Safe shopping with solar experts
Fast Shipping
Top choice renowned brands
Customer service:
+49 (0) 8721 91994-00

Similar Products

VAT-exempt delivery possible*
KfW eligible
Backup system with Pylontech LiFePo4 storage and MultiPlus ii 48/3000 Victron Energy inverter 1-phase
The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us2000c 2.4kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/3000/35-32 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 125a 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. Extended use of your backup system To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each: • Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase • 5m Victron RJ45 UTP Cable With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid. To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system! The storage solution - Pylontech us2000c batteries The us2000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to state-of-the-art technology, the highest level of safety and a long service life are guaranteed, even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 3000W non-linear load power - 2400w continuous load - 6000w peak power for 48v battery voltage 32A transfer switch 35A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.
Variants from €3,126.53*
€2,899.90* €2,436.89**

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batterie...

Shipped in 2-5 days

Shipped in 2-5 days

VAT-exempt delivery possible*
KfW eligible
Backup system with Pylontech LiFePo4 storage and MultiPlus ii 48/5000 Victron Energy inverter 1-phase
The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us3000c 3.5kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/5000/70-50 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 200A 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. Extended use of your backup system To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each: • Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase • 5m Victron RJ45 UTP Cable With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid. To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system! The storage solution - Pylontech us3000c batteries The us3000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to advanced technology, the highest safety and long life are guaranteed even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 5000W non-linear load power - 4000w continuous load - 9000w peak power for 48v battery voltage 50a transfer switch 70A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.
Variants from €4,085.76*
€3,799.90* €3,193.19**

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batterie...

Shipped in 2-5 days

Shipped in 2-5 days

Addon Products

VAT-exempt delivery possible*
Solar panel support for flat roof mounting Inclination adjustable 10°-60°
With this solar module carrier from Offgridtec (MPN 8-01-012675) you can easily and quickly mount your solar module on a flat roof. The carrier has an adjustable tilt angle of 10-60°. As it is made of aluminium, it is corrosion-resistant and lightweight. A module up to max. 430W can be mounted. Modules up to 430W Angle of inclination 10-60 Long support adjustable from 38cm - 67cm Aluminium Scope of delivery: 1x solar panel support incl. screws1x assembly instruction
€42.85* €36.01**

With this solar module carrier from Offgridtec (MPN 8-01-012675) you can easily and quickly mount your solar module on a flat roof. The carrier has an...

Shipped in 1-3 days

Shipped in 1-3 days

VAT-exempt delivery possible*
Mounting kit with Biberschanz roof hooks for pitched roof mounting of solar panels 30mm - 35mm frame height
This set contains everything you need to mount solar modules with a maximum width of 1134 mm each on a roof with plain tiles. High-quality corrosion-free materials made of stainless steel and aluminum ensure safe and durable installation.The parts lists of the mounting kits are designed for mounting the modules directly next to each other. For example, if you are planning two rows with three solar modules each, you will need two kits for three modules each.Product detailsMounting kit with plain tile roof hooks for pitched roof mountingFor a module length of up to 1134 mmChoose between different solar module frame thicknesses30mm35mm40mmDeveloped for mounting in a rowfor each additional row - one additional kitModules are not included in the scope of deliveryThe set includesPlain tile roof hooks (stainless steel)Solar profile rails (aluminum)End clamps (aluminum)T-slot nuts (aluminum)End capsAll necessary screws and nuts
€100.58* €84.52**

This set contains everything you need to mount solar modules with a maximum width of 1134 mm each on a roof with plain tiles. High-quality corrosion-f...

Shipped in 2-5 days

Shipped in 2-5 days

VAT-exempt delivery possible*
Mounting kit with roof hooks 3-way adjustable (for roof tiles) for pitched roof mounting of solar panels 30mm - 35mm frame height
This set contains everything you need to attach modules with a maximum width of 1134 mm each to a tiled roof. The roof hooks included are specially designed for tiled roofs. High-quality corrosion-free materials made of stainless steel and aluminum ensure safe and durable installation.The parts lists of the mounting kits are designed for mounting the modules directly next to each other. For example, if you are planning two rows with three solar modules each, you will need two kits for three modules each.Product detailsMounting kit with roof hooks, 3-way adjustable (for roof tiles) for pitched roof mountingFor a module length of up to 1134 mmChoose between different solar module frame thicknesses30mm35mm40mmDeveloped for mounting in a rowfor each additional row - one additional kitModules are not included in the scope of deliveryThe set includesRoof hook, 3-way adjustable (stainless steel)Solar profile rails (aluminum)End clamps (aluminum)T-slot nuts (aluminum)End capsAll necessary screws and nuts
€106.95* €89.87**

This set contains everything you need to attach modules with a maximum width of 1134 mm each to a tiled roof. The roof hooks included are specially de...

Shipped in 2-5 days

Shipped in 2-5 days

VAT-exempt delivery possible*
Mounting kit with hanger bolts for pitched roof mounting of solar panels 30mm - 35mm frame height
This set contains everything you need to mount solar modules with max. 1m each on a corrugated hernite or sheet metal roof. Highest quality corrosion-free materials made of stainless steel and aluminum ensure a safe and long-lasting installation.The parts lists of the mounting kits are designed for mounting the modules directly next to each other. For example, if you plan two rows below each other with three solar modules each, you will need two kits for three modules each.Includes:Hanger bolts and adapter plate (va, stainless steel)Solar profile rails (aluminum)End clamps (aluminum)Slot nuts (aluminum)End capsAll necessary screws and nuts Notice:Only for framed modules with 30mm/35mm frame thicknessModules are not included
€87.08* €73.18**

This set contains everything you need to mount solar modules with max. 1m each on a corrugated hernite or sheet metal roof. Highest quality corrosion-...

Shipped in 1-3 days

Shipped in 1-3 days

VAT-exempt delivery possible*
Solar module holder for balcony railing suitable for modules with 30mm frame height
This set contains everything you need to attach a module to a balcony railing or other suitable railings.... The included C-hooks are specially designed for railings. This set is suitable for solar modules with a maximum width of 120mm and a frame height of 30mm.The highest quality corrosion-free stainless steel and aluminum materials ensure a safe and long-lasting installation.Set consists of:2 x 1.25m profile rail 4x4cm (aluminum)4 x C-hook pipe clamp 30-50mm4 x end clamp for solar panel (aluminum)4 x M8x30 screw (stainless steel)4 x groove stone for rail profile (aluminum)4 x end cap pa black for aluminum profiles NoteOnly for framed modules with 30mm frame thickness.Modules are not included in delivery
From €84.90* From €71.34**

This set contains everything you need to attach a module to a balcony railing or other suitable railings.... The included C-hooks are specially design...

Shipped in 1-3 days

Shipped in 1-3 days

Wattstone 6 degree concrete base for PV modules flat roof anthracite
The 6 degree concrete base from Wattstone (mpn 7001) not only offers a stable substructure for your solar modules but also maximum flexibility. Discover the ease of installation by dispensing with drilling into the roof structure and instead using the high-quality L-bricks with integrated m8 thread. With a length of 180 cm, the flat roof mounting bracket is perfect for large modules from 420w-580w for upright installation. By using the optimum tilt angle of 6 degrees, the full potential of your Solarasystem is exploited and optimum energy generation is guaranteed. The Wattstone 6 degree concrete base Substructure and ballast in one No drilling of the roof structure necessary No complicated assembly with tools Concrete base made of fine-pored exposed concrete Integrated m8 thread Quick and easy installation Technical data 2x reinforcing steel D=8mm Weight: 48kg Dimensions: 1810 x 120 x 227 mm Color: anthracite Simple assembly 6 degree tilt angle PV module Max. 5 degree angle of inclination substrate Horizontal or vertical mounting of the PV modules Underlay building protection mats No drilling of the roof structure necessary 60 cm distance between the module rows Recommended orientation east or west Horizontal fastening with module end or center clamps, stainless steel screws with spring washer recommended Traditional PV panel mounting systems usually require anchoring, bonding or ballasting to the roof. Concrete slabs are often used as ballast. With the robust concrete bases from wattstone as the basis for the surface structure, these steps are completely eliminated. The concrete base lies securely on smooth bitumen, bitumen with slate, pvc, epdm and smooth concrete, both in dry and wet conditions. You will need the following components to install a PV module: 2 wattstone concrete bases 4 matching module end clamps, each with m8 screws and washers 8 building protection mats pads, dimensions 150x150x5mm (rubber granulate carpet pad) 1 angle wrench 6mm m8 thread The integrated m8 threads are used to securely fasten PV modules. 2 threads are already cast into the concrete base for module fastening and 1 thread for optional installation of cable ducts or wind deflectors on the rear. Certification Wind tunnel tested ( din en 1991-1-4: 2021) Friction coefficient tested Scope of delivery 1x Wattstone 6 degree concrete base flat roof anthracite
€101.03*

The 6 degree concrete base from Wattstone (mpn 7001) not only offers a stable substructure for your solar modules but also maximum flexibility. Discov...

Shipped in 2-5 days

Shipped in 2-5 days

Wattstone 10 degree concrete base for PV modules flat roof natural gray
The 10 degree concrete base from Wattstone (mpn 7000n) not only offers a stable substructure for your solar modules, but also maximum flexibility. Discover the ease of installation by dispensing with drilling into the roof structure and instead using the high-quality L-bricks with integrated m8 thread. The flat roof mounting is perfect for the individual installation of one or more solar modules in any orientation. By using the optimum tilt angle of 10 degrees, the full potential of your Solarasystem is exploited and optimum energy generation is guaranteed. The Wattstone 10 degree concrete base Substructure and ballast in one No drilling of the roof structure necessary No complicated assembly with tools Concrete base made of fine-pored exposed concrete Integrated m8 thread Quick and easy installation Technical data 2x reinforcing steel D=8mm Weight: 24kg Dimensions: 800 x 120 x 227 mm Color: Natural grey Simple assembly 10 degree tilt angle PV module Max. 5 degree angle of inclination substrate Horizontal mounting of the PV modules Underlay building protection mats No drilling of the roof structure necessary 60 cm distance between the module rows Recommended orientation east or west Horizontal fastening with module end or center clamps, stainless steel screws with spring washer recommended Traditional PV panel mounting systems usually require anchoring, bonding or ballasting to the roof. Concrete slabs are often used as ballast. With the robust concrete bases from wattstone as the basis for the surface structure, these steps are completely eliminated. The concrete base lies securely on smooth bitumen, bitumen with slate, pvc, epdm and smooth concrete, both in dry and wet conditions. You will need the following components to install a PV module: 2 wattstone concrete bases 4 matching module end clamps, each with m8 screws and washers 8 building protection mats pads, dimensions 150x150x5mm (rubber granulate carpet pad) 1 angle wrench 6mm m8 thread The integrated m8 threads are used to securely fasten PV modules. 2 threads are already cast into the concrete base for module fastening and 1 thread for optional installation of cable ducts or wind deflectors on the rear. Certification Wind tunnel tested ( din en 1991-1-4: 2021) Friction coefficient tested Scope of delivery 1x Wattstone 10 degree concrete base flat roof natural gray
€82.11*

The 10 degree concrete base from Wattstone (mpn 7000n) not only offers a stable substructure for your solar modules, but also maximum flexibility. Dis...

Shipped in 2-5 days

Shipped in 2-5 days

Wattstone 15 degree concrete base for PV modules flat roof anthracite
The 15 degree concrete base from Wattstone (mpn 7002) not only offers a stable substructure for your solar modules, but also maximum flexibility. Discover the ease of installation by dispensing with drilling into the roof structure and instead using the high-quality L-bricks with integrated m8 thread. The flat roof mounting is perfect for the individual installation of one or more solar modules in any orientation. By using the optimum tilt angle of 15 degrees, the full potential of your Solarasystem is exploited and optimum energy generation is guaranteed. The Wattstone 15 degree concrete base Substructure and ballast in one No drilling of the roof structure necessary No complicated assembly with tools Concrete base made of fine-pored exposed concrete Integrated m8 thread Quick and easy installation Technical data 2x reinforcing steel D=8mm Weight: 30kg Dimensions: 1060 x 115 x 354 mm Color: anthracite Simple assembly 15 degree tilt angle PV module Max. 5 degree angle of inclination substrate Horizontal mounting of the PV modules Underlay building protection mats No drilling of the roof structure necessary 60 cm distance between the module rows Recommended orientation east or west Horizontal fastening with module end or center clamps, stainless steel screws with spring washer recommended Traditional PV panel mounting systems usually require anchoring, bonding or ballasting to the roof. Concrete slabs are often used as ballast. With the robust concrete bases from wattstone as the basis for the surface structure, these steps are completely eliminated. The concrete base lies securely on smooth bitumen, bitumen with slate, pvc, epdm and smooth concrete, both in dry and wet conditions. You will need the following components to install a PV module: 2 wattstone concrete bases 4 matching module end clamps, each with m8 screws and washers 8 building protection mats pads, dimensions 150x150x5mm (rubber granulate carpet pad) 1 angle wrench 6mm m8 thread The integrated m8 threads are used to securely fasten PV modules. 2 threads are already cast into the concrete base for module fastening and 1 thread for optional installation of cable ducts or wind deflectors on the rear. Certification Wind tunnel tested ( din en 1991-1-4: 2021) Friction coefficient tested Scope of delivery 1x Wattstone 15 degree concrete base flat roof anthracite
€94.01*

The 15 degree concrete base from Wattstone (mpn 7002) not only offers a stable substructure for your solar modules, but also maximum flexibility. Disc...

Shipped in 2-5 days

Shipped in 2-5 days

Extremely versatile complete package

The Offgridtec® HomePremium series is a true all-rounder at an unbeatable price-performance ratio. As well as being used as a usv backup solution with a choice between mains and battery priority, this PV system can also be used as a self-consumption system. There are virtually no limits to the performance of this Solarasystem - depending on personal requirements and on request, extensions are possible, both on the module and battery side. if a higher output power is required on the inverter, additional identical devices can also be connected here to increase performance.

In addition to the power electronics, the storage system and the solar modules, all components required for the connection are also included in the scope of delivery, with the exception of the solar module holder, which must be ordered separately. all other components are plug and play - this means no annoying plug installation or the like - connect and you're done. Depending on your choice, the system is supplied with or without an electricity meter.

Parts list - what's inside

For selection of electricity meter:

Extended use of your HomePremium system

The HomePremium system is supplied either with or without victron electricity meter and cable, whereby the energy meter with connection cable is required to set up an energy storage system (ess).

With this electricity meter, you can carry out a grid-parallel installation and monitor your energy consumption or control your energy costs. thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This means that seamless integration of decentralized energy sources and consumers into the existing power grid is no problem.

Luxen Solar 430w Full Black solar module

The monocrystalline and bifacial 430w Full Black Series n5 solar module fromLuxen Solarsolar module impresses with a combination of different technologies, such as N-TOPCon cell technology and a 108 half-cell layout. The smbb half-cut cell technology was also used during production to increase performance. The state-of-the-art solar module represents the pinnacle of solar technology, offering impressive power output and low LCOE.

  • Glass-glass module
  • N-TOPCon cell technology
  • smbb Half-Cut cell technology
  • Low bos & LCOE
  • Bifacial cell module technology
  • excellent anti-PID and low lid performance
  • 3 bypass diodes
  • 30-year performance guarantee and 15-year product guarantee
  • high cell efficiency of over 22%

Technical data

  • maximum power: 430w
  • Module voltage (vmp): 32.04v
  • max. current (imp): 13.42a
  • Open circuit voltage (voc): 38.96v
  • Short-circuit current (Isc): 14.13a
  • dimensions: 1722 x 1134 x 30 mm
  • Operating temperature range: -40°C to +85°C
  • Cells: 108 (6x18)
  • max. operating voltage: 1500v dc
  • Weight: 23,5kg

LiFePo4 storage technology from Pylontech

The us3000c storage battery from Pylontech is a lithium iron phosphate battery of the latest generation that offers maximum safety and service life. Each module has a battery management system (bms) for comprehensive protection against deep discharge, overcharging and damage caused by high currents or extreme temperatures. Short circuits and reverse polarity are also excluded.

Features of the Pylontech us3000c memory modules

  • Extremely cycle-proof - over 6000 cycles at 95% DoD (discharge per cycle)
  • absolutely intrinsically safe due to integrated protective shutdown (bms)
  • High charging and discharging capacity of up to 5kw per module
  • High storage density
  • Low weight and compact design
  • absolutely maintenance-free and easy to install
  • 10-year guarantee

The heart of the system - the victron MultiPlus-II 48/5000

The Multiplus-II 48/5000/70-50 from victron Energy combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100a and enables use in ess applications.

  • PowerControl and Powerassist - increasing grid or generator output
  • Built-in anti-islanding function and connection option for external current sensor (optional)
  • Can be used as a backup device in grid-connected systems
  • vE.Bus interface for parallel and three-phase operation
  • Remote monitoring and system integration
  • Parallel and three-phase operation
  • Approved according to vDE-aR-N 4105

Technical data

  • 5000 w power with non-linear load - 4000 w continuous load - 9000 w peak power
  • For 48 v battery voltage, 50 a transfer switch and 70a battery charger
  • output voltage: 230 vaC, frequency: 50 Hz
  • Max. efficiency: 95%
  • Protection class IP22

Maximum flexibility thanks to two AC outputs

The MultiPlus-II offers uninterrupted operation by automatically taking over the supply to consumers in the event of mains failures or interruptions to the shore/generator power. The switchover takes place in less than 20 milliseconds to ensure continuous operation of electronic devices. A second output supplies power only when alternating current is present at the input of the MultiPlus-II. This makes it possible to connect consumers such as a water heater that should not be discharged from the battery.

delivery is configured and matched to the components supplied

The setting options on the MultiPlus-II are extremely varied, as are its possible applications. We have already made the most important settings for you so that the system, as it is supplied, lives up to the description "plug and play" - the system is therefore ready for immediate use without any further configuration. if you order the selection with an electricity meter, we will set up the system directly as an ess.

victron Energy Cerbo gx and gx Touch 50 - the communication center of your system

The latest development in system monitoring from the company allows you to control and configure your system with ease. rounded off by the gxC Touch 50 - a waterproof 5 inch touchscreen - you always have an overview of your system parameters. The Cerbo's functions allow you to control and monitor your system perfectly, while maximizing system performance in an unprecedentedly simple way.

victron Energy has developed a new system monitor that allows you to easily control and configure your system. The gx Touch 50, a waterproof 5-inch touchscreen, provides a clear overview of your system parameters. The Cerbo module allows you to precisely monitor your system and maximize performance. It is compatible with both solar charge controllers and grid-connected inverters. Mounting material and connection cable are included in the scope of delivery. The Bluetooth function of the gx Touch 50 makes accessing your system even quicker and easier. An optional wall bracket is available.

victron Remote portal

The victron Remote Portal (vRM) is a free victron Energy Service that allows you to read out your system data remotely and configure the devices accordingly. This means that you always have full control and an overview of all relevant system parameters, even when you are away. The functionality is available online as a demo version and is ideal for getting a first impression - https://vrm.victronenergy.com/landingpage

Safety note: Only have this complete system installed and commissioned by a qualified electrician.

Offgridtec_HomePremium-M_4-01-019325_Schaltplan.pdf Download
Victron_VictronConnect_Handbuch.pdf Download
Victron_MultiPlus-II-3kVa-15kVa-230V_Datenblatt.pdf Download
Victron_Cerbo-GX_Handbuch.pdf Download
Victron_Cerbo-GX-GX-Touch_Datenblatt.pdf Download
Victron_SmartSolar-MPPT-250-60-70_Datenblatt.pdf Download
Victron_SmartSolar-MPPT-150-60-bis-250-70_Handbuch.pdf Download
Victron_MIDI-MEGA-ANL-Fuses-and-Fuse-Holders_Datasheet.pdf Download
Victron_VM3P75CT_Stromzähler_Gehäuseabmessung.pdf Download
LUXEN_430W_Bifazial_FullBlack_N5_Datasheet.pdf Download
Victron_MultiPlus-II-230V_Handbuch.pdf Download
Victron_VM3P75CT_Stromzähler_Handbuch.pdf Download
Victron_VM3P75CT_Stromzähler_Datenblatt.pdf Download
Victron_Network-Cables_CE.pdf Download
Pylontech_US_C_Datenblatt.pdf Download
Battery type: LiFePO4
Cell efficiency: 22,02%
Generator output wp: 430 Wp
Included Battery: Pylontech US3000C
Included charge controller: Victron MPPT SmartSolar 250/60
Manufacturer: Offgridtec
Module voltage (VMP): 32,04V
Open circuit voltage (VOC): 38,96V
Short circuit current (ISC): 14,13A
System voltage: 48V
max. current (IMP): 13,42A
offgridtec.com Reviews with ekomi.de
Loading products