victron bmv Smart 712 battery monitor The bmv 712 Smart from victron Energy (mpn bam030712000r) is the latest battery computer in the bmv family. It provides very precise data on parameters such as battery voltage, current, power, ampere hours consumed, state of charge and remaining runtime at the current discharge rate. The measurement resolution is very accurate and precise compared to similar products, and it is equipped with an integrated Bluetooth module that allows you to access many functions and status reports of the battery computer via a free app. Main features of the victron Smart bmv 712 battery monitor integrated Bluetooth - The Smart bmv 712 is ready for the "Internet of Things" thanks to integrated Bluetooth. In the meantime, in addition to the bmv 712, numerous other victron articles also have the integrated Bluetooth module. networking, evaluation and configuration have never been as convenient as they are today free app victronConnect - The victronConnect app enables you to evaluate and configure all victron products with vE.Direct interface. Depending on the device, numerous parameters can be evaluated directly via cell phone, computer or tablet. options for data logging and data export are also available. So you always know relatively quickly how your system is doing simplest installation - All electrical connections are made with the PCB connector on the current shunt. The shunt is connected to the Wachter via a standard rj12 telephone cable. Included: rj 12 cable (10 m) and battery cable with fuse (2 m); no other components are required. also included are a separate front bezel fu¨r a square or round display; a safety ring for rear mounting and screws for front mounting huge range of functions - Numerous battery monitoring functions and generously sized electronic components on the Smart bmv's circuit board allow you to gain deep insight into the life of your battery. In addition, the bmv allows you to detect and fix problems, even in larger battery banks, before damage occurs other features of the bmv 712 battery computer Programmable visual and audible alarm Programmable relay to disconnect insignificant loads or switch on a generator if required A 500 amp quick connect shunt and connection kit Shunt capacity selectable up to 10,000 amps vE.Direct communication port Stores a wide range of history data that can be used to evaluate usage patterns and battery condition Wide input voltage range: 6.5 - 70v High current measurement resolution 10 ma (0.01 a) Additional input for measuring voltage (of a second battery), temperature or midpoint voltage and associated alarm and relay settings high-resolution measurement data from up to 2 batteries Current ± 0.01a Voltage ± 0.01 v ampere-hour ± 0.1 ah State of charge (0 - 100%) ± 0.1% Remaining time ± 1 min Temperature (0 - 50°C or 30 - 120°F) ± 1°C/°F Accuracy of current measurement ± 0.4% low self-consumption The bmv's power consumption is only 0.7 ah per month (1 ma) at 12 v and 0.6 ah per month (0.8 ma) at 24 v. Lithium-ion batteries in particular have almost no capacity left when they are discharged to the point of shutdown due to low voltage After shutdown due to low voltage, the reserve capacity of a lithium-ion battery is approximately 1 ah per 1000 ah of battery capacity. The battery will be damaged if the remaining reserve capacity is drawn from the battery. For example, a residual current of 10 ma can damage a 200 ah battery if the system is left in a discharged state for over 8 days intelligent: Monitoring the midpoint voltage One damaged cell or battery can destroy an entire large, expensive battery bank. If batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please also refer to the bmv manual, section 5.2 for more information victron recommends the Battery Balancer (bms012201000) to maximize the life of lead-acid batteries connected in series Scope of delivery: 1x victron bmv Smart 712, battery monitor 1x shunt (included) 500 a / 50 mv 1x 10 meter 6 wire UTP cable with rj12 connectors, and cable with fuse for the '+' connection

The bmv 712 Smart from victron Energy (mpn bam030712200) is the latest battery computer in the bmv family. It provides precise data on parameters such as battery voltage, current, power, ampere hours consumed, state of charge and remaining time at the current discharge rate. The measurement resolution is very accurate and precise compared to similar products. In addition, it is equipped with an integrated Bluetooth module that allows you to access many functions and status reports of the battery computer via the free victronConnect app. Main features of the victron bmv 712 Smart battery monitor Built-in Bluetooth Module: With its built-in Bluetooth:module, the bmv Smart is already for the "Internet of Things". Meanwhile, in addition to the bmv 712, most other victron products also have integrated Bluetooth. networking, evaluation and communication has never been as convenient as it is today. Free victron Bluetooth app: The victronConnect app allows you to evaluate all victron products with vE.Direct interface. Depending on the device, numerous parameters can be read out directly via cell phone, computer or tablet. You can display all important data on one screen, adjust settings and update to the latest software. options for data logging and data export are also available. So you always know how your system is doing. Easy installation: All electrical connections are made to the current shunt using the PCB connector. The shunt is connected to the monitor via a standard RJ12 telephone cable. Included in delivery: RJ12 cable (10 m) and battery cable with fuse (2 m). No other components are required. also included is a separate front bezel for a square or round display, a safety ring for rear mounting and screws for front mounting. Huge range of functions: Numerous battery monitoring functions and generously sized electronic components on the Smart bmv's circuit board allow you to gain deep insights into the life of your battery. In addition, with the help of the bmv, you can detect and fix problems, even in larger battery banks, before damage occurs. More features of the bmv 712 battery computer Programmable visual and audible alarm Programmable relay to switch off essential loads or switch on to a generator when needed One 500 amp quick connect shunt and connection kit Shunt capacity selectable up to 10,000 amps vE.Direct communication port Stores a wide range of history data that can be used to evaluate usage patterns and battery condition Wide input voltage range: 6.5 - 70 v High current measurement resolution 10 ma (0.01a) Additional input for measuring voltage (of a second battery), temperature or midpoint voltage and associated alarm and relay settings High resolution measurement data from up to 2 batteries Current ± 0.01a Voltage ± 0.01v ampere-hour ± 0.1 ah State of charge (0-100%) ± 0.1% Remaining time ± 1 min Temperature (0-50°C or 30-120°F) ± 1°C/°F Accuracy of current measurement ±0.4% Low self consumption The current consumption of the bmv is only 0.7 ah per month (1 ma) at 12 v and 0.6 ah per month (0.8 ma) at 24 v. In particular, lithium-ion batteries have almost no capacity left when they are discharged to the point of shutdown due to low voltage. After shutdown due to low voltage, the reserve capacity of a lithium-ion battery is approximately 1 ah per 1000 ah of battery capacity. The battery will be damaged if the remaining reserve capacity is drawn from the battery. For example, a residual current of 10 ma can damage a 200 ah battery if the system is left in a discharged state for over 8 days. midpoint voltage monitoring One damaged cell or battery can destroy an entire large, expensive battery bank. When batteries are connected in series, measuring the midpoint voltage can provide a timely warning. Please also refer to the bmv manual, section 5.2 for more information. victron recommends the Battery Balancer (bms012201000) to maximize the life of lead-acid batteries connected in series. Scope of delivery: 1x victron bmv Smart 712, Battery Monitor 1x shunt 500 a / 50 mv 1x 10 meter 6 wire UTP cable with RJ12 connectors 1x 2 meter battery cable with fuse 1x front panel 1x mounting material

Battery ‘fuel gauge’, time-to-go indicator, and much moreThe remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account.Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts.Easy to installAll electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2m); no other components needed.Also included are a separate front bezel for a square or round display appearance,a securing ring for the rear mounting and screws for the front mounting.Easy to programA quick install menu and a detailed setup menu with scrolling texts assistthe user when going through the various settings. Alternatively, choose the fast and easy solution: download the smartphone app (Bluetooth Smart dongle needed)Standard features- Battery voltage, current, power, ampere- hours consumed and state of charge- Remaining time at the current rate of discharge- Programmable visual and audible alarm- Programmable relay, to turn off non critical loads or to run a generator when needed- 500 Amp quick connect shunt and connection kit- Shunt selection capability up to 10.000 Amps- VE.Direct communication port- Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health- Wide input voltage range: 9,5 – 95V- High current measurement resolution: 10 mA (0,01A)- Low current consumption: 2,9Ah per month (4mA) @12V and 2,2 Ah per month (3mA) @ 24VResolution & Accuracy (with a  500 A shunt)Current  ± 0,01 AVoltage  ± 0,01 VAmp hours  ± 0,1 AhState of charge(0-100%)  ± 0,1 %Time to go ± 1 minAccuracy of current measurement  ± 0,4 %Accuracy of voltage measurement  ± 0,3 %Standards Safety  EN 60335- 1Emission / Immunity EN 55014- 1 / EN 55014- 2Automotive  ECE R10-4 / EN 50498Accessories  Shunt (included)  500A/50 mV

Battery monitor, 12/24 V DC with large, splash proof display (IP65) and power bar. Displays remaining time and stores special battery status events. An affordable battery monitor that does exactly that: providing critical information about the status of your battery bank under all circumstances. Moreover it will warn you when your battery bank is empty. Also displays the remaining time until your battery needs to be charged and stores special battery status events.

The Mastervolt Masterlink MICC (MPN 70403105) is one of the most advanced 12V 24V battery monitors available at the moment. Moreover it is a convenient remote control for the Mass Sine Inverter series, Mass battery chargers and Mass Combi series.This device combines the following appliances: state of charge (SOC) of your battery displays system voltage, system charge or power drain displays voltage of your starter battery drained ampere-hours (power meter) battery's residual capacity remote control of Mass Sine inverters, Mass battery chargers and Mass Combi Important product features: supports 2 batteries - supply battery (displays all stats) and starter battery (displays voltage) display of voltage, amperage, ampere-hours, residual time, battery capacity in %, displays special battery events operation of inverter and battery charger clear LCD-display with green background lighting wide input voltage range of 9 - 35V DC high voltage resolution of 0.01V measures currents up to 500A Ah-capacity up to 9999A equipped with a potential-free battery alarm contact logging of all important battery events for future reference only 28mA of consumption (display off)

MasterBus integrated battery monitor, with detailed information on the status of your batteries for an optimised charging process, incl. voltage, current, remaining time and consumption capacity in percentage. With an intelligent connection system, the MasterShunt is easily connected to the DC distribution. The integrated system clock combined with command-based events custom automates the system to your needs. Example of system automation: The generator should start automatically when the batteries are almost depleted. The MasterShunt also provides a robust built-in main fuse that can safely interrupt short-circuit currents of 20 kA.

The Victron Shunt 500a - 50mV (mpn shu065150050) is required for current meters with analog or digital display instruments, because these are usually realized via a measurement, a very small voltage at a shunt. In the case of the Victron Smartshunts IP65 500a - 2000a it is 50mV. The following applies: the smaller the measuring voltage at the shunts, the smaller the effects on the remaining circuit of the system. With 50mV, this provides an excellent value. Differences to the bmv-712 battery monitor No visible or audible alarms (alarms are only visible via the VictronConnect app or a gx unit) No programmable relay IP65 protection class If you need a shunt for your display device, please refer to the manual of the respective device. Scope of delivery 1x Victron shu065150050 Smartshunt 500a - 50mV IP65

Battery monitor, 12/24 V DC with large, splash proof display (IP65) and power bar. An affordable battery monitor that does exactly that: providing critical information about the status of your battery bank under all circumstances. Moreover it will warn you when your battery bank is empty.

A Mastervolt battery monitoring panel brings an end to nasty surprises, like a sudden shortage of battery power. The Masterlink BTM-III battery monitor provides an accurate indication of the current, amperage, remaining time and remaining capacity of battery bank 1, and the current and estimated capacity of battery banks 2 and 3. The built-in microprocessor calculates the remaining capacity and stores historic data. The Masterlink BTM-III includes ten languages: English, French, German, Spanish, Italian, Dutch, Norwegian, Danish, Swedish and Finnish.