Votronic Temperature Sensor

The automatic charger Pb 1225 smt 2b from Votronic (mpn 3102) is a modern battery charger for mobile use. It has charging programs for gel, agm, acid and modern lithium batteries and is designed for 12v battery voltage. The charging current at the main output is 25a. In addition, there is a secondary charge output for the starter battery, which can provide an additional 2a charge current. The device is suitable for batteries with a capacity of 100 Ah - 180 Ah. important features of the Pb 1225 smt 2b battery charger reliably charges gel, agm, acid and LiFePO4 batteries 25A charge current, 2a charge current at secondary charge output official Votronic part number: 3102 Battery capacity (recommended): 100 Ah - 180 Ah Charging options: 1 supply and 1 starter battery The charging voltage is free of peaks and regulated to prevent overcharging of the batteries Fully automatic continuous operation: the charger can be constantly connected to the battery and keeps it at full charge. In case of mains failure, the batteries are not discharged (disconnected by safety switch) Lithium LiFePO4- Maintenance, Auto Wake Up, Maintenance Phase: Regular automatic activation of the battery cell balancing every 10 days to continuously ensure the full charge of the battery Lead-acid battery regeneration twice a week during long periods of inactivity to prevent harmful acid stratification Parallel and buffer operation: in case of simultaneous consumption, the battery continues to be charged or maintained full. The charger automatically calculates and monitors the adjustment of the charging times Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short-circuit, reverse polarity, malfunction and battery back-discharge by electronic cut-off up to complete disconnection of charger and battery by built-in safety switches Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): For lead batteries (acid, gel, agm), the charging voltage is automatically adapted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and thus battery load is avoided For LiFePO4 batteries, the battery temperature sensor is required for the function: it serves the battery protection at high and especially at low temperatures below 0°c Silent Run function: Noise-optimized operation at the push of a button (night operation) Power supply function: Enables the supply of the consumers without battery (e.g. battery change) Charging cable compensation: Voltage losses on the charging cables are automatically compensated Built-in on-board power supply filter: Problem-free parallel operation with Solarasystems, wind and gasoline generators, alternators, etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -agm) battery up to 8 v, then powerful support of the battery with any consumers still switched on Disconnection of the lead-acid batteries in case of mains failure, overheating, malfunction (safety switch per charge output) Separate secondary charge output "s" for support and maintenance charging of the vehicle starter battery ¬ Overview of the charging programs of the Pb 1225 smt 2b "Gel": Charging program for gel batteries, characteristic IU1oU2oU3 Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation". "agm": charging program for agm/fleece batteries, characteristic IU1oU2oU3 Intended for charging sealed, gas-tight agm (Absorbent-Glass-Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). . "UNIVERSAL": charging program for lead-acid/wet/agm batteries, characteristic IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With medium U1 level, still provides short charge times, good charge factor and good acid mixing for open and closed, low maintenance, maintenance free standard, traction, lighting, solar and heavy duty batteries, as well as agm batteries with normal U1 level. . "LiFePO4": charging program for lithium batteries, characteristic IU1oU2oU3 Charging program adapted to lithium LiFePO4 batteries with own bms and prescribed or built-in protection circuit. A special resting maintenance automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is parked (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing. Scope of delivery: 1X Votronic 3102 Pb 1225 smt 2b battery charger 1x Instruction manual (German)

The automatic charger Pb 1240 smt 3b from Votronic (mpn 3124) is a modern battery charger for mobile use. It has charging programs for gel, agm, acid and modern lithium batteries and is designed for 12v battery voltage. The charging current at the main output is 40a. In addition, there is a secondary charging output for the starter battery, which can provide an additional 4a charging current. The device is suitable for batteries with a capacity of 75 Ah - 480 Ah. important features of the Pb 1240 smt 3b battery charger reliably charges gel, agm, acid and LiFePO4 batteries 40A charge current, 4a charge current at secondary charge output official Votronic part number: 3124 Battery capacity (recommended): 75 Ah - 480 Ah Charging options: The Pb 1240 smt 3b charges: 1 to 2 supply batteries or 1 to 2 starter batteries or 1 supply and 1 starter battery. The charging voltage is free of peaks and regulated to prevent overcharging of the batteries Fully automatic continuous operation: the charger can be constantly connected to the battery and keeps it at full charge. In case of mains failure, the batteries are not discharged (disconnected by safety switch) Lithium LiFePO4- Maintenance, Auto Wake Up, Maintenance Phase: Regular automatic activation of the battery cell balancing every 10 days to continuously ensure the full charge of the battery Lead-acid battery regeneration twice a week during long periods of inactivity to prevent harmful acid stratification Parallel and buffer operation: in case of simultaneous consumption, the battery continues to be charged or maintained full. The charger automatically calculates and monitors the adjustment of the charging times Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short-circuit, reverse polarity, malfunction and battery back-discharge by electronic cut-off up to complete disconnection of charger and battery by built-in safety switches Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): For lead batteries (acid, gel, agm), the charging voltage is automatically adapted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and thus battery load is avoided For LiFePO4 batteries, the battery temperature sensor is required for the function: it serves the battery protection at high and especially at low temperatures below 0°c Silent Run function: Noise-optimized operation at the push of a button (night operation) Power supply function: Enables the supply of the consumers without battery (e.g. battery change) Charging cable compensation: Voltage losses on the charging cables are automatically compensated Built-in on-board power supply filter: Problem-free parallel operation with Solarasystems, wind and gasoline generators, alternators, etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -agm) battery up to 8 v, then powerful support of the battery with any consumers still switched on Disconnection of the batteries in case of mains failure, overheating, malfunction (safety switch per charge output) Separate secondary charging output "s" for support and maintenance charging of the vehicle starter battery Charging current distributor optionally switchable to separate charging program for starter battery Starter battery is also charged with full charging current if required (short vehicle service life) Battery capacity can be set 4 times (total of 12 charging programs) Inputs for voltage sensor (sense) leads, optionally usable with overlong charging leads and/or external, lossy diode charging current distributors Mains/charging power can be reduced in case of low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation, etc. (power limit function) Overview of the charging programs of the Pb 1240 smt 3b "Gel": Charging program for gel batteries, characteristic IU1oU2oU3?Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation". "agm": charging program for agm/non-woven batteries, characteristic IU1oU2oU3?designed for charging sealed, gas-tight agm (Absorbent-Glass-Mat) batteries in lead-non-woven technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). . "UNIVERSAL": charging program for lead-acid/wet/agm batteries, characteristic IU1oU2oU3?universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With medium U1 level, still provides short charge times, good charge factor and good acid mixing for open and closed, low maintenance, maintenance free standard, traction, lighting, solar and heavy duty batteries, as well as agm batteries with normal U1 level. . "LiFePO4": charging program for lithium batteries, characteristic IU1oU2oU3?charging program adapted to lithium LiFePO4 batteries with own bms and prescribed or built-in protection circuit. A special resting maintenance automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is parked (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing. Scope of delivery: 1X Votronic 3124 Pb 1240 smt 3b battery charger 1x Instruction Manual (German)

The automatic charger Pb 1280 smt 2b from Votronic (mpn 3131) is a modern battery charger for mobile use. It has charging programs for gel, agm, lead-acid batteries and is designed for 12v battery voltage. The charging current at the main output is 80a. In addition, there is a secondary charging output for the starter battery, which can provide an additional 2a charging current. The device is suitable for batteries with a capacity of 150 Ah - 880 Ah. important features of the Pb 1280 smt 2b battery charger charges reliably gel, agm and lead-acid 80A charge current, 4a charge current at secondary charge output official Votronic part number: 3131 Battery capacity (recommended): 150 Ah - 880 Ah Charging capabilities: The Pb 1280 smt 2b charges: one supply battery and one starter battery. Excellent charging technology Charging voltages are free of peaks and regulated to eliminate overcharging Fully automatic continuous operation for constant readiness for use of the batteries Precise battery temperature compensation (temperature sensor part no. 2001 required) Separate auxiliary charge output "S" for support and maintenance charging of the vehicle starter battery, max. 2a Automatic battery regeneration during long idle periods (twice a week) Compensation of voltage losses on the charging cables for exact compliance with the charging voltages Intelligent microprocessor control takes into account the simultaneous co-powering of consumers on the battery Disconnection of the batteries in case of mains failure, overheating, malfunction (safety switch per charging output) Silent-run function adjustable (night setback) Battery capacity adjustable 4 times (total of 12 charging programs) Inputs for voltage sensor (sense) lines, optionally usable with overlong charging lines and/or external, lossy diode charging current distributors Mains/charging power can be reduced in case of low-power or limited mains supply, e.g. weakly fused shore power, generator operation, etc. (power limit function) overview of the charging programs of the Pb 1280 smt 2b "Gel": Charging program for gel batteries, characteristic IU1oU2oU3?Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charge voltage level and longer U1 holding times in order to achieve short charge times with particularly high capacity storage and to avoid long-term battery "starvation". "agm": charging program for agm/fleece batteries, characteristic IU1oU2oU3?Intended for charging sealed, gas-tight agm (Absorbent-Glass-Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). . "UNIVERSAL": charging program for lead-acid/wet/agm batteries, characteristic IU1oU2oU3?universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With medium U1 level, still provides short charge times, good charge factor and good acid mixing for open and closed, low maintenance, maintenance free standard, traction, lighting, solar and heavy duty batteries, as well as agm batteries with normal U1 level. . Scope of delivery: 1x Votronic 3131 Pb 1280 smt 2b battery charger 1x instruction manual (German)

Das VAC 1250 F 3A (MPN0482) von Votronic ist ein modernes Batterieladegerät und zeichnet sich durch seine kompakte Bauform, geringem Gewicht sowie volle Ladeleistung auch bei großen Abweichungen der Netzversorgung aus. Es verfügt über Ladeprogramme für GEL, AGM und Säure Batterien und ist für 24V Batteriespannung ausgelegt. Die intelligente Mikroprozessor-Ladesteuerung mit IU1oU2oU3-Ladekennlinien und dynamischer Ladezeitberechnung sorgt automatisch für die schnelle und schonende Vollladung sowie anschließende 100% Ladevollerhaltung der angeschlossenen Batterien aus jedem beliebigen Anfangsladezustand heraus. Über das VAC 1250 F 3A Batterieladegerät Batterietyp einstellbar: Gel, AGM, Säure Autom. Batterie-Regenerierung Netzteil-Funktion (Batteriewechsel) Man. Ladestart bei tiefentladener Batterie Anschluss Fern-Bedienung/-Anzeige Ladestromverteiler, schaltbar Start AC-Power-Limit-Funktion Schaltausgang Motor-Startsperre Temperatur-Kompensation Temperatur-Sensoren (2) Spannungsfühler Elektronik feuchtigkeitsgeschützt Eigenschaften Das Ladegerät gewährleistet eine Ladespannung ohne Spitzen und reguliert diese so, dass eine Überladung der Batterien ausgeschlossen ist. Es bietet einen vollautomatischen Dauerbetrieb, sodass das Ladegerät kontinuierlich mit der Batterie verbunden sein kann, um sie auf Vollladung zu halten. Im Falle eines Netzausfalls wird die Batterie durch einen Sicherheits-Schalter geschützt und nicht entladen. Das Ladegerät führt automatisch zweimal wöchentlich eine Batterie-Regenerierung während Standzeiten durch, um schädliche Säureschichtungen zu verhindern. Zusätzlich verfügt das Ladegerät über eine Netzteilfunktion, die die Versorgung der Verbraucher ohne Batterie ermöglicht, beispielsweise beim Batteriewechsel. Spannungsverluste auf den Ladekabeln werden automatisch durch die Ladekabel-Kompensation ausgeglichen. Ein eingebauter Bordnetzfilter ermöglicht einen problemlosen Parallelbetrieb mit Benzingeneratoren, Lichtmaschinen, Generatoren usw. an einer Batterie. Technische Daten Nennspannung: 24V Ladestrom: 25A Batterie-Kapazität: 40Ah - 125Ah Netz-Spannung: 230V AC Anzahl Ladeausgänge: 2 Max. Leistungsaufnahme (AC): 830W Temperaturbereich: -20 bis +45°C Maße: 330 x 139 x 74 mm Ladekennlinie: IU1oU2oU3 Gewicht: 2,4kg Schutzfaktoren Verpolschutz Kurzschlussschutz Rückentladeschutz Sicherheitsschutz Überlastschutz Lieferumfang 1x Votronic 0482 VAC 1250 F 3A Batterieladegerät

The VAC 2425 f 3a (MPN0496) from Votronicis a modern battery charger and is characterized by its compact design, low weight and full charging power even with large deviations in the mains supply. It has charging programs for gel, agm and acid batteries and is designed for 24v battery voltage. The intelligent microprocessor charging control with "iU1oU2oU3" charging characteristics and dynamic charging time calculation automatically ensures fast and gentle full charging and subsequent 100% charge retention of the connected batteries from any initial state of charge. about the VAC 2425 f 3a battery charger Adjustable battery type: gel, agm, acid Automatic battery regeneration Mains adapter function (battery change) Man. Charging start when battery is deeply discharged Remote control/display connection Charging current distributor, switchable Start AC power limit function Switching output engine start inhibit Temperature compensation Temperature sensors (2) Voltage sensor Electronics protected against moisture Features The charger ensures a charging voltage without peaks and regulates it in such a way that overcharging of the batteries is prevented. It offers fully automatic continuous operation so that the charger can be continuously connected to the battery to keep it fully charged. In the event of a mains failure, the battery is protected by a safety switch and is not discharged. The charger automatically performs a battery regeneration twice a week during downtimes to prevent harmful acid stratification. In addition, the charger has a mains adapter function, which enables consumers to be supplied without a battery, for example when changing the battery. Voltage losses on the charging cables are automatically compensated for by the charging cable compensation. A built-in on-board mains filter enables problem-free parallel operation with petrol generators, alternators, generators etc. on a battery. Technical data Rated voltage: 24v Charging current: 25A Battery capacity: 40Ah- 125Ah Mains voltage: 230v AC Number of charging outputs: 2 Max. Power consumption (ac): 830W Temperature range: -20 - +45°C Dimensions: 330 x 139 x 74mm Protection class: i / iP2X Charging characteristic: iU1oU2oU3 Weight: 2,4kg Protection factors Polarity reversal protection Short-circuit protection Reverse discharge protection Safety protection overcharge protection overload protection Scope of delivery 1x Votronic 0496 VAC 2425 f 3a battery charger