Votronic 3304 VCC 2412-25 IUoU-Li Charging Converter, 24 V to 12 V, 25 A
€316.77*
The Votronic VCC 2412-25 IUoU-Li (MPN: 3304) is a B2B charging converter designed to charge a 12-V service battery from a vehicle’s 24-V electrical system. With a charging current of up to 25 A, it is suitable for permanently installed battery systems in motorhomes, specialty vehicles, and boats. Four adjustable charging programs allow for adaptation to lead-acid, AGM, gel, and compatible LiFePO₄ batteries. Galvanic isolation electrically separates the input and output circuits from one another. An included temperature sensor supports battery monitoring and charging adjustment, while the multi-stage IU₁oU₂ charging curve enables battery charging tailored to the battery’s needs.
Votronic VCC 2412-25 IUoU-Li Charging Converter for 24-V Vehicle Electrical Systems
- 24-V-to-12-V charging converter for battery charging while driving
- Up to 25 A charging current for 12-V service batteries
- Recommended battery capacity of 50–170 Ah, usable up to 220 Ah
- Four charging programs for lead-acid, AGM, gel, and LiFePO₄ batteries
- IU₁oU₂ charging curve with initial, full, and trickle charging
- Galvanic isolation between input and output circuits
- Temperature monitoring with included 825 temperature sensor
- Parallel and buffer operation with connected 12-V loads
- Automatic activation via D+ or terminal 15
Reliable battery charging while driving
The VCC 2412-25 IUoU-Li converts the voltage of the 24-V starter circuit to charge a 12-V onboard battery. An additional alternator for the 12-V circuit is not required. The IU₁oU₂ charging curve controls the main charge, full charge, and subsequent trickle charge. The onboard battery can be charged even when loads are connected simultaneously, with the available power distributed accordingly. An adjustable power control reduces the charging power as the voltage in the starting circuit drops.
Four charging programs for different battery types
The programs Acid/AGM 1, AGM 2, Gel, and LiFePO4 can be selected using switches on the unit. The LiFePO4 program operates at a charging voltage of 14.4 V and is intended for suitable complete batteries with an integrated battery management system and protective circuitry. The selected charging program must comply with the battery manufacturer’s specifications.
Temperature Monitoring and Battery Protection
The included 825 temperature sensor measures the temperature of the service battery. For lead-acid batteries, the charging voltage is adjusted based on temperature, while for LiFePO4 batteries, the sensor is used for temperature monitoring and charging adjustment. The device features protection against overload, overheating, and reverse polarity at the output. If the device temperature becomes too high, the charging power is reduced or a safety shutdown is triggered. Reverse polarity at the input, on the other hand, can cause serious damage to the device.
Galvanic Isolation and Flexible Installation
Galvanic isolation prevents a conductive connection between the 24-V input circuit and the 12-V output circuit. Both battery circuits are connected using their own positive and negative leads, as shown in the wiring diagram. Activation is preferably performed via the D+ signal from the alternator or, alternatively, via terminal 15. Installation requires a dry, well-ventilated location protected from aggressive battery gases. Wire cross-sections, cable lengths, and fuses must be selected according to the installation instructions.
Technical Data
Input and Output
- Nominal input voltage: 24 V DC
- Input voltage range: 22–32 V
- Recommended minimum capacity of the starter battery: 50 Ah
- Maximum current draw: 18 A
- Maximum power consumption: 450 W
- Output: for 12-V lead-acid batteries and LiFePO4 batteries with a nominal voltage of 12.0–13.3 V
- Maximum charging current: 25 A
- Recommended onboard battery capacity: 50–170 Ah; can be used with batteries up to 220 Ah
- Galvanic isolation: provided
Charging Regulation and Control
- Compatible battery types: lead-acid, AGM, gel, and LiFePO4 with integrated BMS
- Charging programs: Acid/AGM 1, AGM 2, Gel, and LiFePO4
- Charging method: IU₁oU₂
- LiFePO4 charging voltage: 14.4 V
- Temperature monitoring: via temperature sensor 825
- Activation: D+ or terminal 15
- Operating modes: Parallel and buffer operation
- Cooling: Temperature-controlled fan with speed control
General Technical Specifications
- Manufacturer: Votronic
- Model: VCC 2412-25 IUoU-Li
- Manufacturer part number: 3304
- Product type: B2B buck converter
- Ambient temperature range: −20 to +45 °C
- Protection rating: IP2X
- Dimensions including mounting flanges: 270 × 139 × 74 mm
- Weight: 1,350 g
Package Contents
1 × Votronic VCC 2412-25 IUoU-Li charging converter
1 × Temperature Sensor 825
1 × Installation and Operating Instructions
Manufactuerer Information
Votronic
VOTRONIC Elektronik-Systeme GmbH
Johann-Friedrich-Diehm-Straße 2
36341 Lauterbach
Germany
Mail: info@votronic.de
Tel.: +49 6641 911730