Victron Energy Inverter 12/500 230V VE.Direct Schuko
€143.63*
€120.70**
The Victron Energy Inverter 12/500 230V VE.Direct SCHUKO (MPN: PIN121501210) converts the DC voltage from a 12-V battery system into 230-V AC voltage and supplies it via a Schuko outlet. The inverter delivers 450 W of continuous power at 25 °C, up to 500 W for one hour, and 750 W of peak power for brief periods of increased load. This makes it suitable for powering compatible 230-V loads in mobile and stationary battery systems. The VE.Direct interface allows you to monitor operating data and adjust key settings. ECO mode reduces self-consumption to as low as 1 W when the load is low or absent.
Victron 12/500 Inverter with VE.Direct and Schuko Output
- 450 W continuous power at 25 °C and 380 W at 40 °C
- 500 W for up to one hour
- 750 W peak power for short-term increased power demand
- 230 V Schuko output for compatible AC loads
- VE.Direct interface for monitoring and configuration
- ECO mode with only 1 W no-load power
- Configurable shutdown and restart thresholds for battery protection
- Connection for remote on/off control
- Comprehensive protection functions against overload, short circuit, and overtemperature
Reliable power supply for 230-V loads
With 450 W of continuous power at 25 °C, the inverter supplies suitable 230 V devices from a 12 V battery system. For short-term loads, up to 500 W is available for one hour. The peak power of 750 W supports loads with a brief spike in power demand during startup. The output frequency can be set between 50 and 60 Hz. An automatic AC transfer switch is not integrated.
Monitoring and Configuration via VE.Direct
The VE.Direct interface enables monitoring of battery voltage, output voltage, load, as well as warnings and alarms. Important operating parameters can be configured via VictronConnect. This requires a separately available VE.Direct-to-USB interface or a VE.Direct Bluetooth Smart dongle, as Bluetooth is not built-in. Compatible GX devices or a GlobalLink 520 can also be integrated using an additional VE.Direct cable.
ECO Mode and Configurable Battery Protection
In ECO mode, the inverter switches to an energy-saving search mode when the load is low or absent, reducing the no-load power to 1 W. As soon as a sufficiently large load is detected, it resumes normal operation. The startup power, search interval, and search time can be adjusted. Additionally, adjustable undervoltage thresholds and a dynamic, load-dependent shutdown protect the connected battery system.
Installation and Integrated Protection Functions
The inverter is designed for dry, well-ventilated installation areas. To ensure adequate cooling, maintain approximately 10 cm of clearance around the unit. Integrated protection functions monitor, among other things, output short circuits, overloads, battery overvoltage and undervoltage, overtemperature, and excessive DC ripple voltage. Installation, grounding, and electrical configuration must be performed by a qualified electrician. The Schuko outlet must not be connected to an external AC power source.
Technical Specifications
Inverter and AC Output
- Battery system voltage: 12 V DC
- DC input voltage range: 9.2–17 V
- Continuous power at 25 °C: 450 W
- Continuous power at 40 °C: 380 W
- Short-term power during cold start: 500 W for 1 hour
- Peak power: 750 W
- Output voltage: 230 V AC ± 3%
- Output frequency: 50 or 60 Hz ± 0.1%, adjustable
- Maximum efficiency: 86%
- No-load power: 7 W
- No-load power in ECO mode: 1 W
- AC output: Schuko CEE 7/4
Battery protection and DC connection
- Undervoltage shutdown, default value: 9.3 V
- Restart and alarm threshold, default value: 10.9 V
- Charged battery detection, default value: 14.0 V
- Battery connection: Screw terminals
- Maximum battery cable cross-sectional area: 10 mm²
- Recommended cable cross-sectional area up to 1.5 m: 6 mm²
- Recommended cable cross-section for 1.5–3 m: 10 mm²
- Internal DC fuse: 3 × 35 A, 32 V, ATOF, non-replaceable
- Protection functions: Short circuit, overload, battery overvoltage and undervoltage, overtemperature, AC voltage present at the output, and excessive DC ripple voltage
Communication and System Integration
- Communication interface: VE.Direct
- Bluetooth: not integrated; optional dongle required
- Remote On/Off connection: available
- Automatic AC transfer switch: not built-in
- Hardware generation: HW15
General Technical Specifications
- Manufacturer part number: PIN121501210
- Operating temperature: −40 to +65 °C
- Power derating: 1.25% per °C above 40 °C
- Relative humidity: maximum 95%, non-condensing
- Protection rating: IP21 for base mounting, IP20 for approved wall mounting
- Protection class: I
- Housing: Steel with plastic cover
- Color: Blue, RAL 5012
- Dimensions: 86 × 172 × 275 mm
- Weight: 3.5 kg
- Safety standards: EN/IEC 60335-1 and EN/IEC 62109-1
- EMC standards: EN 55014-1, EN 55014-2, IEC 61000-6-1, IEC 61000-6-2, and IEC 61000-6-3
Package contents:
1x Victron Energy Inverter 12/500 230V VE.Direct SCHUKO
Manufactuerer Information
Victron Energy
Victron Energy B.V.
De Paal 35
1351 JG Almere
Netherlands
Mail: sales@victronenergy.com
Tel.: +31 365359700