The vcc 1212-50 from Votronic (3326) is a fully automatic, uninsulated, battery charge converter for special vehicles, high-end motorhomes, boat. The charge converter (booster) of the series "vcc" has been developed according to the latest specifications for mobile charging of supply batteries (living space / on-board batteries), from the alternator (starter battery) while driving. The device provides a complete IU1oU2 charging characteristic even while driving. The max charge current of the vcc 1212-50 is 50a and it can work with lead acid, gel, agm1, agm2 and LiFePO4 batteries. This device charges a 12v battery from a 12v battery / alternator. Unlike the conventional disconnect relay, the charging voltage is lowered or raised according to the charging program default, so it is especially good for EURO standard 6, 6 + plus vehicles. Universally applicable multi-talent For on-board batteries in classic lead-acid, lead-gel or lead-AGM as well as modern lithium-LiFePO4 technology, the 8 selectable charging programs ensure a monitoring-free, rapid and gentle full charge from any state of charge with subsequent full maintenance and care of the battery. Even during short journeys, the battery is charged with full charging current. Connected 12 V consumers are automatically supplied as well, even if the on-board network is heavily loaded. The automatic power control ensures the necessary safety and startability of the vehicle important features of the Votronic 3326 vcc 1212-50 The vcc 1212-50 is a b2b charger without galvanic isolation for charging 12v batteries from a 12v alternator / battery. max charging current: 50a, input voltage range 12v, charges 12v batteries, recommended battery capacity: 75 - 440Ah Increases or decreases the voltage to the necessary level to accurately charge the on-board battery with the optimal charging characteristic for it. It fully compensates for line losses and alternator voltage fluctuations, such as those that occur constantly to a significant extent in Euro 6 vehicles (intelligent alternators). Features compact design, light weight (high frequency switch mode technology) and power components with strong dimensions for safe operation. Significantly improved energy balance of the on-board battery. No intervention in the starter circuit; the unit behaves like a powerful consumer on the alternator. The supplied 12 V consumers are protected against overvoltage and voltage fluctuations. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Fully automatic operation: the device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. When the engine is not running, the batteries are not discharged. Parallel and buffer operation: in case of simultaneous consumption, the battery continues to be charged or kept full. The device automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery back discharge by electronic cut-off up to complete disconnection of device and battery. Built-in on-board power supply filter: Problem-free parallel operation with other charging sources (ebl, chargers, motor and fuel generators, Solaranlagen) on one battery. Charging cable compensation: Voltage losses on the charging cables are automatically compensated. Connection for battery temperature sensor (sensor included in scope of delivery). For lead batteries (acid, gel, agm), the charging voltage is automatically adjusted to the battery temperature. This causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided. LiFePO4 batteries: Battery protection at high and especially adapted charging at low temperatures below 0 °c. Charging aid for deeply discharged lead batteries: Gentle pre-charge of the (lead-acid, -gel, agm) battery up to 8 v, then powerful support of the battery with any consumers still switched on. ?Also ensures the automatic activation of a LiFePO4 battery disconnected by the bms. What added value does the use of a b2b charge converter offer me? The charge converters ensure optimal and fast charging of the supply battery from the alternator while driving. In contrast to the simple cut-off relay, the charging voltage is raised to the value that is necessary for the respective battery type for a full charge and is required by the battery manufacturers. This means that the full charging current can flow and already charge considerable amounts of current into the battery in a short time. Long charging lines and losses are neatly compensated for, as are voltage fluctuations at the alternator. In the case of charge converters with different input and output voltages (12v/24V or 24V/12v), the simple charging of a second battery is also possible without installing a second alternator The charge converters thus provide the well-known high quality of battery charging of the votronic chargers even while driving. The intelligent microprocessor charge control with "IU1oU2oU3" charge characteristics and dynamic charge time calculation automatically ensures the fast and gentle full charge as well as subsequent charge retention of the connected batteries from any state of charge and always allows the simultaneous co-supply of consumers in parallel to the supply battery Scope of delivery: 1X Votronic 3326 vcc 1212-50 50a charging converter 1x user manual (German) 1x temperature sensor

The Orion Tr-Smart dc-dc from Victron Energy (mpn ori242440140) is a professional, dc to dc adaptive 3-stage charger with integrated Bluetooth, known in the market as a battery-to-battery (b2b) charger. The charge booster is suitable for use in dual battery systems in vehicles or boats where the alternator and starting battery are used to charge the service battery. The charger can be used in 12v or 24V systems and is suitable for both lead acid and lithium batteries. Models up to 400w are available and an unlimited number of units can be connected in parallel to increase the output power. Main features Suitable for Bluetooth Smart Fully programmable Adaptive 3-step charging algorithm Remote on/off Short circuit proof Parallel connection possible to increase output current overtemperature protection Protection class IP43 Suitable for Bluetooth Smart Monitoring, changing settings and updating the charger when new software functions become available can be done with any Bluetooth enabled smartphone, tablet or other device. Adaptive 3-stage charging algorithm: constant current - constant voltage - conservation For lead acid batteries, it is important to keep the recording time short during shallow discharges to avoid overcharging the battery. After a deep discharge, the constant voltage duration is automatically extended to ensure that the battery charges fully. For lithium batteries, the recording time is fixed, by default 2 hours. Alternatively, a fixed output voltage can be selected. Remote on/off A remote on/off switch or relay contact can be connected to the two-pin connector. Alternatively, the h terminal (right) of the two-pin plug can be connected to a battery positive terminal or the l terminal (left) of the two-pin plug can be connected to the battery negative terminal (or to the body of a vehicle, for example). Technical data Input voltage range: 20-35 V Rated output voltage: 24.2 V Output voltage setting range: 20-30 V Output voltage tolerance: ±0.2 V Cont. Output current at nominal output voltage and 40°: 17 A Cont. Output power at 40°C: 400 W Operating temperature range: -20°C - +55°C Weight: 1,6 kg Dimensions: 130 x 186 x 70 mm scope of delivery: 1x Victron Energy Orion-Tr Smart dc/dc charge booster 24/24-17a (400w) ORI242440140

The Blue Smart ip22 12/30(1) charger from Victron Energy (mpn bpc123042002), is a professional, compact 12v 30a battery charger of the latest generation with a charging output and built-in Bluetooth! The Blue Smart ip22 12/30(1) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 12v lead batteries and modern lithium batteries. It offers Highlights of the 12/30(1) Blue Smart ip22 Charger intelligent charging, until the perfect battery condition.... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 12/30(1) charger has built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the main technical features of the 12/30(1) Blue Smart ip22 Charger Victron Part number: bpc123042002 charges 12v lead acid, gel, agm and lithium batteries 30a maximum charge current 1 battery charge output very compact dimensions: 235 x 108 x 65mm highly advanced seven-step charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 12/30(1) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 12/30(1) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 12v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc123042002 12/30(1) ip22 Blue Smart Charger 1x instruction manual

The Orion-Tr Smart 12/12-18a from victron Energy (mpn ori121222120) is a galvanically isolated dc-dc converter and charger. It is suitable for use in dual battery systems in vehicles or boats where the (smart) alternator and starter battery are to be used to charge the service battery. The charger can be used in 12v or 24v systems and is suitable for both lead-acid and lithium batteries. An unlimited number of units can be connected in parallel to increase the output power. Thanks to the Orion-Tr Smart 12/12-18a you can supply any 12v consumer with exactly the right voltage. The correct voltage is guaranteed even with longer lines, because the Orion can adjust the voltage to any line losses that occur. For many sensitive electronic devices, maintaining the exact operating voltage is essential for smooth operation. Integrated Bluetooth, fully programmable monitoring, changing settings and updating the charger when new software features become available can be done with any Bluetooth-enabled smartphone, tablet or other device. The Orion-Tr Smart can be programmed with a configurable battery charging algorithm or a fixed output. It also features smart generator compatibility - engine run detection. Features of the Orion-Tr Smart 12/12-18a 220w (galvanically isolated) victron Energy part number: ori121222120 for 12 v battery voltage, adjustable output voltage 10-15 v max. 220 w output power at a maximum current of 18 A wide input voltage range: 10 -17 v Protection class ip43, galvanic isolation 200 vDC between input, output and housing can be connected in parallel with any number of identical devices to increase output power can be used for buffer charging of batteries remote on/off switch intelligent generator compatibility: engine run detection Adaptive 3-stage charging algorithm: constant current - constant voltage - conservation For lead-acid batteries, it is important to keep the recording time short during shallow discharges to avoid overcharging the battery. After a deep discharge, the constant voltage duration is automatically extended to ensure that the battery charges fully. For lithium batteries, the recording time is fixed, by default 2 hours. Alternatively, a fixed output voltage can be selected. Remote on/off switch A remote on/off switch or a relay contact can be connected to the two-pin connector. Alternatively, the h terminal (right) of the two-pin plug can be connected to a battery positive terminal or the l terminal (left) of the two-pin plug can be connected to the battery negative terminal (or to the body of a vehicle, for example). scope of delivery: 1x victron Energy ori121222120 Orion-Tr Smart 12/12-18a 220 w dc-dc converter 1x instruction manual

The vcc 1212-70 from Votronic (3328) is a fully automatic, non-isolated, battery charge converter for special vehicles, high-end motorhomes, boat. The charge converter (booster) of the series "vcc" is designed according to the latest specifications for mobile charging of supply batteries (living space / on-board batteries), from the alternator (starter battery) while driving. The device provides a complete IU1oU2 charging characteristic even while driving. The max charge current of the vcc 1212-70 is 70a and it can work with lead acid, gel, agm1, agm2 and LiFePO4 batteries. This device charges a 12v battery from a 12v battery / alternator. Unlike the conventional disconnect relay, the charging voltage is lowered or raised according to the charging program default, so it is especially good for EURO standard 6, 6 + plus vehicles. Universally applicable multi-talent For on-board batteries in classic lead-acid, lead-gel or lead-AGM as well as modern lithium-LiFePO4 technology, the 8 selectable charging programs ensure a monitoring-free, rapid and gentle full charge from any state of charge with subsequent full maintenance and care of the battery. Even during short journeys, the battery is charged with full charging current. Connected 12 V consumers are automatically supplied as well, even if the on-board network is heavily loaded. The automatic power control ensures the necessary safety and startability of the vehicle important features of the Votronic 3328 vcc 1212-70 The vcc 1212-70 is a b2b charger without galvanic isolation for charging 12v batteries from a 12v alternator / battery. max charge current: 70a, input voltage range 12v, charges 12v batteries, recommended battery capacity: 60 - 260Ah Increases or decreases the voltage to the necessary level to accurately charge the on-board battery with the optimal charging characteristic for it. It fully compensates for line losses and alternator voltage fluctuations, such as those that occur constantly to a significant extent in Euro 6 vehicles (intelligent alternators). Features compact design, light weight (high frequency switch mode technology) and power components with strong dimensions for safe operation. Significantly improved energy balance of the on-board battery. No intervention in the starter circuit; the unit behaves like a powerful consumer on the alternator. The supplied 12 V consumers are protected against overvoltage and voltage fluctuations. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Fully automatic operation: the device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. When the engine is not running, the batteries are not discharged. Parallel and buffer operation: in case of simultaneous consumption, the battery continues to be charged or kept full. The device automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery back discharge by electronic cut-off up to complete disconnection of device and battery. Built-in on-board power supply filter: Problem-free parallel operation with other charging sources (ebl, chargers, motor and fuel generators, Solaranlagen) on one battery. Charging cable compensation: Voltage losses on the charging cables are automatically compensated. Connection for battery temperature sensor (sensor included in scope of delivery). For lead batteries (acid, gel, agm), the charging voltage is automatically adjusted to the battery temperature. This causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided. LiFePO4 batteries: Battery protection at high and especially adapted charging at low temperatures below 0 °c. Charging aid for deeply discharged lead batteries: Gentle pre-charge of the (lead-acid, -gel, agm) battery up to 8 v, then powerful support of the battery with any consumers still switched on. ?Also ensures the automatic activation of a LiFePO4 battery disconnected by the bms. What added value does the use of a b2b charge converter offer me? The charge converters ensure optimal and fast charging of the supply battery from the alternator while driving. In contrast to the simple cut-off relay, the charging voltage is raised to the value that is necessary for the respective battery type for a full charge and is required by the battery manufacturers. This means that the full charging current can flow and already charge considerable amounts of current into the battery in a short time. Long charging lines and losses are neatly compensated for, as are voltage fluctuations at the alternator. In the case of charge converters with different input and output voltages (12v/24V or 24V/12v), the simple charging of a second battery is also possible without installing a second alternator The charge converters thus provide the well-known high quality of battery charging of the votronic chargers even while driving. The intelligent microprocessor charge control with "IU1oU2oU3" charge characteristics and dynamic charge time calculation automatically ensures the fast and gentle full charge as well as subsequent charge retention of the connected batteries from any state of charge and always allows the simultaneous co-supply of consumers in parallel to the supply battery Scope of delivery: 1X Votronic 3328 vcc 1212-70 70a charging converter 1x user manual (German) 1x temperature sensor

The vcc 1212-90 from Votronic (3329) is a fully automatic, non-isolated, battery charge converter for special vehicles, high-end motorhomes, boat. The charge converter (booster) of the series "vcc" is designed according to the latest specifications for mobile charging of supply batteries (living space / on-board batteries), from the alternator (starter battery) while driving. The device provides a complete IU1oU2 charging characteristic even while driving. The max charge current of the vcc 1212-90 is 90a and it can work with lead acid, gel, agm1, agm2 and LiFePO4 batteries. This device charges a 12v battery from a 12v battery / alternator. Unlike the conventional disconnect relay, the charging voltage is lowered or raised according to the charging program default, so it is especially good for EURO standard 6, 6 + plus vehicles. Universally applicable multi-talent For on-board batteries in classic lead-acid, lead-gel or lead-AGM as well as modern lithium-LiFePO4 technology, the 8 selectable charging programs ensure a monitoring-free, rapid and gentle full charge from any state of charge with subsequent full maintenance and care of the battery. Even during short journeys, the battery is charged with full charging current. Connected 12 V consumers are automatically supplied as well, even if the on-board network is heavily loaded. The automatic power control ensures the necessary safety and startability of the vehicle important features of the Votronic 3329 vcc 1212-90 The vcc 1212-90 is a b2b charger without galvanic isolation for charging 12v batteries from a 12v alternator / battery. max charging current: 90a, input voltage range 12v, charges 12v batteries, recommended battery capacity: 150 - 800Ah Increases or decreases the voltage to the necessary level to accurately charge the on-board battery with the optimal charging characteristic for it. It fully compensates for line losses and alternator voltage fluctuations, such as those that occur constantly to a significant extent in Euro 6 vehicles (intelligent alternators). Features compact design, light weight (high frequency switch mode technology) and power components with strong dimensions for safe operation. Significantly improved energy balance of the on-board battery. No intervention in the starter circuit; the unit behaves like a powerful consumer on the alternator. The supplied 12 V consumers are protected against overvoltage and voltage fluctuations. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Fully automatic operation: the device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. When the engine is not running, the batteries are not discharged. Parallel and buffer operation: in case of simultaneous consumption, the battery continues to be charged or kept full. The device automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery back discharge by electronic cut-off up to complete disconnection of device and battery. Built-in on-board power supply filter: Problem-free parallel operation with other charging sources (ebl, chargers, motor and fuel generators, Solaranlagen) on one battery. Charging cable compensation: Voltage losses on the charging cables are automatically compensated. Connection for battery temperature sensor (sensor included in scope of delivery). For lead batteries (acid, gel, agm), the charging voltage is automatically adjusted to the battery temperature. This causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided. LiFePO4 batteries: Battery protection at high and especially adapted charging at low temperatures below 0 °c. Charging aid for deeply discharged lead batteries: Gentle pre-charge of the (lead-acid, -gel, agm) battery up to 8 v, then powerful support of the battery with any consumers still switched on. ?Also ensures the automatic activation of a LiFePO4 battery disconnected by the bms. What added value does the use of a b2b charge converter offer me? The charge converters ensure optimal and fast charging of the supply battery from the alternator while driving. In contrast to the simple cut-off relay, the charging voltage is raised to the value that is necessary for the respective battery type for a full charge and is required by the battery manufacturers. This means that the full charging current can flow and already charge considerable amounts of current into the battery in a short time. Long charging lines and losses are neatly compensated for, as are voltage fluctuations at the alternator. In the case of charge converters with different input and output voltages (12v/24V or 24V/12v), the simple charging of a second battery is also possible without installing a second alternator The charge converters thus provide the well-known high quality of battery charging of the votronic chargers even while driving. The intelligent microprocessor charge control with "IU1oU2oU3" charge characteristics and dynamic charge time calculation automatically ensures the fast and gentle full charge as well as subsequent charge retention of the connected batteries from any state of charge and always allows the simultaneous co-supply of consumers in parallel to the supply battery Scope of delivery: 1X Votronic 3329 vcc 1212-90 90a charging converter 1x user manual (German) 1x temperature sensor

The vcc 1212-45 IUoU-Li from Votronic (3308) is a fully automatic, galvanically isolated battery charging converter for special vehicles, high-end motorhomes, boats with galvanic isolation. The charge converter (booster) of the series "vcc" has been developed according to the latest specifications for mobile charging of supply batteries (living space/onboard batteries), from the alternator (starter battery) while driving. The device provides a complete IU1oU2 charging characteristic even while driving. The max charge current of the vcc 1212-45 is 45a and it can work with lead-acid, gel, agm1, agm2 and LiFePO4 batteries. Unlike the conventional isolating relay, the charging voltage is lowered or raised according to charging program specification, so it is especially good for EURO standard 6, 6 + plus vehicles. Universally applicable multi-talent For on-board batteries in classic lead-acid, lead-gel or lead-AGM as well as modern lithium-LiFePO4 technology, the 8 selectable charging programs ensure a monitoring-free, rapid and gentle full charge from any state of charge with subsequent full maintenance and care of the battery. Even during short journeys, the battery is charged with full charging current. Connected 12 V consumers are automatically supplied as well, even if the on-board network is heavily loaded. The automatic power control ensures the necessary safety and startability of the vehicle important features of the Votronic 3308 vcc1212-45 IUoU-Li The vcc 1212-45 is b2b charger with galvanic isolation for charging 12v batteries from a 12v alternator / battery. max. charging current: 45a, input voltage range 12v, charges 12v batteries, recommended battery capacity: 90 - 400 Ah Increases or decreases the voltage to the necessary level to accurately charge the on-board battery with the optimal charging characteristic for it It fully compensates for line losses and alternator voltage fluctuations, such as those that occur constantly to a significant extent in Euro 6 vehicles (intelligent alternators) Features compact design, light weight (high frequency switch mode technology) and power components with strong dimensions for safe operation Significantly improved energy balance of the on-board battery. No intervention in the starter circuit; the unit behaves like a powerful consumer on the alternator The supplied 12 V consumers are protected against overvoltage and voltage fluctuations The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Fully automatic operation: the device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. When the engine is not running, the batteries are not discharged. Parallel and buffer operation: in case of simultaneous consumption, the battery continues to be charged or kept full. The device automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery back discharge by electronic cut-off up to complete disconnection of device and battery. Built-in on-board power supply filter: Problem-free parallel operation with other charging sources (ebl, chargers, motor and fuel generators, Solaranlagen) on one battery Charging cable compensation: Voltage losses on the charging cables are automatically compensated Connection for battery temperature sensor (sensor included in scope of delivery). For lead batteries (acid, gel, agm), the charging voltage is automatically adjusted to the battery temperature. This causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided LiFePO4 batteries: Battery protection at high and especially adapted charging at low temperatures below 0 °c. Charging aid for deeply discharged lead batteries: Gentle pre-charge of the (lead-acid, -gel, agm) battery up to 8 v, then powerful support of the battery with any consumers still switched on ?Also ensures the automatic activation of a LiFePO4 battery disconnected by the bms What added value does the use of a b2b charge converter offer me? The charge converters ensure optimal and fast charging of the supply battery from the alternator while driving. In contrast to the simple cut-off relay, the charging voltage is raised to the value that is necessary for the respective battery type for a full charge and is required by the battery manufacturers. This means that the full charging current can flow and already charge considerable amounts of current into the battery in a short time. Long charging lines and losses are neatly compensated for, as are voltage fluctuations at the alternator. In the case of charge converters with different input and output voltages (12v/24V or 24V/12v), the simple charging of a second battery is also possible without installing a second alternator The charge converters thus provide the well-known high quality of battery charging of the votronic chargers even while driving. The intelligent microprocessor charge control with "IU1oU2oU3" charge characteristics and dynamic charge time calculation automatically ensures the fast and gentle full charge as well as subsequent charge retention of the connected batteries from any state of charge and always allows the simultaneous co-supply of consumers in parallel to the supply battery Scope of delivery: 1X Votronic 3308 vcc 1212-45 IUoU-Li 45s 12v charging converter 1x user manual (German) 1x temperature sensor

The Orion-Tr Smart 12/12-30a from Victron Energy (mpn ori121236120) is a galvanically isolated dc-dc converter charger. It is suitable for use in dual battery systems in vehicles or boats where the (smart) alternator and starter battery are to be used to charge the service battery. The charger can be used in 12v or 24V systems and is suitable for both lead acid and lithium batteries. An unlimited number of units can be connected in parallel to increase the output power. Thanks to the Orion-Tr Smart 12/12-30a you can supply any 12v consumer with exactly the right voltage. The correct voltage is guaranteed even with longer lines, because the Orion can adjust the voltage to any line losses that occur. For many sensitive electronic devices, maintaining the exact operating voltage is essential for smooth operation. Integrated Bluetooth, fully programmable monitoring, changing settings and updating the charger as new software features become available can be done with any Bluetooth-enabled smartphone, tablet or other device. The Orion-Tr Smart can be programmed with a configurable battery charging algorithm or a fixed output. It also features smart generator compatibility - engine run detection. Features of the Orion-Tr Smart 12/12-30a 360w (galvanically isolated) Victron Energy part number: ori121236120 for 12v battery voltage, adjustable output voltage 10-15V max. 360w output power at a maximum current of 30A wide input voltage range: 10 -17V Protection class ip43, galvanic isolation 200v dc between input, output and housing can be connected in parallel with any number of identical devices to increase output power can be used for buffer charging of batteries remote on/off switch intelligent generator compatibility: engine run detection Adaptive 3-step charging algorithm: constant current -constant voltage -maintenance For lead-acid batteries, it is important to keep the recording time short during shallow discharges to avoid overcharging the battery. After a deep discharge, the constant voltage duration is automatically extended to ensure that the battery charges fully. For lithium batteries, the recording time is fixed, by default 2 hours. Alternatively, a fixed output voltage can be selected. Remote on/off switch A remote on/off switch or a relay contact can be connected to the two-pin connector. Alternatively, the h terminal (right) of the two-pin plug can be connected to a battery positive terminal or the l terminal (left) of the two-pin plug can be connected to the battery negative terminal (or to the body of a vehicle, for example). scope of delivery: 1x Victron Energy ori121236120 Orion-Tr Smart 12/12-30a 360 w dc-dc converter 1x instruction manual

The Blue Smart ip22 12/15(1) charger from Victron Energy (mpn bpc121542002), is a professional, compact 12v 15a battery charger of the latest generation with a charging output and built-in Bluetooth! The Blue Smart ip22 12/15(1) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 12v lead batteries and modern lithium batteries. It offers Highlights of the 12/15(1) Blue Smart ip22 Charger intelligent charging, until the perfect battery state... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 12/15(1) charger has built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the main technical features of the 12/15(1) Blue Smart ip22 Charger Victron Part number: bpc121542002 charges 12v lead acid, gel, agm and lithium batteries 15a maximum charge current 1 battery charging output very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 12/15(1) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 12/15(1) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 12v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc121542002 12/15(1) ip22 Blue Smart Charger 1x instruction manual

The Battery Charger VBCS Triple is a brand new type of device combination to ensure the energy supply in your caravan. It consists of a pb-grid-charger, VCC charging converter and MPP solar charge controller. The batteries are always charged automatically no matter if driving or parking. Especially the high charging performance (45A) of the integrated charging converter allows full charging of your batteries even on short drives. The VBCS Triple series provides the same quality, features and functions as the Votronic single devices and comes with a very compact and light design. These devices save costs and space within your caravan - installation, connection and wiring are reduced to a minimum. Important product features: integrated VCC charging converter 45A integrated Pb-grid- charger 30A integrated MPP solar charge controller for a max. module performance of 350W charges 1 supply battery, 1 starter battery or 2 supply batteries or 2 starter batteries constant full-automated charging very secure operation, soft battery charging 8 charging curves for acid, gel, AGM and modern LiFePO4 batteries control input for LiFePO4 - BMS for charging stop the charging voltages are free from spikes and controlled in a way to prevent from overloads precise battery temperature compensation, temperature sensor 825 included smart micro processor controlling considers connected consumers automatical battery recharge during longer standing times (twice a week) integrated battery pulser compensation of voltage loss (cables) for exact charging voltage reliable technique and compact design easy setup and short cabling plug&play connection for LCD-Charge Control S Suitable for all common battery sizes three different device combinations are available. All devices provide 8 charging curves for lead-acid, gel and AGM batteries as well as lithium-LiFePO4. The integrated battery trainer keeps the batteries maintained during longer standing times. LCD Charge Computer 1247 (optional)Especially designed for this device the LCD display and control unit shows important information. Additionally the charger can be adjusted to the power supply of the caravans pitch. Technical Data: Integrated MPP dual charge controller module performance: 50 - 350Wp Module amp max.: 21.0A Module voltage (Voc) max.: 28V Charging amp supply-/starter battery max.: 25.5/5.0A Integrated charger: operating voltage: 110 - 230V AC 45.65Hz (worldwide) Max. power consumption: 520W Charging amp supply-/starter battery max.: 30/5A Integrated 12V712V battery to battery VCC charging converter charging performance on-board battery max.: 45A automatic activation D+ / ignition starter battery LiMa voltage range (Euro6) / max. current: 11 - 16V/42A

The Blue Smart ip65 12/4 12v 230v battery charger (bpc120431064r) is the latest professional, charger from victron Energy with built-in Bluetooth. It is designed to charge 12v batteries of various types and delivered a maximum charging current of 4a. Together with the free victronConnect App you can easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain degree.technical highlights of the Blue Smart ip65 12/5 battery charger easy configuration and setup of the Blue Smart ip65 12/4 via Bluetooth interface suitable for all 12v battery types max. 4a charging current solid protection against splash water. Dust and chemicals thanks to ip65 protection has several functions to extend battery life automatic temperature adjustment at low or high temperatures automatic power supply function 7-step intelligent charging algorithm can recover fully discharged batteries "dead batteries has low energy mode for charging small batteries victron-Part number: bpc120431064r Lithium-ion battery mode ultra-high efficiency "green" battery charger With up to 95% efficiency, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, power consumption is reduced to 0.5 watts, five to ten times better than the industry standard durable, safe and quiet low heat load on electronic components protected against dust, water and chemical ingress. Protection against overheating: the output current is linearly reduced when the temperature rises up to 60 °c, so the charger will not fail even at extreme temperatures the chargers are absolutely silent thanks to passive cooling: no fan or other moving parts Reconditioning (recovery) A lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulfation. Provided the process is stopped in time, it allows the sulfation to be partially reversed by charging the battery at low current until a higher voltage is reached Function to restore fully discharged batteries Most chargers with reverse polarity protection will not recognize a battery that has been discharged to zero volts or near zero volts and therefore will not recharge it. However, the Blue Power charger will attempt to recharge a fully discharged battery with low current and will resume normal charging after sufficient voltage has been established across the battery terminal optional accessories 12 v cigarette lighter plug with fuse 2 meter extension cable Terminals with fuses M6 cable lug connector with fuse Scope of delivery: 1x victron bpc120431064r Blue Smart ip65 12/4 12v 230v battery charger1x instruction manual1x connection terminals1x m8 cable lug connector

The Blue Smart ip 67 12/25 12v 230v battery charger from victron Energy (mpn BPC122547006) is a smart, high performance battery charger of the latest generation with 25a charging current for charging 12v agm, gel and lead acid batteries as well as lithium ion batteries. in terms of functionality, the Blue Smart ip67 series is identical to the chargers of the Blue Smart ip 65 and ip 22 device families except for a few functions. Only the operating environment for which these chargers are designed differs.The Blue Smart ip 67 battery chargers offer a wireless solution for monitoring voltage and current, adjusting settings and updating the charger when new features become available, thanks to integrated Bluetooth.important features of the Blue Smart ip67 12/25 25a battery charger victron Part number: bpc122513006 Model name: Blue Smart ip 67 12/25 max. charging current: 25a for battery voltage: 12v dc for mains voltage: 180-265 vac 45-65 Hz fully enclosed: waterproof, shockproof and fire retardant smart configuration and monitoring via integrated bluetooth and free app adaptive 5-step charging algorithm prolongs the life of your batteries thanks to integrated storage mode can be used to power 12v consumers high quality cast aluminum housing Protection against application errors: reverse polarity on battery (fuse), protection against overtemperature, protection against output short circuit fully encased: waterproof, shockproof and fire retardantWater, oil or dirt cannot damage the Blue Smart ip67 charger. The case is made of cast aluminum and the electronics are coated with resin.one of the highest charging efficiencies ever!Setting a new industry standard: With an efficiency of 92% or more, these chargers produce three to four times less heat.adaptive 5-stage charging algorithmThe Blue Smart 12/25 ip67 charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. "Bulk" (constant current phase) "Absorption" (constant voltage phase) "Recondition" (regeneration phase) "Float" (charge maintenance voltage phase) "Storage" (storage mode) Storage mode: less maintenance and aging when the battery is at restStorage mode is activated whenever there has been no discharge within 24 hours. In storage mode, the charge maintenance voltage is then lowered to 2.2 v/cell (13.2 v for a 24 v battery) to minimize gas generation and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure main differences with the Blue Smart ip 65 familyThe two groups of devices differ in the following respects: the protection class, the ip 67 devices have the best possible protection Blue Smart ip 65 devices have a 7-stage charging algorithm, the ip67 has a 5-stage algorithm Scope of delivery:1x victron BPC122547006 Blue Smart ip67 12/25 25a 12v 230v battery charger1x instruction manual1x 1,5m battery connection cable red/black

The Blue Smart ip22 12/20(1) charger from Victron Energy (mpn bpc122042002), is a professional, compact 12v 20a battery charger of the latest generation with a charging output and built-in Bluetooth! The Blue Smart ip22 12/20(1) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 12v lead batteries and modern lithium batteries. It offers Highlights of the 12/20(1) Blue Smart ip22 Charger intelligent charging, until the perfect battery state... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 12/20(1) charger features built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the main technical features of the 12/20(1) Blue Smart ip22 Charger Victron Part number: bpc122042002 charges 12v lead-acid, gel, agm and lithium batteries 20a maximum charge current 1 battery charging output very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 12/20(1) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 12/20(1) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 12v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc122042002 12/20(1) ip22 Blue Smart Charger 1x instruction manual

The Blue Smart ip22 24/12(1) battery charger from Victron Energy (mpn bpc241242002), is a professional, compact 24v 12a battery charger of the latest generation with a charging output and built-in Bluetooth! The Blue Smart ip22 24/12(1) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 24v lead batteries and modern lithium batteries. It offers Highlights of the 24/12(1) Blue Smart ip22 Charger intelligent charging, until the perfect battery state... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 24/12(1) charger features built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the most important technical features of the 24/12(1) Blue Smart ip22 Charger Victron Part number: bpc241242002 charges 24v lead acid, gel, agm and lithium batteries 12a maximum charge current 1 battery charge output very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 24/12(1) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 24/12(1) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 24v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc241242002 24/12(1) ip22 Blue Smart Charger 1x instruction manual

The blue smart ip65 24/8 12v 230v battery charger (bpc240831064r) is the latest professional, charger from Victron Energy with built-in Bluetooth. It is designed to charge 24v batteries of various types and delivered a maximum charging current of 8a. Together with the free VictronConnect App you can easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain degree.technical highlights of the Blue Smart ip65 24/8 battery charger easy configuration and setup of the Blue Smart ip65 24/8 via Bluetooth interface suitable for all 24v battery types max. 8a charging current solid protection against splash water. Dust and chemicals thanks to ip65 protection has several functions to extend battery life automatic temperature adjustment at low or high temperatures automatic power supply function 7-step intelligent charging algorithm can recover completely discharged batteries "dead batteries has low energy mode for charging small batteries Victron-Part number: bpc240831064r Lithium-ion battery mode ultra-high efficiency "green" battery charger With up to 95% efficiency, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, power consumption is reduced to 0.5 watts, five to ten times better than the industry standard durable, safe and quiet low heat load on electronic components protected against dust, water and chemical ingress. Protection against overheating: the output current is linearly reduced when the temperature rises up to 60 °c, so the charger does not fail even at extreme temperatures the chargers are absolutely silent thanks to passive cooling: no fan or other moving parts Reconditioning (recovery) A lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulfation. Provided the process is stopped in time, it allows the sulfation to be partially reversed by charging the battery at low current until a higher voltage is reached Function to restore fully discharged batteries Most chargers with reverse battery protection will not recognize a battery that has been discharged to zero volts or near zero volts and therefore will not recharge it. However, the Blue Power charger will attempt to recharge a fully discharged battery with low current and will resume normal charging after sufficient voltage has been established across the battery terminals optional accessories Blue Smart ip 65 24/8 bpc240831064r 12 V cigarette lighter plug with fuse 2 meter extension cable Terminals with fuses M6 cable lug connector with fuse Scope of delivery: 1x Victron bpc240831064r Blue Smart ip65 24/8 230v battery charger1x instruction manual1x connection terminals1x m8 cable lug connector

The blue smart ip65 12/15 12v 230v battery charger (bpc121531064r) is the latest professional, charger from victron Energy with built-in Bluetooth. It is designed to charge 12v batteries of various types and provide a maximum charging current of 15a. Together with the free victronConnect App you can easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain degree.technical highlights of the Blue Smart ip65 12/15 battery charger easy configuration and setup of the Blue Smart ip65 12/15 via Bluetooth interface suitable for all 12v battery types max. 15a charging current solid protection against splash water. Dust and chemicals thanks to ip65 protection has several functions to extend battery life automatic temperature adjustment at low or high temperatures automatic power supply function 7-step intelligent charging algorithm can recover fully discharged batteries "dead batteries has low energy mode for charging small batteries victron-Part number: bpc121531064r Lithium-ion battery mode ultra-high efficiency "green" battery charger With up to 95% efficiency, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, power consumption is reduced to 0.5 watts, five to ten times better than the industry standard durable, safe and quiet low heat load on electronic components protected against dust, water and chemical ingress. Protection against overheating: the output current is linearly reduced when the temperature rises up to 60 °c, so the charger does not fail even at extreme temperatures the chargers are absolutely silent thanks to passive cooling: no fan or other moving parts Reconditioning (recovery) A lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulfation. Provided the process is stopped in time, it allows the sulfation to be partially reversed by charging the battery at low current until a higher voltage is reached Function to restore fully discharged batteries Most chargers with reverse polarity protection will not recognize a battery that has been discharged to zero volts or near zero volts and therefore will not recharge it. However, the Blue Power charger will attempt to recharge a fully discharged battery with low current and will resume normal charging after sufficient voltage has been established across the battery terminals optional accessories Blue Smart ip 65 12/15 bpc121531064r 12 v cigarette lighter plug with fuse 2 meter extension cable Terminals with fuses M6 cable lug connector with fuse Scope of delivery: 1x victron bpc121531064r blue smart ip65 12/15 12v 230v battery charger1x instruction manual1x connection terminals1x m8 cable lug connector

The Blue Smart ip22 12/15(3) charger from Victron Energy (mpn bpc121544002), is a professional, compact 12v 15a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The Blue Smart ip22 12/15(3) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 12v lead batteries and modern lithium batteries. It offers Highlights of the 12/15(3) Blue Smart ip22 Charger intelligent charging, until the perfect battery state... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 12/15(3) charger has built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the main technical features of the 12/15(3) Blue Smart ip22 Charger Victron Part number: bpc121544002 charges 12v lead-acid, gel, agm and lithium batteries 15a maximum charge current 3 battery charging outputs very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 12/15(3) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 12/15(3) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 12v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc121544002 12/15(3) ip22 Blue Smart Charger 1x instruction manual

The Blue Smart ip22 24/16(3) battery charger from Victron Energy (mpn bpc241644002), is a professional, compact 24v 16a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The Blue Smart ip22 24/16(3) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 24v lead batteries and modern lithium batteries. It offers Highlights of the 24/16(3) Blue Smart ip22 Charger intelligent charging, until the perfect battery state... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 24/16(3) charger has built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the most important technical features of the 24/16(3) Blue Smart ip22 Charger Victron Part number: bpc241644002 charges 24v lead acid, gel, agm and lithium batteries 16a maximum charge current 3 battery charging outputs very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 24/16(3) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 24/16(3) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 24v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc241644002 24/16(3) ip22 Blue Smart Charger 1x instruction manual

The Blue Smart ip 67 24/5 12v 230v battery charger from victron Energy (mpn bpc240513006) is a smart, high performance battery charger of the latest generation with 5a charging current for charging 24v agm, gel and lead acid batteries as well as lithium ion batteries. in terms of functionality, the Blue Smart ip67 series is identical to the chargers of the Blue Smart ip 65 and ip 22 device families except for a few functions. Only the operating environment for which these chargers are designed differs.The Blue Smart ip 67 battery chargers offer a wireless solution for monitoring voltage and current, adjusting settings and updating the charger when new features become available, thanks to integrated Bluetooth.important features of the Blue Smart ip67 24/5 5a battery charger victron Part number: bpc240513006 Model name: Blue Smart ip 67 24/5 max. charging current: 5a for battery voltage: 24v dc for mains voltage: 180-265 vac 45-65 Hz fully enclosed: waterproof, shockproof and fire retardant smart configuration and monitoring via integrated bluetooth and free app adaptive 5-step charging algorithm prolongs the life of your batteries thanks to integrated storage mode can be used to power 24v consumers high quality cast aluminum housing Protection against application errors: reverse polarity on battery (fuse), protection against overtemperature, protection against output short circuit fully encased: waterproof, shockproof and fire retardantWater, oil or dirt cannot damage the Blue Smart ip67 charger. The case is made of cast aluminum and the electronics are coated with resin.one of the highest charging efficiencies ever!Setting a new industry standard: With an efficiency of 92% or more, these chargers produce three to four times less heat.adaptive 5-stage charging algorithmThe Blue Smart 24/5 ip67 charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. "Bulk" (constant current phase) "Absorption" (constant voltage phase) "Recondition" (regeneration phase) "Float" (charge maintenance voltage phase) "Storage" (storage mode) Storage mode: less maintenance and aging when the battery is at restStorage mode is activated whenever there has been no discharge within 24 hours. In storage mode, the charge maintenance voltage is then lowered to 2.2 v/cell (13.2 v for a 24-v battery) to minimize gas generation and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure main differences with the Blue Smart ip 65 familyThe two groups of devices differ in the following respects: the protection class, the ip 67 devices have the best possible protection Blue Smart ip 65 devices have a 7-stage charging algorithm, the ip67 has a 5-stage algorithm Scope of delivery:1x victron bpc240513006 Blue Smart ip67 24/5 5a 24v 230v battery charger1x instruction manual1x 1,5m battery connection cable red/black

The Blue Smart ip22 12/30(3) charger from Victron Energy (mpn bpc123044002), is a professional, compact 12v 30a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The Blue Smart ip22 12/30(3) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 12v lead batteries and modern lithium batteries. It offers Highlights of the 12/30(3) Blue Smart ip22 Charger intelligent charging, until the perfect battery condition.... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 12/30(3) charger has built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the main technical features of the 12/30(3) Blue Smart ip22 Charger Victron Part number: bpc123044002 charges 12v lead acid, gel, agm and lithium batteries 30a maximum charge current 3 battery charging outputs very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 12/30(3) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 12/30(3) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 12v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc123044002 12/30(3) ip22 Blue Smart Charger 1x instruction manual

The blue smart ip65 12/25(1) 12v 230v battery charger (bpc122531064) is the latest professional, charger from Victron Energy with integrated Bluetooth module. It charges 12v batteries of various types and provided a maximum charging current of 25a. Together with the free VictronConnect app, you can thus easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain extent. technical highlights of the Blue Smart ip65 12/25(1)battery charger easy configuration and setup of the Blue Smart ip65 12/25(1) via Bluetooth interface max. 25a charging current, suitable for all 12v battery types solid protection against splash water. Dust and chemicals thanks to ip65 protection has several functions to extend battery life automatic temperature adjustment at low or high temperatures automatic power supply function 7-step intelligent charging algorithm can recover completely discharged batteries "dead batteries has low energy mode for charging small batteries Victron-Part number: bpc122531064 Lithium-ion battery mode ultra-efficient "green" battery charger With up to 95% efficiency, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, power consumption is reduced to 0.5 watts, five to ten times better than the industry standard durable, safe and quiet low heat load on electronic components protected against ingress of dust, water and chemicals. Protection against overheating: the output current is linearly reduced when the temperature rises up to 60 °c, so the charger will not fail even at extreme temperatures the chargers are absolutely silent thanks to passive cooling: no fan or other moving parts Reconditioning (recovery) A lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulfation. Provided the process is stopped in time, it allows the sulfation to be partially reversed by charging the battery at low current until a higher voltage is reached Restoring fully discharged batteries Most chargers with reverse battery protection will not recognize a battery that has been discharged to zero volts or near zero volts, and therefore will not recharge it. However, the Blue Power charger will attempt to recharge a fully discharged battery with low current and will resume normal charging after sufficient voltage has been established across the battery terminals optional accessories Blue Smart ip65 12/25(1) 12v cigarette lighter plug with fuse 2 meter extension cable Terminals with fuses M6 cable lug connector with fuse Scope of delivery: 1x Victron bpc122531064 Blue Smart ip65 12/25(1)230v battery charger for 12v batteries1x instruction manual1x connection terminals1x m8 cable lug connector

The Orion-Tr Smart 24/12-20 from victron Energy (mpn ori241224120) is a galvanically isolated dc-dc converter and charger. It is suitable for use in dual battery systems in vehicles or boats where the (smart) alternator and starter battery are to be used to charge the service battery. The charger can be used in 12v or 24v systems and is suitable for both lead-acid and lithium batteries. An unlimited number of units can be connected in parallel to increase the output power. Thanks to the Orion-Tr Smart 24/12-20a you can supply any 12v consumer with exactly the right voltage. The correct voltage is guaranteed even with longer lines, because the Orion can adjust the voltage to any line losses that occur. For many sensitive electronic devices, maintaining the exact operating voltage is essential for smooth operation. Integrated Bluetooth, fully programmable monitoring, changing settings and updating the charger when new software features become available can be done with any Bluetooth-enabled smartphone, tablet or other device. The Orion-Tr Smart can be programmed with a configurable battery charging algorithm or a fixed output. It also features smart generator compatibility - engine run detection. Features of the Orion-Tr Smart 24/12-20a 240w (galvanically isolated) victron Energy part number: ori241224120 for 24 v battery voltage, adjustable output voltage 10-15 v max. 240 w output power at a maximum current of 30 A wide input voltage range: 20-35 v Protection class ip43, galvanic isolation 200 vDC between input, output and housing can be connected in parallel with any number of identical devices to increase output power can be used for buffer charging of batteries remote on/off switch intelligent generator compatibility: engine run detection Adaptive 3-stage charging algorithm: constant current - constant voltage - conservation For lead-acid batteries, it is important to keep the recording time short during shallow discharges to avoid overcharging the battery. After a deep discharge, the constant voltage duration is automatically extended to ensure that the battery charges fully. For lithium batteries, the recording time is fixed, by default 2 hours. Alternatively, a fixed output voltage can be selected. Remote on/off switch A remote on/off switch or a relay contact can be connected to the two-pin connector. Alternatively, the h terminal (right) of the two-pin plug can be connected to a battery positive terminal or the l terminal (left) of the two-pin plug can be connected to the battery negative terminal (or to the body of a vehicle, for example). scope of delivery: 1x victron Energy ori241224120 Orion-Tr Smart 24/12-20a 240 w dc-dc converter 1x instruction manual

The Blue Smart ip22 12/20(3) charger from Victron Energy (mpn bpc122044002), is a professional, compact 12v 20a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The Blue Smart ip22 12/20(3) charger can be used with equipment in your workshop or with motor vehicles such as with (classic) cars, motorcycles, boats and motorhomes and charges both classic 12v lead batteries and modern lithium batteries. It offers Highlights of the 12/20(3) Blue Smart ip22 Charger intelligent charging, until the perfect battery condition.... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life Restoring deep-discharged "dead" batteries Unlike most other brands and product lines, the Blue Smart ip22 charger will attempt to recharge a deep-discharged battery by imposing a weak charging current on it. Normal charging operation will then resume once sufficient voltage is present between the battery terminals. Retrieving battery status remotely, with the VictronConnect app The Blue Smart ip22 12/20(3) charger features built-in Bluetooth. This allows the status of the charger and battery to be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect App the most important technical features of the 12/20(3) Blue Smart ip22 Charger Victron Part number: bpc122044002 charges 12v lead-acid, gel, agm and lithium batteries 20a maximum charge current 3 battery charging outputs very compact dimensions: 235 x 108 x 65mm highly advanced, seven-stage charging algorithm with integrated Bluetooth for use with the free VictronConnect app other features of the 12/20(3) Blue Smart ip22 battery charger trend-setting efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, about five to ten times better than the industry standard. adaptive 7-stage charging algorithm The 12/20(3) Blue Smart charger features microprocessor-controlled "adaptive" battery management. "Adaptive" means that the charging process is automatically adjusted to the type of battery usage. Storage mode: less maintenance and aging when the battery is at rest Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2v for a 12v battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy bpc122044002 12/20(3) ip22 Blue Smart Charger 1x instruction manual

The Blue Smart ip65 12/10 12v 230v battery charger (bpc121031064r) is the latest professional, charger from victron Energy with built-in Bluetooth. It is designed to charge 12v batteries of various types and provide a maximum charging current of 10a. Together with the free victronConnect App you can easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain degree.technical highlights of the Blue Smart ip65 12/10 battery charger easy configuration and setup of the Blue Smart ip65 12/10 via Bluetooth interface suitable for all 12v battery types max. 10a charging current solid protection against splash water. Dust and chemicals thanks to ip65 protection has several functions to extend battery life automatic temperature adjustment at low or high temperatures automatic power supply function 7-step intelligent charging algorithm can recover fully discharged batteries "dead batteries has low energy mode for charging small batteries victron-Part number: bpc121031064r Lithium-ion battery mode ultra-high efficiency "green" battery charger With up to 95% efficiency, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, power consumption is reduced to 0.5 watts, five to ten times better than the industry standard durable, safe and quiet low heat load on electronic components protected against dust, water and chemical ingress. Protection against overheating: the output current is linearly reduced when the temperature rises up to 60 °c, so the charger does not fail even at extreme temperatures the chargers are absolutely silent thanks to passive cooling: no fan or other moving parts Reconditioning (recovery) A lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulfation. Provided the process is stopped in time, it allows the sulfation to be partially reversed by charging the battery at low current until a higher voltage is reached Function to restore fully discharged batteries Most chargers with reverse polarity protection will not recognize a battery that has been discharged to zero volts or near zero volts and therefore will not recharge it. However, the Blue Power charger will attempt to recharge a fully discharged battery with low current and will resume normal charging after sufficient voltage has been established across the battery terminals optional accessories Blue Smart ip 65 12/10 bpc121031064r 12 v cigarette lighter plug with fuse 2 meter extension cable Terminals with fuses M6 cable lug connector with fuse Scope of delivery: 1x victron bpc121031064r Blue Smart ip65 12/7 12v 230v battery charger1x instruction manual1x connection terminals1x m8 cable lug connector