The solar module 150w mono from Offgridtec (mpn 3-01-001255) works with monocrystalline solar cells with a high efficiency of >22,3% and is ideal for 12v systems thanks to its 20v operating voltage. In Offgridtec mono solar modules only cells of the highest quality grade are installed and guarantee a constant high quality and performance with maximum service life thanks to state-of-the-art manufacturing. Features of Offgridtec 150w 12v mono solar panel proven quality directly from Offgridtec manufactured according to the latest standards monocrystalline solar cells extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v systems on land or in mobile solar systems 2 bypass diodes - minimized power loss in shaded conditions The mono 150w 12v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtecs experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. It can withstand heavy hail and storms or extreme cold and heat without any problems and thanks to the integrated bypass diodes, the module can continue to produce power even in shaded or low light conditions. The most important technical data at a glance Power (Pmax): 150w Working voltage (Vmp): 20 V Open circuit voltage (Voc): 24 V max. current (Imp): 7.5 A Short circuit current (Isc): 8.1 A max. system voltage: 1000 V permissible ambient temperature: -40°C - +85°C Dimensions: 1140 x 680 x 35 mm Weight: 12 kg Universally applicable Offgridtecs 150w 12v Mono is universally applicable for example in 12 Volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. The connection cables are 80 cm long and equipped with MC4 connectors. Scope of delivery: Offgridtec 3-01-001255 150w mono 12v solar panel

The solar module 5w mono from Offgridtec (mpn 3-01-002960) works with monocrystalline solar cells with a high efficiency of >22,3% and is ideal for 12v systems thanks to its 20v operating voltage. In Offgridtec mono solar modules only cells of the highest quality grade are installed and guarantee thanks to modern manufacturing a constant high quality and performance with maximum service life. Features of Offgridtec 5w 12v mono solar panel proven quality directly from Offgridtec manufactured according to the latest standards monocrystalline silicon solar cells extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v systems on land or in mobile solar systems Frame in anodized aluminum The mono 5w 12v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtecs experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. It can withstand heavy hail and storms or extreme cold and heat without any problems and thanks to the integrated bypass diodes, the module can continue to produce power even in shaded or low light conditions. The most important technical data at a glance Power (Pmax): 20W Working voltage (Vmp): 17.8V Open circuit voltage (Voc): 22.3 V max. current (Imp): 0.28 A Short circuit current (Isc): 0.3 A max. system voltage: 600 V permissible ambient temperature: -40°C - +85°C Dimensions: 250 x 180 x 25 mm Weight: 0,6 kg Universally applicable Offgridtecs 5w 12v Mono is universally applicable for example in 12 Volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. The solar panel is supplied without connection cable. Scope of delivery: Offgridtec 3-01-002960 5w mono 12v solar panel

The Offgridtec olp 180w (mpn 3-01-013105) is a high-performance 12v solar module with innovative overlapping design, wafer assembly and features dimensions that until now only high-performance solar modules could achieve. The shingle arrangement of the wafers ensures an optimal current flow through minimized power losses and a significantly higher module efficiency through better space utilization. The perc technology used improves light absorption and increases the power yield. Unique selling points of the olp series from Offgridtec® Unique module design with overlapping wafer arrangement (overlapping design) ensures very high module efficiency through better area utilization and reduced power losses due to line resistances Modern, homogeneous appearance without visible conductor tracks Innovative perc technology ensures improved absorption at longer wavelengths, e.g. at flat irradiation angles (early morning or evening) or in cloudy conditions No hotspot hazard Less loss in case of partial shading Thanks to finishing according to overlapping design, the module has a footprint of just 680 x 1330 x 35 mm at a rated power of 180w Cell efficiency of over 23 Innovative perc technology The perc technology (Passivated Emitter Rear Cell) in the Offgridtec olp solar modules ensures a higher efficiency of the solar cells with its key technology. A dielectric layer is created on the back of the cell between the conventional aluminum metallization and the silicon wafer layer, which is provided with tiny holes by a laser. This dielectric layer reflects light, which penetrates to the back side without generating charge carriers, into the solar cell. The reflection gives the photons a "second chance" to generate electricity. In addition to higher efficiency at different wavelengths and the increased likelihood that electrons will contribute to power, perc technology contributes to lower system costs and an increase in area energy yield. Technical data: Generator power: 180 Wp Module voltage (Vmp): 24.8 V Max. Current (Imp): 7.26 A Open circuit voltage (Voc): 29.76 V Short circuit current (Isc): 7.84 A Max. System voltage: 600v DC Dimensions: 680 x 1330 x 35 mm Weight: 11,54 kg Scope of delivery: 1x Offgridtec® olp 180w 12v perc overlapping solar panel 12v shingle technology

100W / 12V solar panel with monocrystalline solar cells. Ideal for 12V-systems. Features: Monocrystalline solar cells 2 bypass-diodes: minimizes power degradation during shady periods Surface: hardened ESG-solarglass and weather resistant coating Frame: anodized aluminium Connection cable: 80cm; MC4 plug Ideal for 12V-systems Performance guarantee: < 10 years - 90%; <25 years 80% For the production of our modules we only use high-quality monocrystalline solar cells. The module frame made of anodized aluminium and a special ESG-solar glass make the module very resistant against abrasion.  

The 120 watt etfe-al semi-flexible solar panel from Offgridtec (3-01-011050) is based on a new, groundbreaking material composition (aluminum-etfe) and is equipped with highly effective mono-cells from Germany. The output voltage is 19,8v dc which makes it very interesting for a wide range of application scenarios. It is also walkable and much more slip resistant than its predecessors making it the perfect choice for marine and mobile applications. The power is supplied by the latest high efficiency cells, which thanks to current technology have a remarkable cell efficiency and also stand out from the crowd with low power degradation values. Unique selling points of the etfe-al series of Offgridtec On the front side of the module, 2 superimposed etfe layers ensure solid protection of the inner cells and a high light yield for many years. Thanks to a new structure of the outermost layer, slip inhibition has been significantly improved and the module can be walked on without any problems. Long-term higher yields due to better light transmission and significantly less clouding of the transparent etfe front layers compared to conventional solar modules with different front coatings. In addition, the solid etfe front provides strong protection against hail and makes the module absolutely resistant to salt water. Current management is handled by 5 busbars, ensuring solid throughput without heat loss even at high currents. The integrated AL backsheet virtually eliminates the occurrence of cell cracks due to mishandling or mounting. The series is equipped with highly effective solar cells (Made in Germany), which offer a high cell efficiency of 18.43 percent. The final production of the modules is carried out using the most modern manufacturing processes. Technical features of the etfe-al Power (Pmax): 120 Wp Voltage (Vmp): 19,8 V max. current (Imp): 6,06 A Short circuit current (Isc): 6,55 A Open-circuit voltage (Voc): 23.3 V max. system voltage: 200 V Dimensions: 980 x 680 x 4 mm Weight: 4 Kg Material composition: aluminum, etfe walkable: Yes Bendable: max. 10° (L) Scope of delivery: 1x Offgridtec 3-01-011050 etfe-al 120w 20v semi-flexible solar panel alu backsheet

The Offgridtec olp 100w (mpn 3-01-011070) is a powerful 12v solar module with innovative overlapping design wafer assembly and features dimensions that almost reach the range of high power solar modules. The shingle arrangement of the wafers ensures optimal current flow due to minimized power losses and significantly higher module efficiency due to better space utilization. The PERC technology used improves light absorption and increases the power yield. Unique selling points of the olp series of Offgridtec Unique module design with overlapping wafer arrangement (overlapping design) ensures very high module efficiency through better area utilization and reduced power losses due to line resistances. Modern, homogeneous appearance without visible conductor tracks. Innovative PERC technology ensures improved absorption at longer wavelengths, e.g. at flat irradiation angles (early morning and evening) or in cloudy conditions No hotspot hazard Less loss in case of partial shading Thanks to finishing according to overlapping design, the module has a footprint of just 988 x 560 x 30mm at a rated power of 100w. The cell efficiency is over 23%. Innovative PERC technology The PERC technology (Passivated Emitter Rear Cell) in the Offgridtec olp solar modules ensures a higher efficiency of the solar cells with its key technology. A dielectric layer is created on the back of the cell between the conventional aluminum metallization and the silicon wafer layer, which is provided with tiny holes by a laser. This dielectric layer reflects light, which penetrates to the back side without generating charge carriers, into the solar cell. The reflection gives the photons a "second chance" to generate electricity. In addition to higher efficiency at different wavelengths and the increased likelihood that electrons will contribute to power, PERC technology contributes to lower system costs and an increase in area energy yield. Scope of delivery: 3-01-011070 Offgridtec® olp 100w 12v PERC overlapping solar panel 12v shingle technology

The Offgridtec olp 155w (mpn 3-01-011075) is a powerful 12v solar module with innovative overlapping design wafer assembly and features dimensions that until now only high-performance solar modules could achieve. The shingle arrangement of the wafers ensures an optimal current flow through minimized power losses and a significantly higher module efficiency through better space utilization. The perc technology used improves light absorption and increases the power yield. Unique selling points of the olp series of Offgridtec Unique module design with overlapping wafer arrangement (overlapping design) ensures very high module efficiency through better area utilization and reduced power losses due to line resistances. Modern, homogeneous appearance without visible conductor tracks. Innovative perc technology ensures improved absorption at longer wavelengths, e.g. at flat irradiation angles (early morning or evening) or in cloudy conditions No hotspot hazard Less loss in case of partial shading Thanks to finishing according to overlapping design, the module has a footprint of just 650 x 1310 x 35mm at a rated power of 155w. The cell efficiency is over 23%. Innovative perc technology The perc technology (Passivated Emitter Rear Cell) in the Offgridtec olp solar modules ensures a higher efficiency of the solar cells with its key technology. A dielectric layer is created on the back of the cell between the conventional aluminum metallization and the silicon wafer layer, which is provided with tiny holes by a laser. This dielectric layer reflects light, which penetrates to the back side without generating charge carriers, into the solar cell. The reflection gives the photons a "second chance" to generate electricity. In addition to higher efficiency at different wavelengths and the increased likelihood that electrons will contribute to power, perc technology contributes to lower system costs and an increase in area energy yield. Scope of delivery: Offgridtec® olp 155w 12v perc overlapping solar panel 12v shingle technology

The 160 watt etfe-alu semi-flexible solar panel from Offgridtec (3-01-012500) is based on a new, groundbreaking material composition (aluminum-etfe) and is equipped with highly effective mono-cells. The output voltage is 12vdc which makes it very interesting for a wide range of application scenarios. It is also walkable and much more slip resistant than its predecessors making it the perfect choice for marine and mobile applications. The power is supplied by state-of-the-art solar cells, which, thanks to the latest technology, have a remarkable cell efficiency and also stand out from the crowd due to low power degradation values. Unique selling points of the etfe alu series from Offgridtec On the front side of the module, 2 superimposed etfe layers ensure solid protection of the inner cells and a high light yield for many years. Thanks to a new structure of the outermost layer, the slip inhibition has been significantly improved and the module can be walked on without any problems. Long-term higher yields due to better light transmission and significantly less clouding of the transparent etfe front layers compared to conventional solar modules with different front coatings. In addition, the solid etfe front provides strong protection against hail and makes the module absolutely resistant to salt water. Current management is handled by 5 busbars, ensuring solid throughput without heat loss even at high currents. Due to the integrated alu-backsheet, the occurrence of cell cracks due to incorrect handling or mounting is almost impossible. The etfe-Alu series is equipped with state-of-the-art mono-cells, which offer a high cell efficiency of <22 percent. The final production of the modules is carried out using state-of-the-art manufacturing processes. Technical features of the etfe-alu Power (Pmax): 160 Wp Voltage (Vmp): 19,8 V max. current (Imp): 8,08 A Open-circuit voltage: 23.3 V Short circuit current (Isc): 8,73 A max. system voltage: 200 V Dimensions: 1260 x 680 x 4 m Weight: 6.3 Kg Material composition: aluminum, etfe walkable: Yes Bendable: max. 10° (L) Scope of delivery: 1x Offgridtec 3-01-012500 etfe-alu 160w 12v semi flexible solar panel alu backsheet

The solar module 130w mono from Offgridtec (mpn 3-01-001250) works with monocrystalline solar cells with a high efficiency of >18,5% and is ideal for 12v systems thanks to its 20v operating voltage. In Offgridtec mono solar modules only cells of the highest quality grade are installed and guarantee a constant high quality and performance with maximum service life thanks to state-of-the-art manufacturing. Features of Offgridtec 130w 12v mono solar panel proven quality directly from Offgridtec high operating voltage of 20v, perfect for 12v systems manufactured according to the latest standards monocrystalline solar cells extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v systems on land or in mobile solar systems 2 bypass diodes - minimized power loss in shaded conditions 3 busbars The mono 130w 12v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtecs experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. It can withstand heavy hail and storms or extreme cold and heat without any problems and thanks to the integrated bypass diodes, the module can continue to produce power even in shaded or low light conditions. The most important technical data at a glance Power (Pmax): 130w Working voltage (Vmp): 20 V Open circuit voltage (Voc): 24 V max. current (Imp): 6.5 A Short circuit current (Isc): 7.02 A max. system voltage: 1000 V permissible ambient temperature: -40°C - +85°C Dimensions: 1020 x 680 x 35 mm Weight: 10 kg Universally applicable Offgridtecs 130w 12v Mono is universally applicable for example in 12 volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. The connection cables are 80 cm long and equipped with MC4 connectors. Scope of delivery: Offgridtec 3-01-001250 130w mono 12v solar panel

The fsp-2 225w 12v is the largest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in the range. It has a 5-sided design and comes with a matching connection kit, which allows you to quickly and easily connect to the charge controller of your choice and the battery to be charged. The fsp-2 225w 12v can be ordered in three variants. Offgridtec is also happy to customize any fsp module in terms of cable set and charging technology on request. The connection kit is stored in a lockable bag, directly on the module. So you always have a ready to use small power plant at your side. Performance that sets standards The fsp-2 225w Ultra is equipped with American SPR back-contact cells from a well-known manufacturer. The cells are completely black, which gives the fsp-2 225w a very modern, high-quality look. The SPR cells provide a very high efficiency of the panel and set in combination with the low weight and compact dimensions of the fsp-2 panel new standards in this power class. extensive application possibilities: excellent usable in the camping area or for expeditions, climbing tours and much more... for vehicles and boats without fixed solar installation ... and numerous other applications in different areas... technical highlights fsp 2 225w ultra foldable solar panel Rated power: 225wp Number of sides: 5 x 45 Wp Module voltage (Vmp): 37,2V Max. Charge current (Imp): 6,05A Open circuit voltage (Voc): 43,7V Short circuit current (Isc): 6,41A Dimensions closed: 560 x 440 x 40 mm Dimensions open designed: 560 x 2430 x 8 mm Weight: 6 kg ETFE coating SunPower high performance cells 6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side 0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller) 1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on the battery side Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse the included Profi-Connection Kit The connection kit included in the scope of delivery offers everything needed for a quick start-up of the mobile solar set. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal alligator clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse. customizable on request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp-2 series As with all Offgridtec solar module series, great emphasis has been placed on high quality and durability in the fsp series. The fsp 2 225w Ultra uses back-contacted solar cells like those used in our SP high performance series. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp 2 series is coated with ETFE for better protection and very high light transmission. Furthermore, we produce our solar modules according to current norms and standards, which together with the high quality materials makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions. Scope of delivery 1x Offgridtec fsp-2 225w 12v, 3-01-010765 1x Offgridtec fsp-2 Connection-Kit

The 100w etfe-al semi-flexible solar panel from Offgridtec (3-01-011045) is based on a new, groundbreaking material composition (aluminum-etfe) and is equipped with highly effective mono-cells. The output voltage is 19,8v dc which makes it very interesting for a wide range of application scenarios. It is also walkable and much more slip resistant than its predecessors making it the perfect choice for marine and mobile applications. The power is supplied by state-of-the-art solar cells, which, thanks to the latest technology, have a remarkable cell efficiency and also stand out from the crowd due to low power degradation values. Unique selling points of the etfe-al series of Offgridtec On the front side of the module, 2 superimposed etfe layers ensure solid protection of the inner cells and a high light yield for many years. Thanks to a new structure of the outermost layer, slip inhibition has been significantly improved and the module can be walked on without any problems. Long-term higher yields due to better light transmission and significantly less clouding of the transparent etfe front layers compared to conventional solar modules with different front coatings. In addition, the solid etfe front provides strong protection against hail and makes the module absolutely resistant to salt water. Current management is handled by 5 busbars, ensuring solid throughput without heat loss even at high currents. Due to the integrated AL backsheet, the occurrence of cell cracks due to incorrect handling or mounting is almost impossible. The series is equipped with the best solar cells, which offer a high cell efficiency of 22,3 percent. The final production of the modules is carried out using the most modern manufacturing processes. Technical characteristics of the etfe-al Power (Pmax): 100 Wp Voltage (Vmp): 19,8V max. current (Imp): 5,05 A Short circuit current (Isc): 5,45 A max. system voltage: 200V Dimensions: 680 x 830 x 4 mm Weight: 4 Kg Material composition: aluminum, etfe walkable: Yes Bendable: max. 10° (L) Scope of delivery: 1x Offgridtec 3-01-011045 etfe-al 100w 12v semi-flexible solar panel alu backsheet

The fsp-2 195w 12v is the second largest and newest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in the range. It has a 3-sided design and comes with a matching connection kit that allows you to quickly and easily connect to the charge controller of your choice and the battery to be charged. Performance that sets standards The fsp-2 195w Ultra is equipped with American SPR back-contact cells from a well-known manufacturer. The look of the cells is completely black, which also gives the fsp-2 180w a very modern, high-quality look. The SPR cells ensure a very high efficiency of the panel and set new standards in this power class in combination with the low weight and compact dimensions of the fsp-2 panel. extensive application possibilities: excellent usable in the camping area or for expeditions, climbing tours and much more... for vehicles and boats without fixed solar installation ... and numerous other applications in different areas... technical highlights fsp-2 195w ultra foldable solar panel Rated power: 195wp Number of sides: 3 x 69wp Module voltage (Vmp): 33,5 V Max. Charge current (Imp): 5,82 A Open circuit voltage (Voc): 39,4 V Short circuit current (Isc): 6,17 A Dimensions closed: 820 x 440 x 40 mm Dimensions open designed: 820 x 1545 x 6 mm Weight: 8,2 Kg ETFE coating SunPower high performance cells 6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side 0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller) 1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on battery side Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse Including Victron SmartSolar 75/15 charge controller The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 15a max charge current for charging 12v and 24v batteries. Unlike the Bluesolar 75/15, the Smart version has integrated Bluetooth, which eliminates the need to purchase a Bluetooth dongel. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control gx or the mppt Control. The integrated Bluetooth in the SmartSolar series is the wireless solution to setup, monitor and update the controller using Apple and Android smartphones, tablets or other devices. The most important technical features at a glance 15a load output high peak efficiency of 98 freely programmable battery charging algorithm (via the free Victron Connect APP) Light dimming functions programmable (via the free Victron Connect APP) Ultra fast maximum power point tracking max. PV open circuit voltage: 75V Charging algorithm: multi-stage, adaptive integrated Bluetooth module Dimensions: 100 x 113 x 40 mm Weight: 0,5 kg The included Profi-Connection Kit The included connection kit provides everything needed to get the mobile solar set up and running quickly. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal alligator clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse. Customizable on request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp-2 series As with all Offgridtec solar module series, great emphasis has been placed on high quality and durability in the fsp series. The fsp 2 195w Ultra uses back-contacted solar cells like those used in our SP high performance series. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp 2 series is coated with ETFE for better protection and very high light transmission. Furthermore, we produce our solar modules according to current norms and standards, which together with the high quality materials makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions. Scope of delivery 1x Offgridtec fsp-2 195w 12v, 3-01-012680 with Victron SmartSolar 75/15 mppt charge controller 1x Offgridtec fsp-2 connection kit  

The fsp-2 195w 12v is the second largest and newest member of the Offgridtec fsp family and is also one of the most powerful foldable solar modules in the range. It has a 3-sided design and comes with a matching connection kit that allows you to quickly and easily connect to the charge controller of your choice and the battery to be charged. Performance that sets standards The fsp-2 195w Ultra is equipped with American SPR back-contact cells from SunPower. The look of the cells is completely black, which also gives the fsp-2 195w a very modern, high-quality look. The SPR cells ensure a very high efficiency of the panel and set new standards in this power class in combination with the low weight and compact dimensions of the fsp-2 panel. extensive application possibilities: excellent usable in the camping area or for expeditions, climbing tours and much more... for vehicles and boats without fixed solar installation ... and numerous other applications in different areas... technical highlights fsp-2 195w ultra foldable solar panel Rated power: 195wp Number of sides: 3 x 65 Wp Module voltage (Vmp): 33,5 V Max. Charge current (Imp): 5,82 A Open circuit voltage (Voc): 39,4 V Short circuit current (Isc): 6,17 A Dimensions closed: 820 x 440 x 40 mm Dimensions open designed: 820 x 1545 x 60 mm Weight: 7,12 Kg ETFE coating SunPower high performance cells 6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side 0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller) 1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on the battery side Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse the included Profi-Connection Kit The connection kit included in the scope of delivery offers everything needed for a quick start-up of the mobile solar set. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal crocodile clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse. customizable on request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp-2 series As with all Offgridtec solar module series, high quality has been emphasized in the fsp-2 series. The fsp-2 195w works with highly effective solar cells. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp-2 series is coated with ETFE coating, which provides better protection and at the same time ensures very high light transmittance. Furthermore, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions. Scope of delivery 1x Offgridtec fsp-2 195w 12v, 3-01-012680 1x Offgridtec fsp-2 Connection-Kit

The FSP-Max 440w from Offgridtec (mpn 014560) is a foldable high-end solar module with connection kit, as well as firmly integrated fold-out supports, in order to be able to set up the module easily and everywhere at a 45 degree angle. The module is equipped with high-efficiency monocrystalline solar cells and delivers 440w of solar power in optimal orientation and sunshine. The combination of the compact dimensions when closed and the low total weight of just under 13kg sets new standards in terms of flexibility and efficiency of mobile solar modules. The supply of mobile or permanently installed energy storage units is thus possible flexibly and easily. The solution for solar-assisted mobile battery charging In the camping area For expeditions For vehicles and boats without fixed solar installation For off-grid power supply at home And numerous other applications in a wide variety of areas Important features: High output power Compatible with a wide range of 1-2.5 kWh mobile power stations Made of high quality polymer composite Quickly assembled and connected Cell efficiency of over 22 Compact dimensions With practical carrying handle and protective bag Easy to use anywhere Four feet are permanently attached to the solar case, which can be easily folded out if necessary to place the panel on the ground at a bang 45 degrees. Thus, the module is fully assembled and ready for use within a minute. The angled orientation ensures an ideal solar yield. In combination with the low weight, the folding module with the compact dimensions and the practical carrying handle is suitable for many different applications and is without much effort, quickly ready for use. The included Profi-Connection Kit The connection kit included in the scope of delivery contains everything that is needed for a quick start-up of the mobile solar module. It has a 6m connection cable, which is equipped with a high-quality Anderson connector at one end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of your charge controller and is equipped with the corresponding Anderson connector on the other end. This allows you to connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1m long plug&play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal alligator clips on the battery side, ,which can be easily connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with appropriate fuse. With the 6m connection cable can, with a suitable adapter, also be connected to a suitable power station (with integrated charge controller) Technical data Rated power (Pmax): 440w (4x110W) Module voltage (Vmp): 40v Module current max (Imp): 11a Open circuit voltage (Voc): 48v Short circuit current (Isc): 12a Max. System voltage: 200V/DC Cell efficiency: 22.62% Cell type: Monocrystalline Weight: 13.2kg Dimensions closed: 1072 x 547 x 90 mm Dimensions opened: 1072 x 2188 x 22.5 mm Scope of delivery: 1x Offgridtec FSP-Max 440w foldable solar panel 1x professional connection kit 1x protective bag

The fsp-2 135w ultra mppt kit 12v is a combination of the foldable 135w fsp-2 solar panel and a latest generation smart mppt controller. The fsp-2 135w is one of the newest models in the family and also one of the most powerful foldable solar panels available. It has a 3-sided design and is delivered with a matching Connectino Kit with which you can quickly and easily establish a connection to the charge controller and the battery to be charged. In terms of charging technology, we rely on the fsp-2 135w kit mppt on the high-quality Victron Smart-Solar 75/15 charge controller. A high quality device which can be conveniently controlled via Bluetooth and a free app and is also equipped with a 15a load output for DC consumers. The connection kit is housed in a lockable bag, directly on the module. So you always have a ready-to-use, small power plant at your side. Performance that sets standards The fsp-2 135w Ultra is equipped with American SPR back-contact cells from a well-known manufacturer. The look of the cells is completely black, which additionally gives the fsp-2 135w a very modern, high-quality look. The SPR cells ensure a high efficiency of the panel and, in combination with the low weight and compact dimensions of the fsp-2 panel, set new standards in this power class. Extensive range of applications: Excellent for use in camping applications Or for expeditions, climbing tours, etc For vehicles and boats without fixed solar installation And numerous other applications in different areas Technical highlights fsp-2 135w solar panel Rated power: 135wp, number of sides: 3 x 45 Wp Dimensions closed: 560 x 440 x 20 mm; open designed: 560 x 1545 x 6 mm Weight module: 5.1 kg equipped with high-end solar cells Module voltage (Vmp): 19,8v - Max. Charge current (Imp): 6.82A Open circuit voltage (Voc): 23.3v - Short circuit current (Isc): 7.22A ETFE coating SunPower high power cells 6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side 0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller) 1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on the battery side Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse Including Victron SmartSolar mppt 75/15 charge controller The Smartsolar 75/15 from Victron Energy (mpn scc075015060r) is a mppt solar charge controller with 15a max charge current for charging 12v and 24v batteries. Unlike the BlueSolar 75/15, the Smart version has built-in Bluetooth, eliminating the need to purchase a Bluetooth dongle. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control gx or the mppt Control. The integrated Bluetooth in the SmartSolar series is the wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices. The most important technical features of the charge controller at a glance 15a load output high peak efficiency of 98 freely programmable battery charging algorithm (via the free Victron Connect app) Light dimming functions programmable (via the free Victron Connect app) Ultra fast maximum power point tracking max. PV open circuit voltage: 75V Charging algorithm: multi-stage, adaptive integrated Bluetooth module Dimensions: 100 x 113 x 40 mm Weight: 0,5 kg The included Profi-Connection Kit The included connection kit provides everything needed to get the mobile solar set up and running quickly. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller and is also equipped with an Anderson connector on the other side. This allows you to quickly connect or disconnect the controller at any time using the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal alligator clips on the battery side, which are compatible and can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse. Customizable upon request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp-2 series As with all Offgridtec solar module series, great emphasis has been placed on high quality and durability in the FSP series. The fsp-2 135w Ultra uses back-contacted solar cells like those used in our SP high performance series. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp-2 series is coated with an ETFE coating, which provides better protection and at the same time ensures a very high light transmission. Furthermore, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions. Scope of delivery: 1x Offgridtec fsp-2 135w 12v, 3-01-010755 1x Victron Energy scc075015060r SmartSoalr mppt 75/15 15a 12v 24v solar charge controller 1x Offgridtec fsp-2 connection kit

The fsp-2 135w Ultra is a foldable high-end solar panel with battery connection clamps as well as 3 integrated fold-out supports that allow you to easily set up the fsp-2 panel anywhere at a 45 degree angle. The fsp-2 Ultra is the successor of our mp-105w and is equipped with highly effective solar cells and provides a full 120w of solar power at optimal orientation and sunshine. Together with the very compact dimensions when folded and the low overall weight, the fsp-2 sets new standards in flexibility and efficiency among mobile, foldable solar modules. The price of the new Offgridtec fsp-2 Ultra also sets standards among comparable panels and stands up to any comparison. The basic solution for solar-assisted, mobile charging of batteries up to max. 200Ah: in the camping area for expeditions for vehicles and boats without fixed solar installation and numerous other applications in different areas Technical data foldable solar panel fsp-2 135w Ultra Rated power: 135wp Module voltage (Vmp): 19.8V Max. Charging current (Imp): 6,82A Open circuit voltage (Voc): 23.3V Short circuit current (Isc): 7,22A Charge controller: not included Dimensions closed: 560 x 440 x 20 mm Dimensions open designed: 560 x 1545 x 6 mm Weight: 5.1 kg ETFE coating SunPower high performance cells 6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side 0,5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller) 1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on the battery side Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse The included Profi-Connection Kit The connection kit included in the scope of delivery offers everything needed for a quick start-up of the mobile solar set. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal alligator clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse. Easy to set up thanks to 3 firmly integrated feet Three feet are sewn to the pocket of the fsp, which can be easily folded out to place the panel on the ground at an angle of 45 degrees. Thus, the module is fully assembled and ready for use within one minute. Customizable on request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp-2 series As with all Offgridtec solar module series, the fsp-2 series is designed with high quality in mind. The fsp-2 120 uses high performance solar cells from SunPower. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp-2 series has an ETFE coating, which provides better protection and at the same time ensures very high light transmission. Furthermore, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions.

The fsp 2 135w Ultra is a foldable high-end solar panel with integrated charge controller, battery terminals as well as 3 integrated fold-out supports with the help of which you can set up the fsp 2 panel easily and anywhere at a 45 degree angle. The fsp 2 Ultra is the successor of our mp-105w and is equipped with the latest spr back-contact cells and delivers a whopping 135w of solar power in optimal orientation and sunshine. Together with the very compact dimensions when folded and the low overall weight, the fsp 2 sets new standards in terms of flexibility and efficiency among mobile, foldable solar modules. The price of the new Offgridtec fsp 2 Ultra also sets standards among comparable panels and stands up to any comparison. The basic solution for solar-powered, mobile charging of batteries up to max. 200Ah: in the camping area for expeditions for vehicles and boats without fixed solar installation and numerous other applications in different areas overview power management fsp 2 135w Ultra Supported battery types (12v): agm, lead acid, gel usb output: 1a 5v directly to the charge controller 12v consumer output: 10a 12v directly on charge controller Technical data foldable solar panel fsp 2 135w Ultra Module voltage (Vmp): 19,8V Max. Charging current (Imp): 6,82A Open circuit voltage (Voc): 23,3V Short circuit current (Isc): 7,22A Charge controller: Offgridtec pwm Pro 12/24-10 Supported battery types(12v): agm, lead acid, gel 2 usb outputs: 5v max 2,4A directly on charge controller 12v consumer output: 10a 12v directly on charge controller Dimensions closed: 560 x 440 x 20 mm Dimensions open designed: 560 x 1545 x 6 mm Weight: 5,1 kg Cable length module to controller: 6,5m Cable length controller to battery: 1m Battery connection: alligator clips Rated power: 120WP Technical note: The charge controller is positively grounded - this may cause problems when connecting to a system where the ground is grounded to negative easy to set up thanks to 3 firmly integrated feet Three feet are sewn to the pocket of the fsp, which can be easily folded out to place the panel on the ground at an angle of 45 degrees. Thus, the module is fully assembled and ready for use within one minute. Offgridtec pwm Pro charge controller 10a The Offgridtec pwm 12/24-10 (mpn 1-01-010910) is a microprocessor controlled solar charge controller with 10a max charge power and can charge both 12v and 24v batteries. It uses advanced 3-stage pwm modulation to get the most out of your agm, gel or lead acid batteries. It is suitable for Solarasystems of 130w at 12v and 260w at 24v battery voltage. Features pwm pro charge controller 10a max. charge current 10a, for up to 130w PV power at 12v and 260w at 24v systems modern, 3-stage pwm charge control for gentle and efficient charging of your battery(ies) 3 battery types adjustable, agm, gel and liquid lead acid intuitive operation via 2 buttons directly on the device large LCD display with numerous display options, incl. kWh meter 2 usb-ports with a maximum output power of 2.4A Load output with numerous configuration options, e.g. for light control Temperature compensated battery charging (optional temperature sensor required, not included) customizable on request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp series As with all Offgridtec solar module series, the fsp-2 series is designed with high quality in mind. The fsp-2 120 uses back-contacted solar cells like those used in our SP high-performance series. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions.

The solar module 30w mono from Offgridtec (mpn 3-01-001530) works with monocrystalline solar cells with a high efficiency of >18% and is ideal for 12v systems thanks to its 20v operating voltage. In Offgridtec mono solar modules only cells of the highest quality grade are used and guarantee thanks to modern manufacturing a constant high quality and performance with maximum lifetime. Features of Offgridtec 30w 12v mono solar panel proven quality directly from Offgridtec manufactured according to the latest standards monocrystalline solar cells extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v systems on land or in mobile solar systems Frame in anodized aluminum The mono 30w 12v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtecs experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. It can withstand heavy hail and storms or extreme cold and heat without any problems and thanks to the integrated bypass diodes, the module can continue to produce power even in shaded or low light conditions. The most important technical data at a glance Power (Pmax): 30w Working voltage (Vmp): 20 V Open circuit voltage (Voc): 24 V max. current (Imp): 1.5 A Short circuit current (Isc): 1.62 A max. system voltage: 600 V permissible ambient temperature: -40°C - +85°C Dimensions: 560 x 360 x 25 mm Weight: 2,5 kg Universally applicable Offgridtecs 30w 12v Mono is universally applicable for example in 12 volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. Scope of delivery: Offgridtec 3-01-001530 30w mono 12v solar panel

The solar module 200w mono from Offgridtec (mpn 3-01-010850) with 5 busbar technology uses monocrystalline solar cells with a high efficiency of >22% and is ideally suited for 24v systems and 12v systems with mppt charge controllers thanks to its 40v operating voltage (12v systems only with mppt charge controllers that can handle the high module voltage). This constitution ensures high performance and reduced yield losses due to voltage drops. In Offgridtec mono solar modules only cells of the highest quality grade are used and guarantee thanks to modern manufacturing a constant high quality and performance with maximum lifetime. Features of Offgridtec 200 40v mono solar module Power (Pmax): 200w proven quality directly from Offgridtec high operating voltage of 40v, perfect for 24v systems with the use of a mppt charge controller can also be excellently integrated into 12v solar systems manufactured according to the latest standards monocrystalline A-grade solar cells works with 5 busbar technology extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v-24v systems on land or in mobile solar systems Proven, immediately operational solar module The mono 200w 40v is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtec's experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. Heavy hail and storms or extreme cold and heat it survives without any problems and thanks to the monocrystalline A-grade cells you can expect significant yields even on cloudy days. The most important technical data at a glance Working voltage (Vmp): 40 V Open circuit voltage (Voc): 46.6 V max. current (Imp): 5.05 A Short circuit current (Isc): 5,45 A max. system voltage: 1000 V permissible ambient temperature: -40°C - +85°C Dimensions: 1500 x 680 x 35 mm Weight: 11 Kg Part number: 3-01-010850 Universally applicable Offgridtec's 200w 40v mono is universally applicable for example in 12/24 volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as in mobile home solar systems this panel makes a good figure. Scope of delivery: Offgridtec 3-01-010850 200w mono 40v solar panel

The Offgridtec 100 w 36v delivers a power of 100 watt and is equipped with monocrystalline A-grade solar cells which deliver solid results even in poor light conditions. Ideal for 12v or 24v systems (12v only with mppt charge controllers which can handle the high module voltage). Offgridtec Solar modules are exclusively equipped with cells of the highest quality grade and guarantee thanks to modern manufacturing a constant high quality and performance with maximum service life. Main features of the Offgridtec 100w 36v (24v) mono solar module Power (Pmax): 100w proven quality directly from Offgridtec high operating voltage of 39.6v, perfect for 24v systems with the use of a mppt charge controller can also be excellently integrated into 12v solar systems manufactured according to the latest standards monocrystalline A-grade solar cells Cell structure with 5-busbars extremely resistant ESG glass makes the module usable even in the most adverse environmental conditions ideal for 12v-24v systems on land or in mobile solar systems Proven, immediately operational solar module The 100w 36v Mono is one of over 40 proven solar panels from the Offgridtec portfolio and participates in Offgridtec's experience in manufacturing high quality 12v and 24v solar cells. The module can be used in very adverse operating conditions thanks to the extremely resistant solar glass. Heavy hail and storms or extreme cold and heat it survives without problems and thanks to the monocrystalline A-grade cells you can expect significant yields even on cloudy days. The most important technical data at a glance Power (Pmax): 100 watt Voltage (Vmp): 39.6 V max. current (Imp): 2.53 A Open circuit voltage (Voc): 47.52 V Short circuit current (Isc): 2.73 A max. system voltage: 1000 V permissible ambient temperature: -40°C - +85°C Length connection cable: 90cm each Dimensions: 520 x 1050 x 35 mm Weight: 6,15 kg MC4 plug-in system Universally applicable Offgridtec's 100w 36v (24v) mono is universally applicable for example in 12/24 volt Solaranlagen on garden houses, allotments or for the power supply of lighting applications, self-sufficient systems of signal and surveillance technology and many more. But also in mobile systems such as mobile home solar systems this panel makes a good figure. Scope of delivery: 1x Offgridtec 36v (24v) 100 w solar cell, 3-01-010510

Monocrystalline 120w / 12v high-end solar panel with back-contacted high-power solar cells from the American manufacturer Sunpower - currently the best that can be processed with an efficiency of over 24%. This is where the world's best solar cells and the new back-contact process meet. The result is a high-end product at a solid price. In addition, we have taken special care in the production of this series to ensure that the rest of the module also does justice to the valuable cells. This panel is significantly lighter and smaller in area than conventional solar cells with the same output. Also, the light output in worse conditions is higher in sp series than our normal mono series.Important featuresCell efficiency of over 24 lighter and smaller than other mono modules with the same power outputMonocrystalline high power solar cells (made in USA)very good yield even in low light conditionsBack-contact (only the pure cells are visible on the front side)Black aluminum frame (black frame)Extremely durableIdeal for motorhomes, boats/yachts and small areasNoble opticsOnly monocrystalline SunPower solar cells of the highest quality are used in the production of our modules. In contrast to conventional solar modules, the cells are connected to each other on the back side (back contact), which increases the cell efficiency and ensures a noble appearance.The module has a black aluminum frame and has a specially hardened ESG solar glass.The connection cables are 80cm long and equipped with MC4 connectors. Technical DataPower(Pmax): 120wVoltage(Vmp): 19,8VMax. Current(Imp): 6,05AOpen circuit voltage(Voc): 23,35VShort circuit current(Isc): 6,41AMax. System voltage: 600 V/DCAmbient temperature: -40...+85°CDimensions: 540 x 1055 x 35 mm Weight: 7,5 kg

The fsp-2 180w is one of the newest models in the fsp-2 family and is also one of the most powerful foldable solar modules in the range. It has a 4-sided design and comes with a matching connection kit, which allows you to quickly and easily connect to the charge controller of your choice and the battery to be charged. The fsp-2 180w can be ordered in three variants. Offgridtec is also happy to customize any fsp module in terms of cable set and charging technology on request. The connection kit is stored in a lockable bag, directly on the module. So you always have a ready to use small power plant at your side. Performance that sets standards The fsp-2 180w Ultra is equipped with American spr back-contact cells from a well-known manufacturer. The cells are completely black, which gives the fsp-2 180w a very modern, high-quality look. The spr cells provide a very high efficiency of the panel and set in conjunction with the low weight and compact dimensions of the fsp-2 panel new standards in this power class. extensive range of applications: excellent usable in the camping area or for expeditions, climbing tours and much more... for vehicles and boats without fixed solar installation ... and numerous other applications in different areas... technical highlights fsp 2 180w ultra foldable solar panel Rated power: 180wp Number of sides: 4 x 45 Wp Module voltage (Vmp): 39,6 V Max. Charge current (Imp): 4,55 A Open circuit voltage (Voc): 46,6 V Short circuit current (Isc): 4,81 A Dimensions closed: 560 x 440 x 30 mm Dimensions open designed: 560 x 1970 x 6 mm Weight:6,22 kg ETFE coating SunPower high performance cells 6.0m 5mm² connection cable from fsp-2 to solar charge controller with Anderson connector on solar side 0.5m 5mm² connection cable Anderson connector to wire end sleeve (for fixed screw connection to charge controller) 1m battery connection cable solar charge controller to battery with pre-mounted tapping terminals on battery side Short-circuit-proof connection to the battery thanks to integrated flat fuse holder with 15a ato fuse the included Profi-Connection Kit The connection kit included in the scope of delivery offers everything needed for a quick start-up of the mobile solar set. Each fsp-2 has a 6.0m connection cable, which is equipped with a high-quality Anderson connector at the end. Matching to this, a second 0.5m connection cable is included, which is screwed directly to the solar input of the charge controller, and is also equipped with an Anderson connector on the other side. So you can quickly connect or disconnect the controller at any time via the Anderson connectors without having to unscrew the cables from the charge controller. For the connection of the charge controller to your battery, a 1 meter long plug & play connection cable is also included. This is screwed to the battery input of the controller and is equipped with universal crocodile clips on the battery side, which can be conveniently connected to all common battery terminals. In addition, the battery cable has a flat fuse holder with corresponding ato fuse. customizable on request All FSP-2 Ultra panels can be modified and delivered according to your specifications within a very short time. We can also flexibly adjust and adapt the cables to your needs. Just ask us! We look forward to hearing from you. Please contact customer service for any costs that may be incurred. about the fsp-2 series As with all Offgridtec solar module series, great emphasis has been placed on high quality and durability in the fsp series. The fsp 2 180w Ultra uses back-contacted solar cells like those used in our SP high performance series. These cells generate efficiencies of over 22% and are the best currently available on the market. In addition, the complete fsp-2 series is provided with an ETFE coating, which ensures better protection and at the same time guarantees a very high light transmission. Furthermore, we produce our solar modules according to current norms and standards which, together with the high-quality materials, makes our modules high-end products that deliver maximum technical performance even under the most adverse conditions. Scope of delivery 1x Offgridtec fsp-2 180w 12v, 3-01-010760 1x fsp-2 Connection Kit

Das Offgridtec OLP 10W (MPN 3-01-013100) ist ein leistungsstarkes 12V Solarmodul mit innovativem Overlapping-Design, Wafer-Bestückung und weißt Abmessungen vor, die fast in den Bereich der Hochleistungssolarmodule reichen. Die Schindel-Anordnung der Wafer sorgt für einen optimalen Stromfluss durch minimierte Leistungsverluste und einen deutlich höheren Modulwirkungsgrad durch bessere Platzausnutzung. Die verwendete PERC-Technologie verbessert die Lichtaufnahme und erhöht den Leistungsertrag. Technische Merkmale des OLP 10W Leistung (Pmax): 10Wp Spannung (Vmp): 18,7V max. Strom (Imp): 0,53A Leerlaufspannung (Voc): 22,44V Kurzschlussstrom (Isc): 0,58A max. Systemspannung: 600V Umgebungstemperatur: -40°C - +85°C Abmessungen: 244 x 300 x 25 mm Gewicht: 1,05kg Hinweis: Keine Anschlusskabel enthalten! Alleinstellungsmerkmale der OLP-Serie von Offgridtec Einzigartiges Moduldesign mit überlappender Wafer-Anordnung (Overlapping-Design) sorgt für einen sehr hohen Modulwirkungsgrad durch bessere Flächenausnutzung und reduzierte Leistungsverluste durch Leitungswiderstände Moderne, homogene Optik ohne sichtbare Leiterbahnen Innovative PERC-Technologie sorgt für verbesserte Absorption bei längeren Wellenlängen, z.B. bei flachen Einstrahlungswinkeln (frühmorgens und abends) oder bei Bewölkung Weniger Verlust bei Teilverschattung Dank Endfertigung nach Overlapping-Design hat das Modul bei einer Nennleistung von 10W einen Platzbedarf von gerade einmal 244 x 300 x 25 mm. Der Zellwirkungsgrad liegt bei über 23% Innovative PERC-Technologie Die PERC-Technologie (Passivated Emitter Rear Cell bzw. Rückseitenpassivierung) in den Offgridtec OLP Solarmodulen sorgt mit seiner Schlüsseltechnologie für einen höheren Wirkungsgrad der Solarzellen. Auf der Zellenrückseite wird zwischen der herkömmlichen Aluminium-Metallisierung und der Siliziumwafer-Schicht eine dielektrische Schicht erzeugt, die durch einen Laser mit kleinsten Löchern versehen wird. Diese dielektrische Schicht reflektiert Licht, dass ohne Erzeugung von Ladungsträgern bis zur Rückseite dringt, in die Solarzelle. Durch die Reflexion erhalten die Photonen eine "zweite Chance" Strom zu erzeugen. Neben der höheren Effizienz bei unterschiedlichen Wellenlängen und der erhöhten Wahrscheinlichkeit, dass Elektronen zur Leistung beitragen, trägt die PERC-Technologie zu niedrigeren Systemkosten und einer Steigerung des Flächenenergieertrags bei. Lieferumfang: 1x 3-01-013100 Offgridtec® OLP 10W 12V PERC Overlapping Solarpanel Schindeltechnologie

Monocrystalline 120W / 12V high-end solar panel with back-contacted high-power solar cells produced by Sunpower - a high-quality product with an efficiency of 21%. The world's best solar cells meet with the new Back-Contact process. The outcome is a high-end product at an adequate price. We made sure that the other components match the these special solar cells. This panel is lighter and has a smaller surface  than common panels with the same performance. Additionally the SP-line's light conversion rate is much higher compared to the mono-line - even during shady periods. Features: efficiency: over 20% lighter and smaller than common mono panels with the same performance monocrystalline high-power cells (made in USA) very good light-conversion rate back-Contacts: only the cells are visible on the frontside black aluminium frame very robust ideal for caravans/boats/yachts and small surfaces high-grade design For the production of these panels only high-end SunPower solar cells are used. Differing from common solar modules the cells are connected on the backside (Back-Contact) which increases the cell efficiency. The frame is made of black aluminium and hardened ESG-solarglass. The included connection cables are 80cm long and equipped with MC4-plugs. Technical data Power(Pmax): 120W Voltage(Vmp): 20,5V Max. Current(Imp): 5,87A Open circuit voltage(Voc): 24,08V Short circuit current(Isc): 6,22A Max. System voltage: 600V/DC Ambient temp.: -40...+85°C Dimensions: 415 x 1435 x 35 mm     Weight: 6,8 kg