Powerful All-in-One Complete Solar System The 24v Autark XXL-Master is one of the larger complete systems of the Autark family and delivers an average daily yield of 4800 watt hours between March and October. The generated power is stored in two series connected 260Ah agm batteries - the high quality charge controller with integrated display gives you information about the state of charge of the battery while your 230v consumers can be operated at the sine wave voltage converter. Of course, the whole thing is delivered including a professional connection cable kit - plug it together and get started. The system is suitable for a wide range of applications - from 24v lighting, charging laptop, cell phone and camera batteries and other small consumers, to 230v household appliances with a maximum continuous power of 3000w (15min) Features of the 24v Autarkic XXL-Master Average daily output between March and October: approx. 4.8KW Plug & Play ready to connect system - plug together and go Allows operation of 24v and 230v loads, as well as 5v usb consumers usb charging possibility directly at the charge controller (max. 2,4A) Easy to read lcd display informs about all operating parameters Flexible mounting possibility thanks to 8m connection cable from module to controller Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage shutdown, short-circuit protection, reverse polarity protection, etc. rs485 communication port on the voltage transformer offers extensive configuration possibilities via pc (interface cable rs485 to usb not included) Charge controller enables temperature compensated charging - temperature sensor included in scope of delivery Configurable 12/24v load output at the charge controller for loads up to max. 45a - suitable e.g. for lighting control Application areas This complete system can be used in many ways. Whether as a stationary system on the mountain hut or in the allotment garden - the permanent operation of small coolers and refrigerators, as well as the charging of cell phones and laptops succeeds easily with this system. The installation on the motor home is also conceivable - we also have the corresponding brackets and adhesive sets for the attachment. Extensive connection options 230v ac 50hz 2000w (15min - 3000w / peak - 6000w) sine wave voltage converter 24v consumer output with 45a power directly on the charge controller 2 x usb charge port on the charge controller with max. 2.4a (total) 1 x usb charge port at the voltage converter with max. 1a power Parts list - what's inside 6 x 200w monocrystalline solar panel of Offgridtec1500 x 680 x 35mm 1 x 45a pwm charge controller with clear lcd display and usb charging possibility - the unit also has a 45a load output and is easy to operate - all important parameters can be read on the display 2 x 260Ah agm battery with m8 screw terminal Dimensions: 520 x 268 x 220mm(+29mm terminal) - the batteries are absolutely maintenance free and leak proof and last up to 10 years depending on usage 1 x 3000w 24v to 230v sine wave voltage converter- the rated power of 3000w can be output by the device for 15 minutes - beyond that the inverter can handle short time starting currents up to 6000w 1 x 10m 10mm² professional connection cable solar module to charge controller with original Stäubli mc4 connectors and high quality Lapp Ölflex 1x10mm² solar cable (ready to connect cable harness to connect the 6 modules) 1 x 1.5m 10mm² professional battery connection cablewith MIDI fuse holder, 50a MIDI fuse and m8 ring terminals for the connection between charge controller and battery 1 x Temperature sensor with 3m length for connection of the controller to the battery 1 x 1m 35mm² connection cable from inverter to battery 1 x Fuse holder + 125A Mega fuse+ short connection cable for installation between voltage transformer and battery positive pole for protection against short circuit 1 x Battery jumper for connection from positive pole battery 1 to negative pole battery 2 (serial connection to 24v) Note and accessories recommendation If you plan to leave consumers permanently switched on at the voltage converter, we recommend the use of an additional deep discharge protection. The voltage transformer switches off the connected consumer when undervoltage is reached - but not itself. In case of longer absence (e.g. over night) the battery can be deeply discharged by the self-consumption of the voltage converter and thus be irreparably damaged. In this case we recommend the use of a Victron Battery Protect battery protector. For the included voltage transformer you need the 220a version (bp-220). For the installation of the device between the voltage transformer and the battery you still need a 1 short connection cable. If available, you can alternatively connect the remote contact of the psi-pro to the load output of your charge controller. Then the psi-pro is switched on or off, depending on the setting of the load output. In 24v systems, over time, the interconnected batteries may not charge evenly. This means that a battery is never fully charged, which can have a negative effect on durability in the long run. To ensure that the charge of the batteries is always balanced, it is recommended to use a Battery balancer. Roof mount for the solar module Since there are different requirements for the mounting of a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mount as standard. This can of course be purchased additionally - find suitable suggestions here: Solar module holder for flat roof or wall mounting (6x needed) Mounting kit for pitched roof mounting on roof tiles, Frankfurter Pfanne etc. (2x needed) Fastening kit for pitched roof installation on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure (2x needed) Fixing kit for pitched roof mounting on plain tiles (2x needed) Scope of delivery: 1x 24v Solaranlage Autark XXL-Master with 6x 200w solar panel, 45a pwm charge controller with lcd display and usb ports, 3000w sine wave voltage converter, 2 x 260Ah agm rechargeable battery, user manuals

Powerful all-in-one solar complete system The Autark S-Master is the smallest complete system of the Autark family and delivers an average daily yield of 520 watt hours between March and October. The generated power is stored in the cycle resistant 101ah agm battery - the high quality charge controller with integrated display gives you information about the charge status of the battery while your 230v consumers can be operated up to the sine wave voltage converter. Of course, the whole thing is delivered including a professional connection cable kit - plug it together and get started. The system is suitable for a whole range of applications - from 12v lighting, charging laptop, cell phone and camera batteries and other small consumers, to 230v household appliances with a continuous output of 3000w Features of the Autark S-Master If necessary, module-side expandable by 1 x 130w with little installation effort Average daily yield between March and October: approx. 520Wh (approx. 45Ah) Plug & Play System ready for connection - plug together and go Enables operation of 12v and 230v consumers, as well as 5v usb consumers usb charging possibility directly at the charge controller (5vDC/1) Easy to read lcd display informs about all operating parameters Flexible installation possibility thanks to 8m connection cable from module to controller Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage cut-off, short-circuit protection, reverse polarity, etc. Charge controller enables temperature-compensated charging - temperature sensor included Configurable 24v load output on the charge controller Areas of application This complete system can be used in a variety of ways. Whether as a stationary system on the mountain hut or in the allotment garden - the permanent operation of small coolers and charging of cell phone and laptop succeeds easily with this system. Also the installation on the motorhome is conceivable - we also carry appropriate brackets and adhesive sets for mounting on such. Extensive connection options 12v consumer output with 20a power directly on the charge controller 2 x usb charging port on the charge controller with max. 2.4a (total) 1 x usb charging port on the voltage converter with max. 1a power Parts list - what's inside 1 x 130w monocrystalline solar panel from Offgridtec 1205 x 670 x 35mm 1 x 20a pwm charge controller with clear lcd display and usb charging capability - the unit also has a 20a load output and is easy to use - all important parameters can be read on the display 1 x 101ah agm battery with m8 screw terminal Dimensions: 330 x 172 x 215mm(+5mm terminal) - the battery is absolutely maintenance free and leak proof and lasts up to 10 years depending on usage 1 x 3000w 24v to 230v sine wave voltage converter incl. 1 x 8m 6mm² professional connection cable solar module to charge controller with original Stäubli mc4 connectors and high quality Lapp Ölflex 2x6mm² solar cable 1 x 1.5m professional battery connection cable with 25a flat fuse and m8 ring terminals for the connection between charge controller and battery 1 x temperature sensor with 3m length for the connection of the controller to the battery fuse holder + 80a mega fuse for installation between voltage converter and battery positive pole to protect against short circuit Note and accessories Recommendation If you plan to leave consumers permanently switched on at the voltage converter, we recommend the use of an additional deep discharge protection. The voltage transformer switches off the connected consumer when undervoltage is reached - but not itself. In case of longer absence (e.g. over night) the battery can be deeply discharged by the self-consumption of the voltage converter and thus be irreparably damaged. In this case, we provide for the use of a Victron Battery Protect. For the included voltage transformer the 65a version is sufficient. For the installation of the device between voltage converter and battery a short connection cable is still needed. Roof mount for the solar module Since there are different requirements for the mount for a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mount as standard. This can of course be purchased additionally - find suitable suggestions here: Solar module holder for flat roof or wall mounting Mounting kit for pitched roof mounting on roof tiles (Frankfurter Pfanne and similar.) Mounting kit for pitched roof mounting on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure Mounting kit for pitched roof mounting on beavertail tiles Scope of delivery: 1x Solaranlage Autark S-Master with 130w solar module, 20a pwm charge controller with lcd display and usb ports, 3000w sine wave voltage converter, 101ah agm battery, operating instructions

Powerful all-in-one complete solar system The Autark XL-Master is one of the larger complete systems of the Autark family and delivers an average daily yield of 1200 watt hours between March and October. The generated electricity is stored in the cycle-proof 154Ah AGM battery - the high-quality charge controller with integrated display provides you with information about the battery's state of charge while your 230V consumers can be operated at the sine voltage converter. Of course, the whole system is supplied with a professional connection cable kit - plug it together and get started. The system is suitable for a whole range of applications - from 12V lighting, charging laptop, mobile phone and camera batteries and other small consumers, to 230V household appliances with a maximum continuous power of 1500W (15min). Features of the Autark XL-Master If required, can be extended by 2 x 150W on the module side with little installation effort. Average daily yield between March and October: approx. 1200Wh (approx. 100Ah) Plug & Play ready-to-connect system - plug together and go Allows operation of 12V and 230V loads, as well as 5V USB consumers USB charging possibility directly at the charge controller (max. 2.4A) Easy-to-read LCD display provides information on all operating parameters Flexible installation thanks to 8m connection cable from module to controller Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage cut-off, short-circuit protection, reverse polarity protection, etc. RS485 communication port on the voltage transformer offers extensive configuration options via PC (interface cable RS485 to USB included) Charge controller enables temperature-compensated charging - temperature sensor included in delivery Configurable 12V load output on the charge controller for loads up to max. 45A - suitable e.g. for lighting control Areas of application This complete system can be used in a variety of ways. Whether as a stationary system on a mountain hut or in an allotment garden - the permanent operation of small coolers and refrigerators, as well as the charging of mobile phones and laptops, is easy with this system. Installation on a motor home is also conceivable - we also have the corresponding brackets and adhesive sets for mounting. Extensive connection options 230V AC 50HZ 1500W (15min - 1500W / permanent - 1200W) Schuko socket on the sine wave voltage converter 12V consumer output with 45A power directly at the charge controller 2 x USB charging port on the charge controller with max. 2.4A (total) 1 x USB charging port on the voltage converter with max. 1A output Parts list - what's inside 2 x 150W monocrystalline solar module from Offgridtec 1140 x 680 x 35mm 1 x 1 pair of solar connectors compatible junction sockets for connecting the two solar modules in parallel 1 x 45A PWM charge controller with clear LCD display and USB charging option - the unit also has a 45A load output and is easy to operate - all important parameters can be read on the display 1 x 154Ah AGM battery with M8 screw terminal terminal Dimensions: 485 x 172 x 240mm (+5mm terminal) - the battery is absolutely maintenance-free and leak-proof and lasts up to 10 years depending on use 1 x 1500W 12V to 230V sine wave voltage converter with a shock-proof socket incl. connection cable - the rated power of 1500W can be output by the unit for 15 minutes - in addition, the inverter has an output of 1200W and can handle short-time starting currents of up to 2400W 1 x 8m 6mm² professional connection cable solar module to charge controller with solar connector plug 1 x 1.5m 10mm² battery connection cable with MIDI fuse holder and M8 ring terminals for connection between charge controller and battery 1 x Temperature sensor with 3m length for connecting the controller to the battery 1 x Battery connection cable 25mm² 40cm Ozone, UV and temperature resistant 1 x Fuse holder 1 x 250A Mega fuse For installation between voltage transformer and battery positive pole for protection against short circuit 1 x 50A Midi Fusse Note and accessories Recommendation If you plan to leave consumers permanently switched on at the voltage transformer, we recommend the use of an additional deep discharge protection. The voltage transformer switches off the connected load when undervoltage is reached - but not itself. During longer absences (e.g. overnight), the battery can be deeply discharged by the voltage converter's own consumption and thus irreparably damaged. In this case, we envisage the use of aVictron Battery Protect. For the included voltage transformer you need the 220A version. For the installation of the unit between the voltage transformer and the battery,  short connection cable is also required. Roof bracket for the solar module As there are different requirements for the mounting of a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mounting as standard. This can, of course, be purchased additionally - find suitable suggestions here: Solar module holder for flat roof or wall mounting Solarmodulhalter für Flachdach- oder Wandmontage Fastening kit for pitched roof installation on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure Fixing kit for pitched roof mounting on beavertail tiles Scope of delivery: 1x Solar system Autark XL-Master with 2x150W solar module, 45A PWM charge controller with LCD display and USB ports, 1500W sine wave voltage converter, 154Ah AGM battery, operating instructions

Powerful All-in-One Complete Solar System The Autark XXL-Master is one of the larger complete systems of the Autark family and delivers an average daily yield of 2400 watt hours between March and October. The generated power is stored in the cycle-proof 234Ah agm battery - the high quality charge controller with integrated display gives you information about the battery charge status while your 230v consumers can be operated at the sine wave voltage converter. Of course, the whole thing is delivered including a professional connection cable kit - plug it together and get started. The system is suitable for a wide range of applications - from 12v lighting, charging laptop, cell phone and camera batteries and other small consumers, to 230v household appliances with a maximum continuous power of 2000w Features of the Autark XL-Master Average daily yield between March and October: approx. 2400Wh (approx. 200Ah) Plug & Play ready-to-connect system - plug it together and go Allows operation of 12v and 230v loads, as well as 5v usb consumers usb charging possibility directly at the charge controller (max. 2,4A) Easy to read lcd display informs about all operating parameters Flexible mounting possibility thanks to 10m connection cable from module to controller Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage shutdown, short-circuit protection, reverse polarity protection, etc. rs485 communication port on the voltage transformer offers extensive configuration possibilities via pc (interface cable rs485 to usb included) Charge controller enables temperature compensated charging - temperature sensor included in delivery Configurable 12v load output at the charge controller for loads up to max. 45a - suitable e.g. for lighting control Application areas This complete system can be used in many different ways. Whether as a stationary system on the mountain hut or in the allotment garden - the permanent operation of small coolers and refrigerators, as well as the charging of cell phones and laptops succeeds easily with this system. Installation on the motor home is also conceivable - we also carry the corresponding brackets and adhesive sets for mounting. Extensive connection options 230v ac 50hz 2000w (permanent 2000w - peak power 4000w) Schuko socket at the sine wave voltage converter 12v consumer output with 45a power directly at the charge controller 2 x usb charging port at the charge controller with max. 2.4a (total) 1 x usb charging port at the voltage converter with max. 1a power Parts list - what's inside 4 x 150W Monocrystalline Solar Panel from Offgridtec 1140 x 680 x 35mm 1 x ready made cable harness with Junction boxes and Connecting cablesfor connection of all modules 1 x 45a pwm charge controller with clear lcd display and usb charging possibility - the device also has a 45a load output and is easy to operate - all important parameters can be read on the display 1 x 234Ah agm battery with m8 screw terminal Dimensions: 521 x 269 x 203mm (+5mm terminal) - the battery is absolutely maintenance free and leak proof and lasts up to 10 years depending on use 1 x 2000w 12v to 230v sine wave voltage converter with an earthed socket - it outputs a constant continuous power of 2000w - and can handle short time starting currents up to 4000w 1 x 10m 10mm² professional connection cable solar module to charge controller with original Stäubli mc4 connectors and high quality Lapp Ölflex 2x10mm² solar cable 1 x 1.5m 10mm² professional battery connection cable with MIDI fuse holder and 50a MIDI fuse and m8 ring terminals for the connection between charge controller and battery 1 x Temperature sensor with 3m length for connection of the controller to the battery 1 x 1m 35mm² connection cable from inverter to battery (fuse holder included with the voltage converter) 1 xHolder for Mega fuse +250a Mega fuse for installation between voltage transformer and battery positive pole for protection against short circuit Note and accessories recommendation If you plan to leave consumers permanently switched on at the voltage transformer, we recommend the use of an additional deep discharge protection. The voltage transformer switches off the connected consumer when undervoltage is reached - but not itself. In case of longer absence (e.g. over night) the battery can be deeply discharged by the self-consumption of the voltage converter and thus be irreparably damaged. In this case we recommend the use of a Victron Battery Protect battery protector. For the included voltage transformer you need the 220a version. For the installation of the device between the voltage transformer and the battery you will still need a short connection cable is needed. Roof mount for the solar module Since there are different requirements for the mounting of a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mount as standard. This can of course be purchased additionally - find suitable suggestions here: Solar module holder for flat roof or wall mounting Mounting kit for pitched roof mounting on roof tiles (Frankfurter Pfanne etc.) Mounting kit for pitched roof mounting on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure Fastening kit for pitched roof installation on Bieberschwanz tiles Scope of delivery: 1x Solaranlage Autark XXL-Master with 4x150W solar panel, 45a pwm charge controller with lcd display and usb ports, 2000w sine wave voltage transformer, 234Ah agm battery, user manuals

The Autark M-Master is the medium sized complete system of the Autark family and delivers an average daily yield of 800 watt hours between March and October. The generated power is stored in the cycle-proof 122Ah agm battery - the high-quality charge controller with integrated display gives you information about the charge status of the battery while your 230v consumers can be operated at the sine wave voltage converter. Of course, the whole thing is delivered including a professional connection cable kit - plug it together and get started. The system is suitable for a wide range of applications - from 12v lighting, charging laptop, cell phone and camera batteries and other small consumers, to 230v household appliances with a maximum continuous power of 1000w (15min) Features of the Autark M-Master If required, module side expandable by 2 x 100w with low installation effort Average daily yield between March and October: approx. 800wh (approx. 66Ah) Plug & Play ready-to-connect system - plug together and go Allows operation of 12v and 230v loads, as well as 5v usb consumers usb charging possibility directly at the charge controller (max. 2,4A) Easy to read lcd display informs about all operating parameters Flexible mounting possibility thanks to 8m connection cable from module to controller Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage shutdown, short-circuit protection, reverse polarity protection, etc. rs485 communication port on the voltage transformer offers extensive configuration possibilities via pc (interface cable rs485 to usb included) Charge controller enables temperature compensated charging - temperature sensor included in delivery Configurable 12v load output at the charge controller for loads up to max. 30a - suitable e.g. for lighting control Application areas This complete system can be used in many ways. Whether as a stationary system on the mountain hut or in the allotment garden - the permanent operation of small coolers and refrigerators, as well as the charging of cell phones and laptops succeeds easily with this system. The installation on the motor home is also conceivable - we also have the corresponding brackets and adhesive sets for the attachment. Extensive connection options 230v ac 50hz 1000w (15min - 1000w / permanent - 800w / short time (starting currents) - 1600w) Schuko socket on the sine wave voltage converter 12v consumer output with 30a power directly at the charge controller 2 x usb charging port at the charge controller with max. 2.4a (total) 1 x usb charging port at the voltage converter with max. 1a power Parts list - what's inside 2 x 100w monocrystalline solar panel of Offgridtec 1030 x 520 x 35 mm 1 x Pair of solar connector compatible junction boxes for parallel connection of the two solar modules 1 x 30a pwm charge controller with clear lcd display and usb charging possibility - the device also has a 30a load output and is easy to operate - all important parameters can be read on the display 1 x 122Ah agm battery with m8 screw terminal Dimensions: 406 x 174 x 233 mm(+5mm terminal) - the battery is absolutely maintenance free and leak proof and lasts up to 10 years depending on use 1 x 1000w 12v to 230v sine wave voltage converter with a shockproof socket incl. connection cable - the rated power of 1000w can be output by the device for 15 minutes - beyond that the inverter outputs 800w and can handle short time starting currents up to 1600w 1 x 8m 6mm² professional connection cable solar module to charge controller with original Stäubli solar-connectors and high quality Lapp Ölflex 2x6mm² solar cable 1 x 1.5m 10mm² professional battery connection cable with MIDI fuse holder, 40a MIDI fuse and m8 ring terminals for connection between charge controller and battery 1 x Temperature sensor with 3m length for connection of the controller to the batrie 1 x 1m 25mm² connection cable from inverter to battery (included with the voltage converter) 1 x Fuse holder + 125A Mega fuse for installation between voltage transformer and battery positive pole for protection against short circuit Note and accessories recommendation If you plan to leave consumers permanently switched on at the voltage transformer, we recommend the use of an additional deep discharge protection. The voltage transformer switches off the connected consumer when undervoltage is reached - but not itself. In case of longer absence (e.g. over night) the battery can be deeply discharged by the self-consumption of the voltage converter and thus be irreparably damaged. In this case we recommend the use of a Victron Battery Protect battery protector. For the included voltage transformer the 100a version is sufficient. For the installation of the device between the voltage transformer and the battery, 1 short connection cable is needed. Roof mount for the solar module Since there are different requirements for the mounting of a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mount as standard. This can of course be purchased additionally - find suitable suggestions here: Solar module holder for flat roof or wall mounting Mounting kit for pitched roof mounting on roof tiles (Frankfurter Pfanne etc.) Mounting kit for pitched roof mounting on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure Fastening kit for pitched roof installation on Bieberschwanz tiles Scope of delivery: 1x Solaranlage Autark M-Master with 2x100w solar panel, 30a pwm charge controller with lcd display and usb ports, 1000w sine wave voltage converter, 122Ah agm battery, user manuals