The us3000c (mpn us3000c) is a lithium storage system of the latest generation. The accumulator was specially developed to fully meet the high demands placed on a solar accumulator today. Maximum safety and a long service life are guaranteed even with regular deep discharge thanks to the latest technology. The latest battery of the market-leading manufacturer with now 3.5 kWh per module has again a battery management system (bms) built into each module and therefore offers a lot of security. Internally, the individual cells are thus monitored and balanced against overvoltage, overtemperature, deep discharge, etc. protected. The battery is compatible and certified with many available inverters. Features Extremely cycle resistant - over 6000 cycles at 95% DoD More usable energy content than the previous model US3000 Lifetime over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging power possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function capable of reducing the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects each installed battery cell from harmful influences over the entire life of the module and effectively prevents premature failure. Protection against: Deep discharge and overcharge overvoltage during charging excessive currents during charging and discharging over and under temperature Short circuit and reverse polarity Constant monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the desired storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) accumulator and an integrated BMS. High cycle life The extremely high cycle life of the installed LiFePo4 cells make Pylontech us3000c modules the optimal storage solution for photovoltaic systems. Regardless of whether the solar system is grid-connected or stand-alone, the Pylontech storage system offers several advantages over typical lead-acid batteries and other lithium technologies. Technical data Battery Type: Lithium Iron Phosphate (LiFePo4) Rated voltage: 48V Rated capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (Discharge) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Temperature range charge: 0°C - +50°C Temperature range discharge: -10°C - +50°C Temperature range storage: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 years manufacturer warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by freight forwarding! Scope of delivery: 1x Pylontech us3000c LiFePO4 3.5 kWh 1x cable set parallel connection incl. grounding 1x rj45 data cable 1x mounting screws 1x user manual
From
€1,013.31*
From €851.52**
The us3000c (mpn us3000c) is a lithium storage system of the latest generation. The accumulator was specially developed to fully meet the high demands...
The Pytes e-box 48100r-c (mpn 110402100007) is a state-of-the-art LFP battery with 100 Ah capacity and is characterized by its high level of safety, sophisticated design and impressive performance. The battery is compact, easy to install, maintenance-free and can be used as the basic building block of an energy storage system by connecting it in parallel. Applications range from self-consumption coverage in private homes to small commercial and industrial energy storage systems, as well as in telecommunication stations.The Pytes E-BoxLatest generation LFP storageOver 6000 cycles at 90% DoDIntelligent energy managementIdeal for emergency power supplyExtensive compatibilityModularly expandableCAN and rs485 communicationIntelligent energy managementThe intelligent Pytes battery offers a comprehensive energy management system. Through real-time measurements, monitoring and management, it optimizes the system service life using intelligent algorithms. The battery thus ensures efficient and sustainable use of the available energy.Reliable emergency power supplyThe simple installation and user-friendly design make Pytes batteries a practical option for ensuring an uninterrupted power supply in your home. With their intelligent control features, Pytes batteries can optimize energy consumption and maximize battery life to ensure your backup power supply is efficient and reliable.Long service life and maximum safetyPytes batteries are characterized by their impressive service life and high level of safety. With over 6000 cycles at 90% depth of discharge (dod), they offer an exceptionally long service life. Whether it is a grid-connected solar system or a self-sufficient stand-alone system, the Pytes storage system offers several clear advantages over conventional lead batteries and other lithium technologies.Technical dataBattery chemistry: Lithium iron phosphate (LFP)Nominal voltage: 51.2 VVoltage range: 47.5-57.6 VNominal power: 100 AhNominal energy: 5.12 kWhMax. Charging current: 50 AMax. Discharge: 50 ACharging temperature: 0~50°CDischarging temperature: -10~50°CEfficiency: =95%Communication protocol: rs-232, rs-485, CANCycle life: >6000 cycles at 90% DoDDimensions: 440 x 620 x 117 mmWeight: 51 kgScope of delivery:1x Pytes E-Box 48100r-c
€1,307.81*
€1,099.00**
The Pytes e-box 48100r-c (mpn 110402100007) is a state-of-the-art LFP battery with 100 Ah capacity and is characterized by its high level of safety, s...
The Offgridtec MPPT Pro-Duo (MPN 1-01-011200) is an innovative high-end solar controller that was essentially designed for mobile applications. A variety of different board battery types can be charged via the primary charging output (BATT-1). The battery spectrum ranges from AGM, GEL and liquid lead acid to state-of-the-art LiFePO4 and Li-NiCoMn battery systems. The secondary battery charge output (BATT-2) is designed for a starter battery that is at the same voltage level as BATT-1. The unit automatically detects the system voltage of the starter battery (BATT-2) and charging of the BATT-2 begins as soon as the preset conditions are met.
The controller uses the advanced MPPT control algorithm that minimises the maximum power point loss rate and loss time, quickly tracks the maximum power point (MPP) of the PV generator, and processes the maximum energy from the PV generator under all conditions. Energy utilisation in a PV system with MPPT controller is increased by 20 to 30% compared to the PWM charging method.
Features Highlights of the MPPT Pro DUO 30 A
Max Power-Point Tracking technology with ultra-fast tracking speed and a guaranteed tracking efficiency of at least 99.5%.
Advanced MPPT control algorithm to minimise MPP loss rate and minimise time loss.
Higher range of MPP operating voltage to improve PV module utilisation.
Possibility of limiting the charging power by user or automatic charging current (BATT-1).
Digital circuit control of adaptive three-stage charging mode to improve BATT-1 lifetime.
The product will enter power saving mode if no manual input has been made for a long time and charging conditions are not met (PV<5v).>
100% charge and discharge in the operating temperature range.
AES control signal for auto-refrigerator to avoid energy waste.
Standard Modbus protocol and RS485 communication port (5V/200mA).
Overview of the most important technical features
Maximum charging current: 30A at a battery voltage of 12V or 24V.
Optional remote display with mounting frame available.
Supports all major battery types.
Active temperature equalisation for optimal charging and ensuring long battery life.
Max. Solar power 390W at 12V system voltage and 780W at 24V system voltage.
100V max. PV input voltage
Grounding: Negative
Dimensions: 24.7cm x 16.5cm x 6.9cm (LxWxH)
Connection terminals Battery 1: 16mm² (AWG6) / Battery 2: 4mm² (AWG12)
Weight: 1,4KG
Diameter of mounting holes: 5mm
Energy consumption: 26mA at 12V / 15mA at 24V
Max. Efficiency: 98
Intelligent energy saver
If there is no manual operation for an extended period of time and charging conditions are not present, the MPPT-Pro Duo will switch to energy saving mode, reducing the unit's energy consumption to a minimum. This behaviour also reduces wear and tear on the unit, which is reflected in a significantly longer service life. The system parameters are displayed and set directly via the intuitive control panel on the controller or via the MT11 remote control (accessory).
System communication and protection functions
The refrigerator's AES control signal is built into the controller, which delivers excess solar power to the refrigerator to prevent energy waste. The protection class of the MPPT Duo is IP33. It resists splashing water and is dust-tight. Our MPPT Pro DUO has multiple protection functions, including battery overcharge protection, discharge protection and reverse polarity protection of PV and battery, which effectively ensure the safety, stability and service life of the solar system.
Scope of delivery:
1x Offgridtec 1-01-011200 MPPT DUO charge controller.
1x instruction manual
€111.84*
€93.98**
The Offgridtec MPPT Pro-Duo (MPN 1-01-011200) is an innovative high-end solar controller that was essentially designed for mobile applications. A vari...
The Multiplus-II 48/3000/35-32 gx is a high-end device combination from victron Energy (mpn pmp482306000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and the potential range of use to ess applications. The inverter module delivers a whopping 3000 w at non-linear load, or 2400 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 35 a charging power, and is complemented by a 32 a transfer switch that allows lightning-fast switching between aC connections. Compared to the rest of the series, the gx variants have an integrated gx display with numerous other connection options. important features of the Multiplus-II 48/3000/35-32 gx integrated gx control unit with various communication ports PowerControl and Powerassist -increase of mains or generator performance built-in anti-islanding function and connection for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 3000w power at non-linear load 2400 w continuous load and 6000 w peak power for 48 v battery voltage, 32 a transfer switch and 35 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/3000/35-32 gx. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. Scope of the integrated gx device A vE.Can interface This can be used to connect vE.Can devices from victron (e.g. vE.Can mppt). The port can also be reconfigured via the remote console for use with a compatible CaN bus Li-Ion battery. 1xUSB connection 1x Ethernet port 1x vE.Direct connection many possibilities for system expansion Settings can be changed within minutes using the vEConfigure software (requires a computer or laptop and MK3 USB interface).multiple monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482306000 Multiplus-II 48/3000/35-32 gx 230 v 1x instruction manual
€800.10*
€672.35**
The Multiplus-II 48/3000/35-32 gx is a high-end device combination from victron Energy (mpn pmp482306000) that combines classic Multiplus components w...
The solar module 150w mono from Offgridtec (mpn 3-01-001255) works with monocrystalline solar cells with a high efficiency of >22,3% and is ideal for 12v systems thanks to its 20v operating voltage. In Offgridtec mono solar modules only cells of the highest quality grade are installed and guarantee a constant high quality and performance with maximum service life thanks to state-of-the-art manufacturing. Features of Offgridtec 150w 12v mono solar panel proven quality directly from Offgridtec manufactured according to the latest standards monocrystalline solar cells extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v systems on land or in mobile solar systems 2 bypass diodes - minimized power loss in shaded conditions The mono 150w 12v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtecs experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. It can withstand heavy hail and storms or extreme cold and heat without any problems and thanks to the integrated bypass diodes, the module can continue to produce power even in shaded or low light conditions. The most important technical data at a glance Power (Pmax): 150w Working voltage (Vmp): 20 V Open circuit voltage (Voc): 24 V max. current (Imp): 7.5 A Short circuit current (Isc): 8.1 A max. system voltage: 1000 V permissible ambient temperature: -40°C - +85°C Dimensions: 1140 x 680 x 35 mm Weight: 12 kg Universally applicable Offgridtecs 150w 12v Mono is universally applicable for example in 12 Volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. The connection cables are 80 cm long and equipped with MC4 connectors. Scope of delivery: Offgridtec 3-01-001255 150w mono 12v solar panel
€130.78*
€109.90**
The solar module 150w mono from Offgridtec (mpn 3-01-001255) works with monocrystalline solar cells with a high efficiency of >22,3% and is ideal f...
The fsp-2 195w 12v is the second largest and newest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in the range. It has a 3-sided design and comes with a matching connection kit that allows you to quickly and easily connect to the charge controller of your choice and the battery to be charged.
Performance that sets standards
The fsp-2 195w Ultra is equipped with American SPR back-contact cells from SunPower. The look of the cells is completely black, which also gives the fsp-2 195w a very modern, high-quality look. The SPR cells ensure a very high efficiency of the panel and set new standards in this power class in combination with the low weight and compact dimensions of the fsp-2 panel.
extensive application possibilities:
excellent usable in the camping area
or for expeditions, climbing tours and much more...
for vehicles and boats without fixed solar installation ...
and numerous other applications in different areas...
technical highlights fsp-2 195w ultra foldable solar panel
Rated power: 195wp
Number of sides: 3 x 65 Wp
Module voltage (Vmp): 33,5 V
Max. Charge current (Imp): 5,82 A
Open circuit voltage (Voc): 39,4 V
Short circuit current (Isc): 6,17 A
Dimensions closed: 820 x 440 x 40 mm
Dimensions open designed: 820 x 1545 x 60 mm
Weight: 7,12 Kg
ETFE coating
SunPower high performance cells
6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side
0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller)
1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on the battery side
Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse
the included Profi-Connection Kit
The connection kit included in the scope of delivery offers everything needed for a quick start-up of the mobile solar set. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller.
For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal crocodile clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse.
customizable on request
All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred.
about the fsp-2 series
As with all Offgridtec solar module series, high quality has been emphasized in the fsp-2 series. The fsp-2 195w works with highly effective solar cells. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp-2 series is coated with ETFE coating, which provides better protection and at the same time ensures very high light transmittance. Furthermore, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions.
Scope of delivery
1x Offgridtec fsp-2 195w 12v, 3-01-012680
1x Offgridtec fsp-2 Connection-Kit
€403.23*
€338.85**
The fsp-2 195w 12v is the second largest and newest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in...
Besides a 290ml cartridge this handy Dekalin adhesive-set also includes the Dekalin Dekavator, DEKACLEAN cloths and a sheet of very fine sandpaper for an ideal preparation of the surface.
Dekasyl MS-5 is a polymer-based adhesive with a high degree of adhesion and initial strength which is ideal for elastic connections of various components.Thanks to it's adhesive power the use of clamps is mostly unnecassary. The Dekasyl MS-5 also serves as sealent between similar materials or when mechanical connections are used.
Application:
Elastic connections and sealing for trains, caravans, trucks, cars,...
Glueing windows of buses, trains, caravans,...
Glueing of edge profiles (aluminium or polyester) of trailers
Glueing of polyester components with metal frame
Characteristics:
Free of solvents, isocyanate and PVC
Very UV- and age-resistant
Very high initial strength. Very high adhesion in general even without priming on various surfaces.
Constantly elastic within a temperature range of -40°C to +120°
Neutral, odorless and quick-setting
After skim-development paintable - normally this does not influence the setting-process
Compatible with most industrial painting systems, alkyd resin paint as well as dispersion paint (because of the many different types of industrial paints a material compatibility test is recommended)
We recommend to mount our spoilers and cable entries only with Dekasyl adhesive together with DEKAvator as this connection had the best outcome in a laboratory test.
Why Dekasyl?
Manufacturers of caravans like Fendt, Dethleffs, Burstner, Carthago, Pilote and Hymer use Dekalin-products in many different areas, for example as sealent for roofs, side panels, undercoating, glueing of PMMA-windows, sound-proofing, engine-covering, and many more.As a global partner of the caravan and camping industry Dekalin provides you with a wide range of latest technology and supports sellers in realizing their demands. They offer special solutions for sealing, glueing, damming and repairing.
Details:Glue color: blackDelivery scope: 1x cartridge 290ml Dekalin 6252412 Dekasyl MS-5 adhesive black, 1x sheet of sandpaper, 1x Dekalin Dekavator 6257812 bottle 30ml, DEKACLEAN cleaning cloths
Besides a 290ml cartridge this handy Dekalin adhesive-set also includes the Dekalin Dekavator, DEKACLEAN cloths and a sheet of very fine sandpaper for...
Dieses Set enthält alles was Sie brauchen um Module mit je max. 1m Breite auf einem Ziegeldach zu befestigen. Die enthaltenen Dach-Haken sind spezielle für Ziegeldächer konstruiert. Durch hochwertigste korrosionsfreie Materialien aus Edelstahl und Aluminium ist eine sichere und langlebige Montage gewährleistet.
Die Stücklisten der Befestigungskits sind für eine Montage der Module direkt nebeneinander konzipiert. Sollten Sie z.B. zwei Reihen untereinander mit je drei Solarmodulen planen benötigen Sie zwei Kits für je drei Module.
Beinhaltet:
Dachhaken 3-fach verstellbar (Edelstahl)
Solar-Profilschienen (Aluminium)
Endklemmen (Aluminium)
Nutensteine (Aluminium)
Endkappen
Alle notwendigen Schrauben und Muttern
Hinweis:
Nur für gerahmte Module mit 30mm/35mm Rahmenstärke
Module sind nicht im Lieferumfang enthalten
Variants from €106.95*
€255.45*
€214.66**
Dieses Set enthält alles was Sie brauchen um Module mit je max. 1m Breite auf einem Ziegeldach zu befestigen. Die enthaltenen Dach-Haken sind spe...
The Autark M-Master is the medium sized complete system of the Autark family and delivers an average daily yield of 800 watt hours between March and October. The generated power is stored in the cycle-proof 122Ah agm battery - the high-quality charge controller with integrated display gives you information about the charge status of the battery while your 230v consumers can be operated at the sine wave voltage converter. Of course, the whole thing is delivered including a professional connection cable kit - plug it together and get started. The system is suitable for a wide range of applications - from 12v lighting, charging laptop, cell phone and camera batteries and other small consumers, to 230v household appliances with a maximum continuous power of 1000w (15min)
Features of the Autark M-Master
If required, module side expandable by 2 x 100w with low installation effort
Average daily yield between March and October: approx. 800wh (approx. 66Ah)
Plug & Play ready-to-connect system - plug together and go
Allows operation of 12v and 230v loads, as well as 5v usb consumers
usb charging possibility directly at the charge controller (max. 2,4A)
Easy to read lcd display informs about all operating parameters
Flexible mounting possibility thanks to 8m connection cable from module to controller
Extensive electronic protection functions, such as overload protection, overtemperature protection, undervoltage shutdown, short-circuit protection, reverse polarity protection, etc.
rs485 communication port on the voltage transformer offers extensive configuration possibilities via pc (interface cable rs485 to usb included)
Charge controller enables temperature compensated charging - temperature sensor included in delivery
Configurable 12v load output at the charge controller for loads up to max. 30a - suitable e.g. for lighting control
Application areas
This complete system can be used in many ways. Whether as a stationary system on the mountain hut or in the allotment garden - the permanent operation of small coolers and refrigerators, as well as the charging of cell phones and laptops succeeds easily with this system. The installation on the motor home is also conceivable - we also have the corresponding brackets and adhesive sets for the attachment.
Extensive connection options
230v ac 50hz 1000w (15min - 1000w / permanent - 800w / short time (starting currents) - 1600w) Schuko socket on the sine wave voltage converter
12v consumer output with 30a power directly at the charge controller
2 x usb charging port at the charge controller with max. 2.4a (total)
1 x usb charging port at the voltage converter with max. 1a power
Parts list - what's inside
2 x Offgridtec 100w V2 Solarpanel 23V black frame
1 x Pair of solar connector compatible junction boxes for parallel connection of the two solar modules
1 x 30a pwm charge controller with clear lcd display and usb charging possibility - the device also has a 30a load output and is easy to operate - all important parameters can be read on the display
1 x 122Ah agm battery with m8 screw terminal Dimensions: 406 x 174 x 233 mm(+5mm terminal) - the battery is absolutely maintenance free and leak proof and lasts up to 10 years depending on use
1 x 1000w 12v to 230v sine wave voltage converter with a shockproof socket incl. connection cable - the rated power of 1000w can be output by the device for 15 minutes - beyond that the inverter outputs 800w and can handle short time starting currents up to 1600w
1 x 8m 6mm² professional connection cable solar module to charge controller with original Stäubli solar-connectors and high quality Lapp Ölflex 2x6mm² solar cable
1 x 1.5m 10mm² professional battery connection cable with MIDI fuse holder, 40a MIDI fuse and m8 ring terminals for connection between charge controller and battery
1 x Temperature sensor with 3m length for connection of the controller to the batrie
1 x 1m 25mm² connection cable from inverter to battery (included with the voltage converter)
1 x Fuse holder + 125A Mega fuse for installation between voltage transformer and battery positive pole for protection against short circuit
Roof mount for the solar module
Since there are different requirements for the mounting of a module and this varies greatly depending on the type of roof, the systems of the Autark series are not equipped with a roof mount as standard. This can of course be purchased additionally - find suitable suggestions here:
Solar module holder for flat roof or wall mounting
Mounting kit for pitched roof mounting on roof tiles (Frankfurter Pfanne etc.)
Mounting kit for pitched roof mounting on roofing felt, corrugated hernite and sheet metal roofs with wooden substructure
Fastening kit for pitched roof installation on Bieberschwanz tiles
Scope of delivery:
1x Solaranlage Autark M-Master with 2x100w solar panel, 30a pwm charge controller with lcd display and usb ports, 1000w sine wave voltage converter, 122Ah agm battery, user manuals
€741.44*
€623.06**
The Autark M-Master is the medium sized complete system of the Autark family and delivers an average daily yield of 800 watt hours between March and O...
Extremely versatile complete package The Offgridtec® HomePremium series is a true all-rounder at an unbeatable price-performance ratio. As well as being used as a usv backup solution with a choice between mains and battery priority, this PV system can also be used as a self-consumption system. There are virtually no limits to the performance of this Solarasystem - depending on personal requirements and on request, extensions are possible, both on the module and battery side. if a higher output power is required on the inverter, additional identical devices can also be connected here to increase performance. In addition to the power electronics, the storage system and the solar modules, all components required for the connection are also included in the scope of delivery, with the exception of the solar module holder, which must be ordered separately. all other components are plug and play - this means no annoying plug installation or the like - connect and you're done. Depending on your choice, the system is supplied with or without an electricity meter. Parts list - what's inside 30x Luxen Solar 430w Full Black Solar panel Luxneri Series 5 4 x 4.8kwh Pylontech us5000 LiFePo4 storage batteries 1x victron Energy mppt SmartSolar charge controller 450/200 48v 3x victron pmp482505010 Multiplus-II 48/5000/70-50a 1x Cerbo gx + 1x gx Touch 50 from victron Energy - the communication center of your system 1x victron Energy Lynx Distributor for dc distribution and protection 1x victron Energy Lynx Power In 3x 10m Offgridtec® Professional connection cable 6mm² solar module to charge controller for the connection between solar modules and charge controller 2 x Pylontechbattery connection cable set Pylontech to inverter 2 x 2.0m 25mm² amphenol to m8 1x 1m battery cable 50mm² m8 eyelets on both sides 3x 1m battery cable 35mm² m8 eyelets on both sides 3x 10m 6mm² mc-4 connection cable 1x vE.Can to CaN-Bus bms Type a cable 1.8m aSS030710018 for connecting the Cerbo gx to the memory 2x 3m victron rj45 utp cable for connecting the MultiPlus to the Cerbo gx 3x Mega fuse 125a / 70v 1x Mega fuse 250a / 70a 2x 0.9m victron rj45 utp cable 1x Pylontech Battery cabinet for us5000 When selecting electricity meter: 1x victron vm-3p75ct Energy Meter 1x victron 5m rj45 utp cable Extended use of your HomePremium system The HomePremium system is supplied either with or without victron electricity meter and cable, whereby an energy meter with connection cable is mandatory for the installation of an Energy Storage System. With this electricity meter, you can carry out a grid-parallel installation and then monitor your energy consumption and control your energy costs. thanks to phase compensation, you can even use the 3-phase meter for 1-phase systems. This means that seamless integration of decentralized energy sources and consumers into the existing power grid is no problem. Luxen Solar 430w Full Black solar module The monocrystalline and bifacial 430w Full Black Series n5 solar module fromLuxen Solarsolar module impresses with a combination of different technologies, such as N-TOPCon cell technology and a 108 half-cell layout. The smbb half-cut cell technology was also used during production to increase performance. The state-of-the-art solar module represents the pinnacle of solar technology, offering impressive power output and low LCOE. Features Glass-glass module N-TOPCon cell technology smbb Half-Cut cell technology Low bos & LCOE Bifacial cell module technology excellent anti-PID and low lid performance 3 bypass diodes 30-year performance guarantee and 15-year product guarantee high cell efficiency of over 22% Half-cell technology In half-cell technology ("half-cut"), conventional silicon cells are cut in half using a laser. The resulting halves are then centrally connected in parallel, which leads to an increased output of the solar module by reducing resistance losses. Bifacial cells Bifacial means two-faced. And the name says it all: the Luxen Solar 430w n5 module is also equipped with solar cells on the back, which means that sunlight can be absorbed even better and the efficiency of the overall module is increased. Technical data maximum output: 430w Module voltage (vmp): 32.04v max. current (imp): 13.42a Open circuit voltage (voc): 38.96v Short-circuit current (Isc): 14.13a Module efficiency: 22.02% dimensions: 1722 x 1134 x 30 mm Operating temperature range: -40°C to +85°C Cells: 108 (6x18) max. operating voltage: 1500v dc Weight: 23,5kg LiFePo4 storage technology from Pylontech - proven, reliable, safe The us3000c storage battery from Pylontech is a latest-generation lithium iron phosphate battery that offers maximum safety and service life. Each module has a battery management system (bms) for comprehensive protection against deep discharge, overcharging and damage caused by high currents or extreme temperatures. Short circuits and reverse polarity are also excluded. Features of the Pylontech us3000c memory modules Extremely cycle-proof - over 6000 cycles at 95% DoD (discharge per cycle) absolutely intrinsically safe due to integrated protective shutdown (bms) High charging and discharging capacity of up to 5kw per module High storage density Low weight and compact design absolutely maintenance-free and easy to install 10-year guarantee The heart of the system - the victron MultiPlus-II 48/5000 The Multiplus-II 48/5000/70-50 from victron Energy combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100a and enables use in ESS applications. The setting options on the MultiPlus-II are extremely varied, as are its possible applications. We have already made the most important settings for you so that the system, as it is supplied, lives up to the description "Plug and Play" - the system can therefore be used immediately without any further configuration. Performance features and characteristics of the MultiPlus-II 48/5000 PowerControl and Powerassist - increasing mains or generator output Built-in anti-islanding function and connection option for external current sensor (optional) Can be used as a backup device in grid-connected systems vE.Bus interface for parallel and three-phase operation Remote monitoring and system integration Parallel and three-phase operation Approved according to vde-ar-n 4105 Technical data 5000 w power with non-linear load - 4000 w continuous load - 9000 w peak power For 48 v battery voltage, 50 a transfer switch and 70a battery charger output voltage: 230 vaC, frequency: 50 Hz Max. efficiency: 95% Protection class IP22 Maximum flexibility thanks to two AC outputs The MultiPlus-II offers uninterrupted operation by automatically taking over the supply to consumers in the event of mains failures or interruptions to the shore/generator power. The switchover takes place in less than 20 milliseconds to ensure continuous operation of electronic devices. A second output supplies power only when alternating current is present at the input of the MultiPlus-II. This makes it possible to connect consumers such as a water heater that should not be discharged from the battery. Configuration The MultiPlus-II is supplied unconfigured as standard. You can find the configuration instructions for the system here in the download area. If you would like us to pre-configure the system, we can do this for you for an additional charge. To do this, place the article linked above "Offgridtec pre-configuration" in the shopping cart during the ordering process. In this case, shipping may take 3-5 working days longer until the configuration has been completed. victron Energy Cerbo gx and gx Touch 50 - the communication center of your system The latest development in system monitoring from the company allows you to control and configure your system with ease. rounded off by the gxC Touch 50 - a waterproof 5 inch touchscreen - you always have an overview of your system parameters. The Cerbo's functions allow you to control and monitor your system perfectly and maximize system performance in an unprecedentedly simple way. victron Energy has developed a new system monitor that allows you to easily control and configure your system. The gx Touch 50, a waterproof 5-inch touchscreen, provides a clear overview of your system parameters. The Cerbo module allows you to precisely monitor your system and maximize performance. It is compatible with both solar charge controllers and grid-connected inverters. Mounting material and connection cable are included in the scope of delivery. The Bluetooth function of the gx Touch 50 makes accessing your system even quicker and easier. An optional wall bracket is available. victron Remote portal The victron Remote Portal (vRM) is a free victron Energy service that allows you to read out your system data remotely and configure the devices accordingly. This means that you always have full control and an overview of all relevant system parameters, even when you are away. The functionality is available online as a demo version and is ideal for getting a first impression - https://vrm.victronenergy.com/landingpage Safety note: Only have this complete system installed and commissioned by a qualified electrician.
Variants from €16,173.02*
€0.00*
€0.00**
Extremely versatile complete package The Offgridtec® HomePremium series is a true all-rounder at an unbeatable price-performance ratio. As well a...
The Steca Solarix 2020-x2 is a state-of-the-art dual-battery charge controller ideal for recreational and RV use. It has a solar panel input, which is suitable for all 36-cell solar modules in 12 V systems or all 72-cell crystalline solar modules in 24 V systems. Both the main battery and the starter battery are permanently and simultaneously charged by the solar module In the process, 90 percent of the available power flows into the main battery, while the secondary battery is kept at the full charge level with 10 percent of the power Using the Steca pa lcd1 remote display, the distribution of the charging power can be changed. The charge controller has a powerful load output that is fed only from the main battery There is a USB charging socket on the charge controller, which can be used to charge smartphones and tablets as well. Optionally, the Steca pa lcd1 remote display can be connected The Steca Solarix 2020-x2 is a state-of-the-art dual-battery charge controller that is ideal for recreational and RV use. It features a solar panel input, which is suitable for all 36-cell solar modules in 12 V systems or all 72-cell crystalline solar modules in 24 V systems. Both the main battery and the starter battery are permanently and simultaneously charged by the solar module In the process, 90 percent of the available power flows into the main battery, while the secondary battery is kept at the full charge level with 10 percent of the power Using the Steca pa lcd1 remote display, the distribution of the charging power can be changed. The charge controller has a powerful load output that is fed only from the main battery There is a USB charging socket on the charge controller, which can be used to charge smartphones and tablets as well. Optionally, the Steca pa lcd1 remote display can be connected The Steca Solarix 2020-x2 is a state-of-the-art dual-battery charge controller that is ideal for recreational and RV use. It features a solar panel input, which is suitable for all 36-cell solar modules in 12 V systems or all 72-cell crystalline solar modules in 24 V systems. Both the main battery and the starter battery are permanently and simultaneously charged by the solar module In the process, 90 percent of the available power flows into the main battery, while the secondary battery is kept at the full charge level with 10 percent of the power Using the Steca pa lcd1 remote display, the distribution of the charging power can be changed. The charge controller has a powerful load output that is fed only from the main battery There is a USB charging socket on the charge controller, which can be used to charge smartphones and tablets as well. Optionally, the Steca pa lcd1 remote display can be connected
€125.70*
€105.63**
The Steca Solarix 2020-x2 is a state-of-the-art dual-battery charge controller ideal for recreational and RV use. It has a solar panel input, ...
The Steca PRS 2020 charge controller is perfectly suited for PV-systems to charge 12V or 24V lead batteries.
Protection functions:
overload
deep discharge
battery undervoltage
current reflow into the module
Protection from application errors:
short-circuit/reverse polarity at solar module
short-circuit at consumer output (excessive consumption)
reverse polarity at battery
overcurrent at solar module
overtemperature
overvoltage at consumer output
wrong connection order
Note:
The default battery type can only be adjusted with additional equipment (Steca PA PR100).The PRS-series's default battery type is lead-acid (liquid).If you want to use the controller to charge AGM or gel batteries please use the contact formular during your order or contact our customer: [email protected] / +49 (0) 8721 98297-40
€69.90*
€58.74**
The Steca PRS 2020 charge controller is perfectly suited for PV-systems to charge 12V or 24V lead batteries.
Protection functions:
overload
deep ...
The Steca PRS3030 charge controller is perfectly suited for PV-systems to charge 12V or 24V lead batteries.
Protection functions:
overload
deep discharge
battery undervoltage
current reflow into the module
Protection from application errors:
short-circuit/reverse polarity at solar module
short-circuit at consumer output (excessive consumption)
reverse polarity at battery
overcurrent at solar module
overtemperature
overvoltage at consumer output
wrong connection order
Note:The default battery type can only be adjusted with additional equipment (Steca PA PR100).The PRS-series's default battery type is lead-acid (liquid).If you want to use the controller to charge AGM or gel batteries please use the contact formular during your order or contact our customer: [email protected] / +49 (0) 8721 98297-40
€74.90*
€62.94**
The Steca PRS3030 charge controller is perfectly suited for PV-systems to charge 12V or 24V lead batteries.
Protection functions:
overload
deep d...
The Steca PR 2020 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped with a LCD display which makes it easy to control the device's funtions and shows all current working parameteres.
Generally the controller is only usable with the following battery types:- lead-accumulators with liquid electrolytes- sealed lead-accumulators, AGM, gel- 12V and 24V consumers, which can be directly connected to the controller (right connection pair)
Protection functions:- protection from reverse polarized modules- protection from reverse polarized consumers- protection from reverse polarized batteries- prevents from battery charge and discharge- short-circuit protection on module input- short-circuit protection on load output- protection from a to high charging current- no-load working test without battery or consumer- current reflow protection- over/undervoltage protection- overheating protection- deep discharge protection- CE-compliant
€99.90*
€83.95**
The Steca PR 2020 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped ...
Features:- serial-controller- voltage regulation- automatic voltage adjustment- PWM-regulation- multistep charge technology- current compensated shutdown threshold (loads)- automatic load restart- temperature compensation- joint positive or negative grounding of one clamp- monthly maintenance charge
Protection functions:- overload- deep discharge- reverse polarity of module, load and battery- automatic electronical fuse- short-circuit- overvoltage at module input- no-load protection without battery- current reflow at night- overtemperature and overload protection- shutdown at battery overvoltage
NOTE: Battery type can only be changed with optional equipment (Steca PA RC100).The default battery type is AGM-/gel-battery.If you want to use this controller to charge a lead-acid battery please let us know via emai or phone.
€29.00*
€24.37**
Features:- serial-controller- voltage regulation- automatic voltage adjustment- PWM-regulation- multistep charge technology- current compensated shutd...
The solar charge controller Steca Solsum 4040 is a further development of our internationally popular Solarix prs controller family. Thanks to the increased module and load current, they are now also suitable for even larger systems In addition, the devices have an integrated USB charging socket on which smartphones and tablets can be charged. They impress with their simplicity, performance and unbeatable price-performance ratio Several LEDs in different colors provide information about the battery's charge status at a glance. Modern Steca algorithms are used to ensure optimum battery care The Steca Solsum charge controllers are equipped with an electronic fuse for optimum protection. They work on the serial principle and disconnect the solar module from the battery to protect against overcharging For larger projects, charge controllers can also be equipped with special functions: e.g. night light function and selectable charge termination and deep discharge protection voltages The solar charge controller Steca Solsum 4040 is a further development of our internationally popular Solarix prs controller family. Thanks to the increased module and load current, they are now also suitable for even larger systems In addition, the devices have an integrated USB charging socket on which smartphones and tablets can be charged. They impress with their simplicity, performance and unbeatable price-performance ratio Several LEDs in different colors provide information about the battery's charge status at a glance. Modern Steca algorithms are used to ensure optimum battery care The Steca Solsum charge controllers are equipped with an electronic fuse for optimum protection. They work on the serial principle and disconnect the solar module from the battery to protect against overcharging For larger projects, charge controllers can also be equipped with special functions: e.g. night light function and selectable charge termination and deep discharge protection voltages The solar charge controller Steca Solsum 4040 is a further development of our internationally popular Solarix prs controller family. Thanks to the increased module and load current, they are now also suitable for even larger systems In addition, the devices have an integrated USB charging socket on which smartphones and tablets can be charged. They impress with their simplicity, performance and unbeatable price-performance ratio Several LEDs in different colors provide information about the battery's charge status at a glance. Modern Steca algorithms are used to ensure optimum battery care The Steca Solsum charge controllers are equipped with an electronic fuse for optimum protection. They work on the serial principle and disconnect the solar module from the battery to protect against overcharging For larger projects, charge controllers can also be equipped with special functions: e.g. night light function and selectable charge termination and deep discharge protection voltages
€89.90*
€75.55**
The solar charge controller Steca Solsum 4040 is a further development of our internationally popular Solarix prs controller family. Thanks to the inc...
The Steca PR 2020 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped with a LCD display which makes it easy to control the device's funtions and shows all current working parameteres.
Generally the controller is only usable with the following battery types:- lead-accumulators with liquid electrolytes- sealed lead-accumulators, AGM, gel- 12V and 24V consumers, which can be directly connected to the controller (right connection pair)
Protection functions:- protection from reverse polarized modules- protection from reverse polarized consumers- protection from reverse polarized batteries- prevents from battery charge and discharge- short-circuit protection on module input- short-circuit protection on load output- protection from a to high charging current- no-load working test without battery or consumer- current reflow protection- over/undervoltage protection- overheating protection- deep discharge protection- CE-compliant
€84.89*
€71.34**
The Steca PR 2020 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped ...
The Steca PR 3030 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped with a LCD display which makes it easy to control the device's funtions and shows all current working parameteres.
Generally the controller is only usable with the following battery types:
- lead-accumulators with liquid electrolytes- sealed lead-accumulators, AGM, gel- 12V and 24V consumers, which can be directly connected to the controller (right connection pair)
Protection functions:
- protection from reverse polarized modules- protection from reverse polarized consumers- protection from reverse polarized batteries- prevents from battery charge and discharge- short-circuit protection on module input- short-circuit protection on load output- protection from a to high charging current- no-load working test without battery or consumer- current reflow protection- over/undervoltage protection- overheating protection- deep discharge protection- CE-compliant
€119.90*
€100.76**
The Steca PR 3030 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped ...
The solar charge controller Steca Solsum 2525 is a further development of our internationally popular Solarix prs controller family. Thanks to the increased module and load current, they are now also suitable for even larger systems In addition, the devices have an integrated USB charging socket on which smartphones and tablets can be charged. They impress with their simplicity, performance and unbeatable price-performance ratio Several LEDs in different colors provide information about the battery's charge status at a glance. Modern Steca algorithms are used to ensure optimum battery care The Steca Solsum charge controllers are equipped with an electronic fuse and thus offer optimum protection. They work on the serial principle and disconnect the solar module from the battery to protect against overcharging For larger projects, charge controllers can also be equipped with special functions: e.g. night light function and selectable charge termination and deep discharge protection voltages The solar charge controller Steca Solsum 2525 is a further development of our internationally popular Solarix prs controller family. Thanks to the increased module and load current, they are now also suitable for even larger systems In addition, the devices have an integrated USB charging socket on which smartphones and tablets can be charged. They impress with their simplicity, performance and unbeatable price-performance ratio Several LEDs in different colors provide information about the battery's charge status at a glance. Modern Steca algorithms are used to ensure optimum battery care The Steca Solsum charge controllers are equipped with an electronic fuse and thus offer optimum protection. They work on the serial principle and disconnect the solar module from the battery to protect against overcharging For larger projects, charge controllers can also be equipped with special functions: e.g. night light function and selectable charge termination and deep discharge protection voltages The solar charge controller Steca Solsum 2525 is a further development of our internationally popular Solarix prs controller family. Thanks to the increased module and load current, they are now also suitable for even larger systems In addition, the devices have an integrated USB charging socket on which smartphones and tablets can be charged. They impress with their simplicity, performance and unbeatable price-performance ratio Several LEDs in different colors provide information about the battery's charge status at a glance. Modern Steca algorithms are used to ensure optimum battery care The Steca Solsum charge controllers are equipped with an electronic fuse and thus offer optimum protection. They work on the serial principle and disconnect the solar module from the battery to protect against overcharging For larger projects, charge controllers can also be equipped with special functions: e.g. night light function and selectable charge termination and deep discharge protection voltages
€74.90*
€62.94**
The solar charge controller Steca Solsum 2525 is a further development of our internationally popular Solarix prs controller family. Thanks to th...
Designed for the use with Steca Solsum F, Steca Solarix PRS und Steca Solarix MPPT 2010.
With this remote you can program your Steca solar charge controller. By using its switches all parameters can be adjusted according to your demands.After a restart and pressing the program-button the adjustments are activated.
Details:
low weight
easy installation
maintenance-free
low consumption
very reliable
nightlight function ex works or adjustable via PA RC100
adjustment of parameters
Adjustable Parameters:
battery type: gel/liquid
night-light function
end of charge voltage (float/boost/equal)
deep discharge protection (LVD)
restart threshold
€119.90*
Designed for the use with Steca Solsum F, Steca Solarix PRS und Steca Solarix MPPT 2010.
With this remote you can program your Steca solar charge con...
The remake of the Steca Tarom sets new standards in this performance class. A grafical display shows all relevant working data and allows the controller's configuration and adjustmentto the requirements of the system.
Thanks to an improved charging level measurement the system is optimally regulated and a connected battery is much better protected.The Steca Tarom charge controller is the first choice for systems up to 2400W on different voltages (12V and 24V).
An integrated data logger saves all important system data which can be read out through a RS232-interface. Optionally a temperature sensor can be connected.
Two additional switching contacts are freely configurable as timer, nightlight-function, to start generators or as surplus manager.
€269.90*
€226.81**
The remake of the Steca Tarom sets new standards in this performance class. A grafical display shows all relevant working data and allows the controll...
The Steca Solsum-F-generation is one of the most used charge controllers in the field of solar home systems.A multifunctional LED-display allows the quick and easy use of the device.
Features:- serial-controller- voltage regulation- automatic voltage adjustment- PWM-regulation- multistep charge technology- current compensated shutdown threshold (loads)- automatic load restart- temperature compensation- joint positive or negative grounding of one clamp- monthly maintenance charge
Protection functions:- overload- deep discharge- reverse polarity of module, load and battery- automatic electronical fuse- short-circuit- overvoltage at module input- no-load protection without battery- current reflow at night- overtemperature and overload protection- shutdown at battery overvoltage
NOTE: Battery type can only be changed with optional equipment (Steca PA RC100).The default battery type is AGM-/gel-battery.If you want to use this controller to charge a lead-acid battery please let us know via emai or phone.
€21.90*
€18.40**
The Steca Solsum-F-generation is one of the most used charge controllers in the field of solar home systems.A multifunctional LED-display allows the q...
The Steca Solsum-F-generation is one of the most used charge controllers in the field of solar home systems.Ideal for small solar systems with less than 10A current.
Features:
serial-controller
voltage regulation
automatic voltage adjustment
PWM-regulation
multistep charge technology
current compensated shutdown threshold (loads)
automatic load restart
temperature compensation
joint positive or negative grounding of one clamp
monthly maintenance charge
Protection functions:
overload
deep discharge
reverse polarity of module, load and battery
automatic electronical fuse
short-circuit
overvoltage at module input
no-load protection without battery
current reflow at night
overtemperature and overload protection
shutdown at battery overvoltage
NOTE: Battery type can only be changed with optional equipment (Steca PA RC100).The default battery type is AGM-/gel-battery.If you want to use this controller to charge a lead-acid battery please let us know via emai or phone.
€37.90*
€31.85**
The Steca Solsum-F-generation is one of the most used charge controllers in the field of solar home systems.Ideal for small solar systems with less th...
The Steca PR 1010 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped with a LCD display which makes it easy to control the device's funtions and shows all current working parameteres.
Generally the controller is only usable with the following battery types:- lead-accumulators with liquid electrolytes- sealed lead-accumulators, AGM, gel- 12V and 24V consumers, which can be directly connected to the controller (right connection pair)
Protection functions:- protection from reverse polarized modules- protection from reverse polarized consumers- protection from reverse polarized batteries- prevents from battery charge and discharge- short-circuit protection on module input- short-circuit protection on load output- protection from a too high charging current- no-load working test without battery or consumer- current reflow protection- over/undervoltage protection- overheating protection- deep discharge protection- CE-compliant
€74.90*
€62.94**
The Steca PR 1010 was designed for photovoltaic systems to charge 12V and 24V batteries. In contrary to the Steca PRS seriesthe PR series is equipped ...
With 4 end clamps modules can be mounted on profile rails.
Features:
material: aluminuium
opening for M8 screws
frame height of 35mm
dimensions: 70 x 30 x 39mm
€1.27*
€1.07**
With 4 end clamps modules can be mounted on profile rails.
Features:
material: aluminuium
opening for M8 screws
frame height of 35mm
dimensions...
The bc01 Female from Betteri (mpn bc01B) is used for connection to a Envertech-, Hoymiles- or Huayu inverter. The opposite side can be connected to a h07rn-f rubber hose cable with a diameter of 10-14mm. It is a three-pole socket made of UV-resistant material. In addition, it is dustproof and waterproof according to protection class ip67, making it suitable for indoor and outdoor use. Product features Suitable for 1-phase inverters from e.g. Envertech, Hoymiles or Huayu Suitable for cables with a diameter of 10-14mm Dust and waterproof according to ip67 UV resistant - Suitable for indoor and outdoor installation Technical features Number of poles: 3-pole Material: plastic Operating temperature range: -40°C - +85°C Rated voltage: 230v AC Rated current: 25A Dimensions: 85.5 x 34.8 x 34.8 mm Weight: approx. 50g Scope of delivery: 1x Betteri bc01 female power plug
€5.34*
€4.49**
The bc01 Female from Betteri (mpn bc01B) is used for connection to a Envertech-, Hoymiles- or Huayu inverter. The opposite side can be connected to a ...
The end cap of Betterie (mpn bc01c) is used to close the unused 3 pole AC socket of the PV inverter of e.g. Envertech, Hoymiles or Huayu. Product features Suitable for 1-phase inverter from e.g. Envertech, Hoymiles or Huayu Closure of Betteri bc01 Female connector Dust and waterproof according to ip67 UV resistant - Suitable for indoor and outdoor mounting Scope of delivery: 1x Betteri Closure cap for bc01 socket
€3.56*
€2.99**
The end cap of Betterie (mpn bc01c) is used to close the unused 3 pole AC socket of the PV inverter of e.g. Envertech, Hoymiles or Huayu. Product f...
Dekasyl MS-5 is a polymer-based adhesive with a high degree of adhesion and initial strength which is ideal for elastic connections of various components.Thanks to it's adhesive power the use of clamps is mostly unnecassary. The Dekasyl MS-5 also serves as sealent between similar materials or when mechanical connections are used.
Application:
Elastic connections and sealing for trains, caravans, trucks, cars,...
Glueing windows of buses, trains, caravans,...
Glueing of edge profiles (aluminium or polyester) of trailers
Glueing of polyester components with metal frame
Characteristics:
Free of solvents, isocyanate and PVC
Very UV- and age-resistant
Very high initial strength. Very high adhesion in general even without priming on various surfaces.
Constantly elastic within a temperature range of -40°C to +120°
Neutral, odorless and quick-setting
After skim-development paintable - normally this does not influence the setting-process
Compatible with most industrial painting systems, alkyd resin paint as well as dispersion paint (because of the many different types of industrial paints a material compatibility test is recommended)
We recommend to mount our spoilers and cable entries only with Dekasyl adhesive together with DEKAvator as this connection had the best outcome in a laboratory test.
Why Dekasyl?
Manufacturers of caravans like Fendt, Dethleffs, Burstner, Carthago, Pilote and Hymer use Dekalin-products in many different areas, for example as sealent for roofs, side panels, undercoating, glueing of PMMA-windows, sound-proofing, engine-covering, and many more.As a global partner of the caravan and camping industry Dekalin provides you with a wide range of latest technology and supports sellers in realizing their demands. They offer special solutions for sealing, glueing, damming and repairing.
Details:Filling: 290mlMPN: 6252212Color: whiteDelivery scope: 1 tube 290ml
Dekasyl MS-5 is a polymer-based adhesive with a high degree of adhesion and initial strength which is ideal for elastic connections of various compone...
Dekaseal 8936 from Dekalin is the classic sealant. The dab-on sealant impresses with high tightness, uv-resistance, as well as elasticity, since it does not harden and remains somewhat permanently tacky. Optimal for use in applications without visible joint edges (flaps, hatches, side windows, keder strips, exterior sockets, etc.). The simple processing convinces professionals and laymen alike. There is no need for additional cleaning work, as protruding rust can be easily removed by dabbing without leaving any residue. The sealant can be used without pretreatment on clean, dry, dust- and grease-free surfaces used in vehicle construction/caravaning. Dekaseal 8936 can be applied by hand or with the aid of a compressed air gun. Its strengths, apart from its high impermeability, are that it is easy to dismantle, i.e. it is well suited for connections that need to be undone at a later date. Applications Sealing of overlaps and joints in e.g. bus, caravan, motor home, train and truck construction Sealing of screw connections Sealing of sun roof systems Application under facing strips for installation of windows and skylights in caravans and motor homes, trailers and in container construction Suitable for application between metal plates, glass, gfk, wood and other materials Sealing rubber-glass joints in buses, cars, trains and trucks Properties Very low water vapor permeability (0.1 - 0.2 g/day/m²) excess Dekaseal 8936 can be easily removed after a few minutes Very good uv aging resistance, proven quality Resistant to water, road salt, weathering influences Sealant must be fixed between a mechanical joint Generally good adhesion to most substrates without pretreatment Long shelf life, unopened min. two years Cannot be overpainted Adhesion In general, Dekaseal 8936 adheres well without pretreatment to clean, dry, dust and grease free substrates of aluminum, stainless steel, zinc, copper, brass, powder coated metal, most painted metal surfaces, glass, pvc, polyester (grp), painted wood and other surfaces. No adhesion without pretreatment on polyethylene, polypropylene and Teflon®. For properties on substrates not mentioned and further information, please contact Dekalin. Processing Dekaseal 8936 can be applied by hand or with a compressed air gun. When using compressed air, 2 - 3 bar are required. The areas to be sealed must be solid, clean, dry and free of grease. Paint and smooth into joints, crevices, etc. excess material can be dabbed off with itself after a short flash-off time. The material can be removed with turpentine substitute. The sealant remains slightly tacky after drying, but is odorless and compatible with paint. Technical data Base material: polyisobutene, synthetic resins, fillers and solvents Specific gravity (20°C), din 51757: approx. 1.4 kg/liter Temperature resistance: -30°C - +100°C Application temperature: +5°C - +35°C Color: anthracite Packaging size: 310ml cartridge Scope of delivery: 1x Dekalin Dekaseal 8936 cartridge 310ml anthracite
Dekaseal 8936 from Dekalin is the classic sealant. The dab-on sealant impresses with high tightness, uv-resistance, as well as elasticity, since it do...
The hm-350 from Hoymiles is the perfect micro inverter for your balcony power plant. The compact lightweight (only 1.98kg including the 1.35m AC cable) is suitable for solar power production with a solar panel up to 440 watts peak. Just like all other microinverters from Hoymiles, it is suitable for long operating hours and wide PV panel application because its startup is very low (only 22v) and the DC input range of the operating voltage (16-60V) is extremely wide.
Features
Minimize the effects of e.g. shading, dust or aging due to mppt
High-quality energy harvesting with high mppt accuracy
Optimal system reliability
Peak efficiency of 96.7%
12-year product warranty
High level of security thanks to integrated protection functions
Easy installation
Long service life
6000V surge protection
Complies with vde-ar-n 4105: 2018 and EN50549-1:2019
Optionally possible: Monitoring via S-Miles App or S-Miles Cloud
A DTU Lite is required for system monitoring.
To have the option of changing settings in addition to monitoring, a DTU Pro is required instead of the DTU Lite.
How it works
The Hoymiles microinverter converts the solar power generated by your photovoltaic system, AC grid compliant and feeds it directly into the utility grid. Each Hoymiles microinverter is individually connected to a PV module of your system for this purpose. This unique configuration means that each PV module is controlled by an individual maximum peak power point tracker (mppt). This ensures that the maximum available power from each individual module is fed into the utility grid, regardless of the output of the other PV modules in the system. Thus, if individual PV modules in the system are affected by shading, soiling, orientation, or mismatch, the hm-350 still ensures peak power for its associated PV module. The result is the maximum possible energy production from your PV system.
Optimal reliability
Microinverter systems are inherently more reliable than conventional inverters. The decentralized design of a microinverter system ensures that the entire PV system will not fail in the event of a malfunction. Hoymiles microinverters are designed to operate at full power in ambient temperatures up to +65°C (150°F). The microinverter enclosure is designed for outdoor installation and is IP67 rated.
Simple design
PV systems with Hoymiles microinverters are very easy to design and install. You can install a combination of PV modules of different types, in any orientation and in a desired number (Maximum number of devices in series: 14). You do not need to install cumbersome conventional inverters. Each microinverter can be quickly mounted on the PV mounting rack or directly under the PV module. The PV module is connected to the microinverter directly on site, eliminating the risk of exposing people to dangerously high DC voltage.
Technical data
Recommended module power: up to 440W
Peak power mppt of voltage range: 33~48V
Starting voltage: 22V
Battery voltage range: 16~60V
Maximum input voltage: 60V
Maximum input current: 11.5A
Maximum input short circuit current: 15A
Rated output power: 350VA
Rated output voltage: 1.52a at 230V
Rated output current: 230V
CEC weighted efficiency: 96.50%
Ambient temperature range: -40~+65°C
Dimensions (WxHxD): 182 x 164 x 29mm
Weight: 1.98kg (including 1.35m AC cable)
Enclosure rating: IP67
Scope of delivery
Hoymiles hm-350 micro inverter
€261.68*
€219.90**
The hm-350 from Hoymiles is the perfect micro inverter for your balcony power plant. The compact lightweight (only 1.98kg including the 1.35m AC cable...
The Hoymiles hms Field-Connector is an essential part of the Hoymiles hms PlugandPlay cable system, specifically designed for PV systems with a single microinverter.The Field-Connector connects directly to the inverter and provides an easy connection option to an AC cable. This straightforward plug-and-play design allows users to quickly and easily connect the single inverter system to the power grid.Connection to the power grid must only be done by an electrician.Hoymiles hms cable systemThe hms cable system is an innovative solution for wiring hms inverters in PV systems. It offers a user-friendly plug-and-play design that allows for easier, faster and more reliable installation. The flexible hms cable system allows users to combine cables of different sizes or lengths to cost-effectively implement the desired cabling configuration.ExamplesIn a system with one hms inverter:1x hms Connection cable PlugandPlay with field connector and Schuko plugor1x hms Field connector for own assembly of a cableFor a system with e.g. 2 hms inverters:1x hms Sealing Cap1x hms Connection Cable2x hms Trunk ConnectorOptional: - hms Extension Connector for extension of the cable - hms Disconnect Tool for disassembling the connectorTechnical DataRated voltage: 300VRated current: 12APower frequency and dielectric strength: 3000VACTemperature range: -40 to 85°CDimensions: 135 x 38 x 25mmProtection class: IP68for cables with outer diameter 8 - 9,5mmApplicable cables: 16/18 awg, 1.0/1.5mm² copper cableScope of delivery:1x Hoymiles hms Field Connector
€10.59*
€8.90**
The Hoymiles hms Field-Connector is an essential part of the Hoymiles hms PlugandPlay cable system, specifically designed for PV systems with a single...
Lapp solar xlr-r cables are weather-, abrasion- and uv-resistant photovoltaic cables. These halogen-free, double-insulated and cross-linked solar cables are suitable for permanent outdoor use to connect grounded and ungrounded photovoltaic systems. They are used both for wiring solar modules to each other and for connecting the individual module rows and the inverter. The cable has been tested by TÜv Rheinland according to 2 PfG 1169/08.2007 (pv1-f) design.
Important product features:
Cable cross-section: 1x4mm
Manufacturer: Lapp Kabel
Color outer insulation: Black
Color inner insulation: White
xlr-r solar cables from Lapp can generally be laid in protective tubes suitable for buried installation in the ground if it is ensured that there is no permanent contact with water and that waterlogging is safely drained away. The laying of the cables in the ground as well as the correct design of the cable trench must comply with vde 0100 part 520 or comparable standards in order to prevent damage to the protective conduit and permanent exposure of the cables and conduits to penetrating water. Long-term, permanent storage as well as permanent operation of the cables in or under water is not permitted.
Conductor construction
1. Conductor: Fine stranded wire of tinned cu-wires, according to iec 60228, class 5
2. Core insulation: electron beam crosslinked polyolefin co-polymer
3. Outer sheath Electron beam crosslinked polyolefin co-polymer Outer sheath color: black or black with red or blue stripe
Electrical properties
Rated voltage: u0 /u according to iec ac 600/1000 v dc 900/1500 v
Max. permissible system voltage: 1.8 kv dc (conductor/conductor, not grounded system) according to TÜv 2 PfG 1169/08.2007 Test voltage ac 6.5 kv
Thermal characteristics
Temperature range fixed: -40° c to +120° c max. conductor temperature (according to en 60216-2)
Temperature range according to fixed installation: -40 °c to +90 °c ambient temperature TÜv 2 PfG 1169/08.2007
installation temperature flexible: max. -25 °c
Thermal pressure resistance according to en 60811-3-1
Humidity-heat test according to en 60068-2-78 at 85% humidity
mechanical properties
Minimum bending radius occasionally moved: 15 x cable diameter
permanently installed: 5 x cable diameter
Dynamic penetration according to dke requirement profile Pv1-F ak 411.2.3 appendix F
Tear resistance according to dke requirement profile Pv1-F ak 411.2.3 Annex G
Testing of tensile strength and elongation according to en 60811
chemical properties
Weathering / Uv resistance according to hd 605/A1
Ozone resistance according to en 50396
Halogen free according to en 50267
Fire resistance flame retardant according to iec 60332-1-2
Acid and alkali resistance according to en 60811-2-1 (oxalic acid and caustic soda)
€1.50*
€1.26**
Lapp solar xlr-r cables are weather-, abrasion- and uv-resistant photovoltaic cables. These halogen-free, double-insulated and cross-linked solar cabl...
Lapp SOLAR XLS-R T 2x4mm is a radiation cross-linked high-end solar cable made in Germany with optimised cable design, the solar cable is slim, light and robust and saves a lot of time during installation.
The twin cable can be easily separated into two cables if necessary. You do not need any special tools for this. Nevertheless, the connection of the two wires is extremely stable if you prefer to leave the cable together.
This article is sold by the metre. Each item corresponds to one metre. If you buy e.g. 10x this article, you will receive a coherent piece with 10m length.
Product features
Weather/UV resistant according to HD 605/A1
Ozone resistant according to EN 50396
Halogen free and flame retardant
Good notch and abrasion resistance
XLS-R T= X-Linked Standard-Reduced Twin
Proven electron beam crosslinked quality
Standard references / approvals
Also available as TÜV PV1-F certified version on request - Ideal for stand-alone PV systems
Areas of application
Ideal for stand-alone PV systems
Gable and flat roof photovoltaic systems
Photovoltaic or solar field systems
Flexible or building-integrated PV systems
Benefit
Easy to separate into two individual lines
Reduced outer diameters allow space- and weight-saving installation
Robust against mechanical impact
Reduction of fire spread and toxic smoke formation in case of fire
Exact quantity control during installation due to metre marking on the cable jacket
Structure
Fine stranded, tinned copper conductor
Core insulation of irradiated copolymer
Outer sheath of irradiated copolymer
Outer sheath colour: Black
Cores connected in parallel with separator
Technical data
Core ID code: black / red - blue / red
Classification: ETIM 5.0 Class-ID: EC001578 ETIM 5.0
Class-Description: Flexible cable
Conductor construction: Fine-stranded according to VDE 0295, Class 5 / IEC 60228 Cl.5
Minimum bending radius: Fixed installation: 4 x outer diameter
Rated voltage: AC U0/U : 600/1000 V DC U0/U : 900/1500 V
Max. permissible system voltage: DC 1.8 kV (conductor-conductor, not earthed system)
Test voltage: AC 6500 V
Temperature range: -40°C to +100°C max. conductor temperature
Lapp SOLAR XLS-R T 2x4mm is a radiation cross-linked high-end solar cable made in Germany with optimised cable design, the solar cable is slim, light and robust and saves a lot of time during installation.
The twin cable can be easily separated into two cables if necessary. You do not need any special tools for this. Nevertheless, the connection of the two wires is extremely stable if you prefer to leave the cable together.
€2.78*
€2.34**
Lapp SOLAR XLS-R T 2x4mm is a radiation cross-linked high-end solar cable made in Germany with optimised cable design, the solar cable is slim, l...