Victron Phoenix Inverter 24/375 230V 375W VE.Direct IEC
€121.38*
€102.00**
The Victron Phoenix Inverter 24/375 (MPN: PIN241371100) converts the DC voltage of a 24-V battery system into a pure 230-V sine wave. With a continuous power output of 375 W at 25 °C and a peak power output of 600 W for up to two seconds, the inverter is suitable for smaller household and electronic devices within the specified power limits. The AC output is designed as an IEC-320 connector.
Advantages of the Victron Phoenix Inverter 24/375
- Pure sine wave with 375 W continuous power at 25 °C
- Up to 600 W peak power for two seconds
- VE.Direct connection for monitoring and configuration
- Adjustable ECO mode with 1 W power consumption in standby
- Configurable thresholds for battery voltage and restart
- Protection against short circuits, overloads, and critical operating conditions
Pure sine wave output from a 24-V battery system
The inverter provides an output voltage of 230 V AC from an input voltage of 18.4 to 34 V. The pure sine wave enables the operation of suitable electronic loads, power supplies, and small power tools. At 25 °C, 375 W is continuously available. At 40 °C, the continuous power output is 300 W. For loads with high inrush current, the inverter can provide up to 450 W for ten seconds during a cold start, as well as a peak power of 600 W for two seconds. Actual suitability must be verified based on the continuous power rating and inrush current of the connected load.
Monitoring and Configuration via VE.Direct
The VE.Direct interface allows you to monitor, among other things, battery voltage, output voltage, load, operating status, and alarm messages. In addition, the output frequency, the thresholds for undervoltage shutdown and restart, and the ECO mode settings can be adjusted. A VE.Direct USB interface (sold separately) is required to connect to a computer. A wireless connection to a smartphone or tablet requires a VE.Direct Bluetooth Smart dongle (sold separately). Bluetooth is not integrated into the inverter.
ECO Mode, Protection Functions, and Installation
In ECO mode, the inverter switches to search mode when there is no load or a very low load. At adjustable intervals, the device checks whether a sufficient load is present again and then resumes normal operation. The response threshold and search interval can be adjusted to suit the respective load. The Phoenix protects itself against output short circuits, overloads, excessively high or low battery voltage, overtemperature, excessive DC ripple voltage, and external voltage applied to the AC output. Installation must be performed by a qualified electrician. Grounding, neutral conductor routing, residual current protection, cable cross-section, and fusing must be adapted to the specific system. The AC output must not be connected to any other AC power source.
Technical Specifications
- DC system voltage: 24 V
- DC input voltage range: 18.4 to 34 V
- AC output voltage: 230 V ± 3%
- Output frequency: 50 or 60 Hz, adjustable
- Output signal: pure sine wave
- Continuous power at 25 °C: 375 W
- Continuous power at 40 °C: 300 W
- Short-term power during cold start: 450 W for 10 seconds
- Peak power: 600 W for 2 seconds
- Maximum efficiency: 88%
- Idle power: 7 W
- Charged battery detection: 28 V, adjustable
- Maximum cable cross-section at the battery connection: 10 mm²
- Recommended battery cable cross-sectional area up to 1.5 m: 4 mm²
- Recommended battery cable cross-section from 1.5 to 3 m: 6 mm²
- Protection class: IP21 when installed correctly
- Operating temperature: −40 to +65 °C
- Permissible humidity: maximum 95%, non-condensing
- Weight: 3 kg
- Dimensions: 86 × 165 × 260 mm
Package contents:
1x Victron Phoenix Inverter 24/375 230V VE.Direct IEC
1x IEC-320 plug
Manufactuerer Information
Victron Energy
Victron Energy B.V.
De Paal 35
1351 JG Almere
Netherlands
Mail: sales@victronenergy.com
Tel.: +31 365359700