Growatt ark-2.5h-a1 battery connection cable set for sph and SPA inverters

The Growatt sph5000tl3 bh-up hybrid inverter is a state-of-the-art solution for solar projects. With intelligent load management, a wide battery voltage range of 100-550 v and a VPP interface, it offers flexibility and efficiency. The inverter supports Solaranlagen with a total output of up to 7500 w and enables an uninterruptible power supply. With these features, the sph5000tl3 bh-up is the ideal solution for flexible and reliable Solaranlagen. about the sph5000tl3 bh-up inverter 100% three-phase asymmetrical output Intelligent power control at phase level Wide battery voltage range 100-550 v UPS function (ups) with 10ms switching time VPP interface Scalable system configuration DC/AC type ii SPD DC/AC ratio up to 1.5 Two MPP trackers (Maximum Power Point) Supports lithium and lead-acid batteries Hybrid inverter In contrast to conventional inverters, hybrid inverters offer the option of not only feeding the solar power generated into the grid, but also storing it in batteries. This means that the stored solar power can be used even when the sun is not shining. Another function of hybrid inverters is to optimize a household's electricity consumption by preferring to use the solar power generated directly in the household before it is fed into the grid. This leads to a reduction in energy costs and less dependence on expensive grid electricity. Operating modes - configurable according to system requirements Online mode Different operating modes can be set for optimum system integration of the sph inverter. When entered directly on the device, a priority mode can only be set for one time period. When using the online platform, up to three time periods can be set for the priority mode (a chargeable accessory is required to use this function). Load first:With the standard "Load first" mode, the connected loads (consumers) are supplied with energy first. As soon as the PV energy is sufficient for the load, the surplus energy is fed into the battery. If the battery is fully charged or none is connected, the remaining energy is fed into the grid. Battery first:In this mode, the inverter first fully charges the battery with the maximum possible solar power. If the PV power is not sufficient, the grid charging function can also be activated. Grid first:In this mode, the PV energy generated is fed into the grid first. The on and off time of the mode can be set here, as well as the power rate. Backup mode: If there is no longer any mains voltage at the device, e.g. due to a short-term power failure or blackout, the Growatt sph automatically switches to backup mode. This ensures that the AC output is supplied via the EPS-LOAD connection. The required energy is only supplied via the Solarasystem and the battery. If the PV system also fails, the battery secures the AC supply until it is discharged. If required, the automatic switch to this mode can also be deactivated. Maximum Power Point Tracking By using Maximum Power Point Tracking (mppt) technology, a Solarasystem can achieve the optimum yield. The MIC inverter is equipped with mppt, which adjusts the optimum ratio of voltage and current throughout the day according to the solar radiation and the module temperature of the solar modules. With its wide mppt voltage range, many solar modules can be connected, enabling efficient energy generation. This advantage is particularly evident when the sky is partly cloudy and the light intensity is constantly changing. Intelligent load management The inverter's integrated smart load control enables precise and efficient control of energy consumption. By using a potential-free contact, electrical loads can be controlled intelligently and prioritized. This function enables automatic detection of energy requirements and optimum use of the available energy. Smart load management ensures optimum distribution of energy and thus contributes to efficient use. With intelligent load control via the dry contact, the inverter is able to optimize the energy flow and ensure efficient operation of your Solarasystem. Growatt monitoring platform By using the optional accessories of the Shine series, you can use the Growatt monitoring platform. This platform is available as a smartphone app for iOS and Android as well as a web version. The Shine accessories must be purchased separately, but use of the platform is free of charge. you can configure and monitor all your Growatt products via Shine, and it also allows you to view self-consumption and track trends. The following Shine options are compatible with the sph series: ShineWiFi-X ShineLink-X Shine4G-X ShineMaster Technical data Recommended module power: up to 7500 w Max. DC voltage: 1000V Starting voltage: 120 V mppt voltage range: 120-1000 V/600 V Battery voltage range: 100~550V Max. Charge/discharge current: 25 A Continuous charging/discharging power: 5000 W AC rated power: 5000 W Max. Apparent power: 5000 VA Max. AC output power: 5000 W Max. Output current: 7.6 A Nominal AC voltage range: 230/400 v (310~476 V) AC mains frequency range: 50/60 Hz (45Hz-55Hz/55Hz-65Hz) Enclosure rating: IP65 Manufacturer's warranty: 10 years Maximum efficiency of 97.8 Dimensions: 505 x 453 x 198 mm Weight: 30 kg Scope of delivery 1x Growatt sph5000tl3 bh-up inverter

The spa 5000tl3 bh-up from Growatt is a 3-phase grid inverter that provides a state-of-the-art solution for your solar projects. With its programmable operating modes, a VPP interface and a wide battery voltage range of 100-550v, it offers efficiency and flexibility. In addition, it supports retrofits and new systems and ensures compatibility with high-voltage batteries. about the spa 5000tl3 bh-up inverter 100% three-phase unbalanced output Intelligent power control at phase level Intelligent load control via dry contact Wide battery voltage range 100-550 V UPS function, 10ms transfer VPP interface Programmable operating modes Display via led and lcd Supports lithium and lead-acid batteries Easy installation Intelligent load management The inverter's integrated smart load control enables precise and efficient control of energy consumption. By using a potential-free contact, electrical loads can be controlled intelligently and prioritized. This function enables automatic detection of energy requirements and optimum use of the available energy. Smart load management ensures optimum distribution of energy and thus contributes to efficient use. With intelligent load control via the dry contact, the inverter is able to optimize the energy flow and ensure efficient operation of your Solarasystem. Growatt monitoring platform By using the optional accessories of the Shine series, you can use the Growatt monitoring platform. This platform is available as a smartphone app for iOS and Android as well as a web version. The Shine accessories must be purchased separately, but use of the platform is free of charge. you can configure and monitor all your Growatt products via Shine, and it also allows you to view self-consumption and track trends. The following Shine options are compatible with the spa series: ShineWiFi-X ShineLink-X Shine4G-X ShineMaster Operating modes - Configurable according to system requirements Online mode Users can set a suitable priority mode in online mode according to the request while the spa is working. If the lcd and button settings are used, only one time period can be set. However, if the website settings are used, up to three time periods can be set for the priority mode Load First: With an inverter in the spa system, the energy from the inverter is optimized for the load and then the battery is charged. surplus energy is exported to the grid. Without Inverter or if the energy is low, the battery discharges first for the load and the grid supplies the energy if the battery capacity is insufficient. Battery First: When the spa series operates in this mode, the battery is charged first. This is suitable for periods of low power consumption. The switch-on and switch-off times of the mode and the end time of the battery charge level must be set. It is also possible to set a power that is lower than the maximum output power of the battery. With an inverter in the spa system, the energy from the inverter is first used for the battery, then for the load. The grid supplies the energy if the power of the inverter is not sufficient. Without Inverter or if its power is too low, the battery and the load are supplied by the mains. Grid First: If the spa series is operating in grid-first mode, the energy is fed into the grid first. Time periods can be set when the power consumption is too high. The switch-on and switch-off times of the mode and the end time of the battery charge level must be set here. A power can be set that is lower than the maximum output power of the battery. With an inverter in the spa system, the battery discharges to the load. If the sum of inverter power and battery power is greater than the load, excess energy flows into the grid. Without Inverter or if its energy is too low, the battery discharges to the load and excess energy flows into the grid. Backup mode: If the grid fails, the system switches to backup mode and AC power is output via the eps LOAD port using all the energy from the battery. Note that the maximum output power of the spa in this mode is 10,000w and the load connected to the eps LOAD port should be less than 10,000w. Note: You can only set a time period for "Battery First" and "Grid First" on the lcd. If you want to set more than this, you have to do so via the shineserver. Error mode: The spa`s intelligent control system continuously monitors and adjusts the status of the system. If the inverter detects unexpected events such as system error or machine error, the lcd display will show the error information and the led light will light up in error mode. Programming mode: Programming mode indicates that the spa system is being updated. The power supply should not be interrupted during the process. The inverter is automatically logged out when the update is complete and switches to another mode. verification mode: Before the spa operates in normal mode, it will switch to self-check mode. If everything is OK then, the system will switch to normal mode. Otherwise, the error mode will respond. Standby mode: If the system has no errors but the conditions are not met, the spa remains in standby mode. Technical data AC rated power: 5000W AC nominal voltage range: 230/400v (310-476V) Frequency range: 50/60Hz, ±5Hz Max. Output current: 7.6A Battery voltage range: 100-550v Max. Charging and discharging current: 25A IP protection class: IP65 Manufacturer's warranty: 10 years Operating temperature range: -25°C - +60°C Maximum efficiency of 97.8% Dimensions: 505 x 453 x 198 mm Weight: 28 kg Scope of delivery 1x Growatt spa 5000tl3 bh-up grid inverter

The Growatt ark 2.5h-a1 high voltage battery (mpn ark-2.5H-A1) is a LiFePO4 storage device with high cycle stability and long lifetime. The modular, stackable design allows flexible application for different scenarios and is easy to install. The battery offers excellent high load performance and is also suitable for outdoor installation with its ip65 protection. To avoid overvoltages in the system, the soft start is used.About the ark 2.5h-a1 battery:Modular, stackable battery conceptCobalt-free lithium iron phosphate (LFP)High cycle stability and long service lifeWall or floor installation possibleSoft start to protect the system from overvoltagesAutomatic wake-up in case of undervoltageProtection class ip65 for outdoor installationRemote diagnostics and firmware updateThe ark battery systemDue to the modular concept, the ark system can be used flexibly and expanded as needed. A battery tower can be set up with at least 2 and up to 10 storage modules, several towers can also be installed in one system. For operation, one BMS control element is required per tower, as well as a connection cable set to the corresponding inverter. For ground installation, one battery base per tower is also required.The ark high-voltage storage units are compatible with the min- and mod-xh, as well as the three-phase sph and SPA inverters. Depending on the inverter series, a different control unit, connection cable set, and starting number of batteries are required. The ark-XH system starts with 2, the ark-HV system again with 3 batteries.Areas of applicationFor grid-connected as well as stand-alone photovoltaic systemsEmergency power supplyUninterruptible power supplies (usv / UPS)Flexible expansionGrowatt's ark battery system offers high flexibility through its expandable configuration options, ranging from 5.12 kWh up to 25.6 kWh. Installation and expansion of the system is simple and straightforward due to its modular design and use of cables. Another innovation of the ark system is that, unlike other battery systems, no battery cabinet is required. Only a battery base is required for a stable stand.Soft start to protect the systemThe soft start mechanism is a protective feature used with the Growatt battery to protect the system from overvoltages. When the battery is started or turned on, the power supply is gradually increased to protect the system from damage that could be caused by a sudden voltage spike. This ensures smooth and safe operation of the battery system.High cycle lifeGrowatt ark battery modules are an ideal storage solution for photovoltaic systems due to their extremely high cycle life and the use of LiFePo4 cells. Regardless of whether it is a grid-tied or off-grid system, Growatt storage offers numerous advantages over traditional lead-acid batteries and other lithium technologies.Technical Data:Battery type: cobalt-free lithium iron phosphate (LiFePo4)Energy capacity: 2.56?kWhUsable capacity: 2.3?kWhRated voltage: 51.2?VOperating voltage range: 47.2-56.8?VCharge/discharge current: 25?A/0.5?CProtection class: ip65Temperature range: -10~50° CDimension: 650 x 260 x 180 mmWeight: approx. 28 kg10 years manufacturer warrantyCertificates: iec62619, ce, cec, rcm, UN38.3Scope of delivery:1x Growatt ark 2.5h-a1 2.56?kWh high-voltage battery1x battery connection set