Victron Phoenix Inverter 48/800 230V VE.Direct 700W 48V

The new MultiPlus 48/800/9-16 (Victron Energy, pmp481800000) is the successor to the Multiplus Compact 48/800. This unit is an advanced device combination consisting of a powerful pure sine wave inverter, an advanced 9a battery charger utilizing adaptive charging technology, and a 16a high speed AC transfer switch. In the event of a mains fault or, if shore power or on-board generator is interrupted, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. main features of the MultiPlus 48/800/9-16 Cont. Output power at 25°c: 700w / 800w at non-linear load Victron Energy mpn: pmp481800000 for 48v system voltage integrated 9a mains charger for your batteries integrated 16a mains transfer switch USV operation possible Extensive accessories available Can be used in numerous applications, whether on land or mobile proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature) PowerControl - (Multiplus 800va 1200va only) The Multi Control remote control panel can be used to set the maximum mains or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded PowerAssist - (Multiplus 800va 1200va only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries High switch-on power This is required for switching on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools Search mode When the search mode is set to 'on', the current consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the Multi will shut down at zero load or at only light load and turn back on for a short period every two seconds. if the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low) Scope of delivery: Victron Energy pmp481800000, MultiPlus 48/800/9-16

The victron MultiPlus C 12/1200/35 (MPN CMP128010000) is a combination of 12V 700W inverter and battery charger. The integrated battery charger provides 35A which allows quick charging even for bigger batteries as long as there is a grid connection.The 12V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 16A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 700W constant output and 1400W peak current, for 12V battery voltage combination of inverter with transfer switch and 35A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron CMP128010000 Multiplus C 12/800/35 Combination of 12V 700W sine inverter and 12V 35A battery charger1x Manual  

The Quattro 48/5000/70-100/100 (MPN QUA485021010) is a combination of a 48V 4000W sine inverter, a powerful battery charger and a transfer-switch. It is equipped with 2 AC-outputs and 2 AC-inputs and therefore can be connected to 2 separate AC-sources, for example the public grid or a generator. The Quattro connects automatically to the active source. The integrated battery charger provides 70A which allows quick charging even for bigger batteries as long as there is a grid connection.The 48V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Besides those two components there is also an integrated transfer-switch that enables you to realize many grid-tied solutions.Integrating the Quattro into your system can be done via VE.Bus-port or 2 COM-port which allows nearly unlimited networking. Extremely flexible thanks to 2 AC-input and 2 AC-outputsThe main output ensures uninterrupted operation. In case of a blackout or a failure in the grid/generator the Quattro takes over the supply of connected consumers. Switching happens so fast (<20ms) that the uninterrupted supply of computers and other electronic devices is ensured.The second output only provides power if AC-power is available on one of the inputs. Consumers that must not discharge the battery - for example water boilers - can be connected to that output. Important details: 4000W constant output and 10.000W peak current, for 48V battery voltage combination of inverter with transfer switch and 70A battery charger provides pure 230V sine voltage at 50Hz 2x AC-inputs with intergerated transfer-switch / 2 x 100A max. switch-current 2x AC-outputs + 1 additional output that only works when AC-power is available on one of the AC-inputs. VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron Quattro devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed besides the VE.Bus-port Quattro devices come with 2 additional COM-ports which allow nearly unlimited system integration PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) thanks to the integrated transfer-switch with 16A or 50A usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened 3 separate relays - each programmable compatible with many Victron control- and monitoring-panels very high efficiency and low consumption Massive performance extensionUp to 6 Quattros can be connected parallely. This creates a system with 6 48/10000/140 units 54 kW/60 kVA performance or 840A charging current. Three units can be configured for three-phase operation. But that's not all: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 162 kW/180 kVA and over 2500A charging capacity. PowerControl - operation with limited generator performance, shore or grid powerThe Quattro is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The Quattro then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the Quattro to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the Quattro ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe Quattro can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, MultiControl panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Quattro. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron QUA485021010 Quattro 48/5000/70-100/100 Combination of 48V 4000W sine inverter and 48V 70A battery charger + 2 AC-inputs with integrated transfer-switch1x Manual