via VE.Direct over Bluetooth Smart Dongles and the MPPT App or via the GX Color control.Please note that the Bluetooth Smart dongle and the GX Color Control are not included in the delivery scope but available separately. Important features: Ultra-fast MPP-tracker ensures highest possible outcome even when it is cloudy Integrated VE.Direct data port for connecting devices like the Bluetooth Smart Dongle or the GX Color Control panel Suitable for 12V and 24V systems Rated charging amperage: 50A 700W max. PV-performance at 12V and 1400W at 24V 50A consumer output with auto-shutdown at imminent battery undervoltage (deep discharge protection) Reverse polarity protection Multistep adaptive charging algorithm Battery charging algorithm programmable Integrated battery life algorithm extends battery life when activated and all consumers are connected to the consumer output Day/night-time control and dimming options VE.Direct data port integratedVE.Direct transfers important parameters to all devices connected to the charge controller and allows communication to equipment such as the Bluetooth Smart Dongle or the GX Color Control. The VE.Direct data port is meant for products where a full canbus integration would produce extreme costs. Please check our Victron brand section for more information about VE.Direct. Integrated battery life algorithm extends battery lifeIf the charge controller can't manage to fully charge the battery within a day the battery status switches constantly between "partly charged" and "end of discharge". This operation mode (no regular charging) is ideal for small lead batteries, for lead-acid batteries otherwise irregular charging and discharging can cause severe damage already after several months.The battery life algorithm checks the battery's charging level and heightens the switch-off threshold from day to day. That means that connected consumers are switched off earlier until the produced energy is sufficient for a full battery charge of 100%. From this point on the threshold is modulated in a way that a full charge can be reached once a week. Delivery Scope:1x Victron SCC020050200 BlueSolar MPPT 100/50 12V 24V 50A charge controller1x Manual

This 1.8m Victron VE.Direct Cable (ASS030530209) is used to connect devices for communication via the VE.Direct-port, for example BlueSolar charge controllers and MPPT Control remote panel. Possible connections:Victron BlueSolar MPPT charge controller to Color Control GX PanelVictron BlueSolar MPPT charge controller to MPPT Control remote unit BMV70xxx-series to Color Control GX PanelBMV60xxx to Color Control GX Panel VE.Direct cables are not included in these device's delivery scopes and available in lengths of 0.3 to 10m. Delivery scope:1x Victron ASS030530218 1.8m VE.Direct Cable

Though a sound beginner's device the Victron BlueSolar PWM-PRO 10A (MPN SCC010010010) provides several professional functions. It can by applied in 12V and 24V systems and is therefore widely usable. Victron's BlueSolar-series provides more user comfort and possible configurations compared to the PWM-Light-series. Optionally a remote control display can be connected for an even more comfortable operation. All control parameters can be programmed freely via remote panel or USB link + PC-software Via the optional remote panel all relevant settings like charging voltage can be programmed freely. A feature normally found only in high-class devices. Specific charging and discharging voltage depending on the battery type as well as the switch-off/on tresholds of the consumer output can be adjusted. The remote panel is optional equipment and not included in the charge controller's delivery scope. You find this item in our shop under article number 8-67-008490. A more economical alternative to the remote panel is the Victron USB link cable. Additionally you receive the Victron Pc software which allows full programming of your charge controller as well as the generation of comprehensive performance statistics. This cable is available in our shop under article number 1-67-008500. Important features: 10A max. charging amperage, 10A max. solar performance optional remote panel available parameters like charging voltage freely programmable via remote panel suitable for AGM, gel and lead-acid batteries suitable for 12V and 24V battery voltage fully programmable lighting control full battery charging thanks to 3-step charging process consumer output with overload and short-circuit protection as well as switch-off function to avoid battery deep discharge optional temperature sensor available reverse polarity protection for solar and battery input Delivery scope:1x Victron MPN SCC010010010 BlueSolar PWM-PRO 10A 12V 24V1x Manual

The Victron PWM-Light 48V 20A (MPN SCC040020020) is a reasonable-priced PWM charge controller that was especially developed to control lighting systems. There are several possibilities to configure the switching-off/on of these DC consumers. Of course with this charge controller other things like ventilation can be controlled.Please check the manual for detailled information about the possible configurations. Important product features: Load output with low battery voltage disconnect function. Lighting control function, one timer only. Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Delivery scope:1x Victron Energy SCC040020020 PWM-Light 48V-20A 1x Manual

The Smartsolar 100/15 from Victron Energy (mpn scc110015060r) is a mppt solar charge controller with 15a max charge current for charging 12v and 24v batteries. Unlike the Bluesolar 100/15, the Smart version has integrated Bluetooth, which eliminates the need to purchase a Bluetooth dongel. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control gx or the mppt Control.The integrated Bluetooth in the SmartSolar series is the wireless solution to setup, monitor and update the controller using Apple and Android smartphones, tablets or other devices The most important technical features at a glance 15a max charge current, suitable for 12v and 24v batteries nominal PV power for 12v systems: 220w nominal PV power for 24v systems: 440w 15a load output high peak efficiency of 98 freely programmable battery charging algorithm (via free Victron Connect app) Light dimming functions programmable (via free Victron Connect app) Ultra fast maximum power point tracking max. PV open circuit voltage: 100v Charging algorithm: multi-level, adaptive integrated Bluetooth modu Ultrafast Maximum Power Point TrackingEspecially in overcast conditions when light intensity is constantly changing, an ultra-fast mppt controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers intelligent load outputDeep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an algorithm for intelligent battery management can be selected: see BatteryLife.The load output is short circuit protected Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months The Battery-Life algorithm monitors the battery's state of charge and, if necessary, raises the load disconnect threshold day by day (i.e., disconnects the load earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point, the load disconnection threshold is modulated so that charging to near 100% is achieved approximately once a week Scope of delivery:1x Victron Energy SCC110015060R Smartsolar mppt 100/15 15a 12v 24v solar charge controller1x instruction manual

The Smartsolar mppt 250/100-tr from Victron Energy (mpn scc125110210), belongs to the latest generation of smart solar controllers from the Dutch premium manufacturer. Ultra-fast power tracking and automatic power point detection in case of partial shading are just 2 of the many highlights of this new class of devices. In addition, this model is capable of parallel operation with other controllers of the same type Compared to the Smartsolar 150/..... Series, the 250/.... Series can handle a maximum PV input voltage of 250v. This is also one of the reasons why the 250 solar controller family has been able to increase efficiency by another 1 percent to a total of 99%, defining new standards in the industry. Among all solar charge controllers we know, this value is currently the best. Compared to the BlueSolar family, the Bluetooth module is already integrated in the controller of the 250 Smartsolar series, which makes the smart dongle superfluous for this device, if you want to analyze and configure the controller via smartphone or tablet Also new is the optionally available lcd display, which can simply be plugged onto the SmartSolar 150/85-tr as required. The display then provides all the important information about the controller smart configuration and analysis via Victron Connect App Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the permanently integrated Bluetooth module and the free Victron Connect app. The app can then be used to configure many important functions of the SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points (mppts) on the current-voltage curve. Conventional mppts tend to settle on a local mpp. However, this may not be the optimal mpp. The SmartSolar controller's innovative algorithm will always maximize energy output by adjusting to the optimal mpp key product features of the SmartSolar 250/100-Tr 100a 12v 24v 36v 48v mppt latest generation ultra-fast mpp tracker ensures best possible yield even in overcast conditions automatic detection of mpp voltage in case of partial shading provides further yield improvement compared to "simple" mppt charge controller with optional lcd display integrated bluetooth module for app based analysis and configuration of the controller (via free Victron app on compatible devices) optional lcd display available max. PV power: 12v 1450w / 24v 2900w / 48v 5800W max rated charge current 100a, 150v max PV open circuit voltage max. PV input current: 250 volts integrated VE.Direct data communication port for connection To communicate with auxiliary devices the gx Color Control Panel or a Smart bmv battery monitor groundbreaking 99% efficiency Parallel operation with other 250/85 controllers possible Adjustable constant charge voltage Adjustable float charge voltage Suitable for all agm, gel, lead-acid calcium-calcium and lithium batteries fully programmable charging algorithms which are later manually activated and toggled via a switch on the case integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm remote on/off switching via 2-pin plug possible Protection class ip 43 for the electronic components and protection class ip 22 for the connection area of the controller integrated temperature sensor balances maintenance and constant charging voltage according to temperature Day/night time control and light dimming option Latest generation high speed mpp tracker Especially in overcast conditions when light intensity is constantly changing, an extremely fast mppt controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower mppt controllers optional lcd display available for retrofitting For those who prefer to operate and configure the Smartsolar mppt 250/100-tr directly, the Smartsolar Control scc900600010 display can be retrofitted. The installation effort is only limited to plugging the display onto the SmartSolar. The display allows easy configuration of the controller via key input, and also provides all important performance data at a glance extensive electronic protection Reverse battery connection protection PV reverse current lockout Protection against overheating of the device Protection against short circuits Protection against reverse polarity PV connection the VE.Direct data communication port VE.Direct in text mode transmits all important parameters to other devices coupled to the charge controller every second, providing the possibility of communication with auxiliary devices system panel gx Color Control. The VE.Direct connection is intended for products where a full Canbus integration (VE-Direct) would be too costly. More information about VE.Direct can be found in our Victron Energy brand store optionally also available as version with MC4 connectors The devices of the classes 250/60-Tr to 250/100-Tr are also available as a version with MC4 connections on the solar side of the charge controller instead of the screw terminals Scope of delivery 1x Victron scc125110210 SmartSolar mppt 250/100-tr 12v 24v 36v 48v 85a charge controller 1x instruction manual

This 10m Victron VE.Direct Cable (ASS030530310) is used to connect devices for communication via the VE.Direct-port, for example BlueSolar charge controllers and MPPT Control remote panel. Possible connections:Victron BlueSolar MPPT charge controller to Color Control GX PanelVictron BlueSolar MPPT charge controller to MPPT Control remote unit BMV70xxx-series to Color Control GX PanelBMV60xxx to Color Control GX Panel VE.Direct cables are not included in these device's delivery scopes and available in lengths of 0.3 to 10m. Delivery scope:1x Victron ASS030530310 10m VE.Direct Cable

The Smartsolar Control Display from Victron (mpn scc900600010) easily attaches to the solar charge controller series of the same name and allows you to easily read the most important parameters of your solar system.Compatible with the Smartsolar 150/45 and upwards to the 250/100. Smaller Smartsolar controllers have no Slot for the display. allows easy configuration of the controller compatible with alem SmartSolar charge controllers all important performance data at a glance Scope of delivery:1x Smartsolar Control scc900600010 Display for SmartSolar controller 150/45 - 250/100

The Smartsolar mppt 150/70-tr from victron Energy (mpn scc115070210), belongs to the latest generation of smart solar controllers from the Dutch premium manufacturer and processes a whopping 70a of solar power and can work flexibly with 12/24/36/48 v batteries. Ultra-fast power tracking and automatic power point detection in case of partial shading are just 2 of the many highlights of this new class of devices. The SmartSolar 150/70-tr is also available as a version with MC4 connections on the solar side of the charge controller instead of screw terminals. In addition, this model is capable of parallel operation with other controllers of the same type Compared to the BlueSolar series, the Bluetooth module is already integrated in the controller of the Smartsolar family, which makes the smart dongle superfluous for this device. Also new is the optionally available lcd display, which can be simply plugged onto the SmartSolar 150/70-tr as required. The display then provides all the important information about the controller smart data communication via vE.Direct and lightning-fast Bluetooth Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the permanently integrated Bluetooth module and the free victron Connect app. The app can then be used to configure many important functions of the mppt 150/70-tr SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points (mppts) on the current-voltage curve. Conventional mppts tend to settle on a local mpp. However, this may not be the optimal mpp. The SmartSolar 150/70-tr's innovative algorithm will always maximize energy output by adjusting to the optimal mpp key product features of the SmartSolar 150/70-tr 70a 12v 24v 36v 48v mppt latest generation ultra-fast mpp tracker ensures best possible yield even in overcast conditions Rated charge current 70a, 150v maximum pv open circuit voltage maximum pv power: 12 v 1000 w / 24 v 2000 w / 48 v 4000 w victron Energy part number (mpn): scc115070210 automatic detection of mpp voltage in case of partial shading provides further yield improvement compared to "simple" mppt charge controller with optional lcd display permanently integrated Bluetooth module for app-supported analysis and configuration of the controller (via free victron app on compatible devices) optional lcd display available integrated vE.Direct data communication port for connection to the gx Color Control Panel or a Smart BMv battery monitor for communication with additional devices high maximum efficiency of 98 Parallel operation with other 150/70-tr controllers possible adjustable constant charging voltage adjustable float charge voltage suitable for all agm, gel, lead-acid calcium-calcium and lithium batteries fully programmable charging algorithms which are later activated and switched manually via a switch on the case integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm remote switching on and off possible via 2-pin plug Protection class ip 43 for the electronic components and protection class ip 22 for the connection area of the controller integrated temperature sensor balances maintenance and constant charging voltage according to temperature Day/night time control and light dimming option Latest generation high-speed mpp tracker Especially in overcast conditions, when light intensity is constantly changing, an extremely fast mppt controller improves energy yield by up to 30% compared to PwM charge controllers and by up to 10% compared to slower mppt controllers extensive electronic protection Protection against reverse battery connection Pv reverse current lock Protection against overheating of the device Protection against short circuits Protection against reverse polarity Pv connection the vE.Direct data communication port vE.Direct in text- mode transmits all important parameters to other devices coupled to the charge controller every second, offering the possibility of communication with additional devices system panel gx Color Control. The vE.Direct connection is intended for products where full Canbus integration (vE-Direct) would be too costly. More information about vE.Direct can be found in our victron Energy brand store Scope of delivery 1x victron scc115070210 SmartSolar mppt 150/70-tr 12v 24v 36v 48v 70a charge controller Instruction manual

The MPPT 150/45tr (MPN SCC010045200) is part of the BlueSolar MPPT charge controller familiy. Ultra-fast powertracking and automatic MPP-voltage adjustment extend your solar system's output. Models from 150/45tr to 150/100tr are also available with MC4-connections instead of screw clamps (solar input). Additionally this model supports concurrent operation with other controllers of the same type. Programming, real-time data and loggingLatest Apple and Android devices (smartphones, tablets,...) can be connected via VE.Direct over Bluetooth Smart Dongles and the MPPT App or via the GX Color control.Please note that the Bluetooth Smart dongle and the GX Color Control are not included in the delivery scope but available separately. Next generation MPP-trackerIn case of partial module shading there can be more than one point of maximum performance on the voltage curve. Common MPPTs tend to switch to a local MPP even if it not the ideal one. The innovative algorithm used in BlueSolar devices maximizes the energery outcome by always adjusting to the optimal MPP.  Important features: Ultra-fast MPP-tracker ensures highest possible outcome even when it is cloudy Auto-detection of partly shading and adjustment to the ideal MPP - more outcome compared to "simple" MPPT charge controllers Integrated VE.Direct data port for connecting devices like the Bluetooth Smart Dongle or the GX Color Control panel High effectivity of 98% Concurrent operation with other 150/45 controllers possible Constant charging voltage adjustable Trickle charge voltage adjustable Supported battery types: AGM, gel, lead-acid, calcium-calcium and lithium batteries tr-Version: solar modules connectable via screw clamps (max. 35mm² Fully programmable charging algorithms that can be changed via a switch on the device Rated charging amperage: 45A, 150V max. PV no-load voltage 12V: 650W / 24V: 1300W / 48V: 2600W Integrated protection from reverse battery polarity Multistep adaptive charging algorithm Integrated temperature sensor adjusts Charging processes according to battery temperature Day/night-time control and dimming options Extensive protection functions from: reverse battery polarity PV current reflow overheating short-cicuits reverse PV-connection polarity VE.Direct data port integratedVE.Direct transfers important parameters to all devices connected to the charge controller and allows communication to equipment such as the Bluetooth Smart Dongle or the GX Color Control. The VE.Direct data port is meant for products where a full canbus integration would produce extreme costs. Please check our Victron brand section for more information about VE.Direct. Delivery Scope:1x Victron SCC010045200 BlueSolar MPPT 150/45tr 12V 24V 36V 48V 45A charge controller1x Manual

The Smartsolar mppt 250/70-tr from victron Energy (mpn scc125070210), is part of the latest generation of smart solar controllers from the premium Dutch manufacturer. The controller handles a whopping 70a of solar power and can flexibly work with 12/24/36/48 v batteries, with a maximum Pv input voltage of 250v dc. Ultra fast power tracking and automatic power point detection in case of partial shading are only 2 of the many highlights of this new class of devices. In addition, this model is capable of parallel operation with other controllers of the same type. Compared to the Smartsolar 150/..... Series, the 250/.... Series can handle a maximum Pv input voltage of 250v. This is also one of the reasons why the 250 solar controller family has been able to increase the efficiency by another 1 percent to a total of 99%, defining new standards in the industry. Among all solar charge controllers we know, this value is currently the best. In comparison to the BlueSolar family, the Bluetooth module is already integrated in the controller of the 250 Smartsolar series, which makes the smart dongle superfluous for this device, if you want to analyze and configure the controller via smartphone or tablet. Also new is the optionally available lcd display, which can be simply plugged onto the SmartSolar 250/70-tr as required. The display then provides all the important information about the controller smart configuration and analysis via victron Connect App Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the permanently integrated Bluetooth module and the free victron Connect app. The app can then be used to configure many important functions of the SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points (mppts) on the current-voltage curve. Conventional mppts tend to settle on a local mpp. However, this may not be the optimal mpp. The SmartSolar controller's innovative algorithm will always maximize energy output by adjusting to the optimal mpp key product features of the SmartSolar 250/70-tr 70a 12v 24v 48v mppt victron Energy part number: scc125070210 max pv power: 12 v 1000 w / 24 v 2000 w / 48 v 4000 w max rated charge current 70a, 250v max pv open circuit voltage latest generation ultra-fast mpp tracker ensures best possible yield even in overcast conditions automatic detection of mpp voltage in case of partial shading provides further yield improvement compared to "simple" mppt charge controller with optional lcd display permanently integrated Bluetooth module for app-supported analysis and configuration of the controller (via free victron app on compatible devices) optional lcd display available integrated vE.Direct data communication port to connect for communication with additional devices the gx Color Control Panel or a Smart BMv battery monitor groundbreaking 99% efficiency Parallel operation with other 250/85 controllers possible adjustable constant charging voltage adjustable float charge voltage suitable for all agm, gel, lead-acid calcium-calcium and lithium batteries fully programmable charging algorithms which are later activated and switched manually via a switch on the case integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm remote switching on and off possible via 2-pin plug Protection class ip 43 for the electronic components and protection class ip 22 for the connection area of the controller integrated temperature sensor balances maintenance and constant charging voltage according to temperature Day/night time control and light dimming options Latest generation high-speed mpp tracker Especially in overcast conditions, when light intensity is constantly changing, an extremely fast mppt controller improves energy yield by up to 30% compared to PwM charge controllers and by up to 10% compared to slower mppt controllers optional lcd display available for retrofitting for those who prefer to operate and configure the Smartsolar mppt 250/70-tr directly, the Smartsolar Control scc900600010 display is available for retrofitting. The display allows easy configuration of the controller via key input, and also provides all important performance data at a glance extensive electronic protection Protection against reverse battery connection Pv reverse current lock Protection against overheating of the device Protection against short circuits Protection against reverse polarity Pv connection the vE.Direct data communication port vE.Direct in text- mode transmits all important parameters to other devices coupled to the charge controller every second, offering the possibility of communication with additional devices such as the gx Color Control system panel. The vE.Direct connection is intended for products where full Canbus integration (vE-Direct) would be too costly. More information about vE.Direct can be found in our victron Energy brand store optionally also available as version with MC4 connectors The 250/70-tr is also available as a version with MC4 connectors on the solar side of the charge controller instead of screw terminals Scope of delivery 1x victron scc125070210 SmartSolar mppt 250/70-tr 12v 24v 48v 70a charge controller 1x instruction manual