Pylontech 5x us3000c LiFePO4 battery 17.5kWh with inverter connection cable set and battery cabinet

The us3000c (mpn us3000c) is a lithium storage system of the latest generation. The accumulator was specially developed to fully meet the high demands placed on a solar accumulator today. Maximum safety and a long service life are guaranteed even with regular deep discharge thanks to the latest technology. The latest battery of the market-leading manufacturer with now 3.5 kWh per module has again a battery management system (bms) built into each module and therefore offers a lot of security. Internally, the individual cells are thus monitored and balanced against overvoltage, overtemperature, deep discharge, etc. protected. The battery is compatible and certified with many available inverters. Features Extremely cycle resistant - over 6000 cycles at 95% DoD More usable energy content than the previous model US3000 Lifetime over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging power possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function capable of reducing the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects each installed battery cell from harmful influences over the entire life of the module and effectively prevents premature failure. Protection against: Deep discharge and overcharge overvoltage during charging excessive currents during charging and discharging over and under temperature Short circuit and reverse polarity Constant monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the desired storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) accumulator and an integrated BMS. High cycle life The extremely high cycle life of the installed LiFePo4 cells make Pylontech us3000c modules the optimal storage solution for photovoltaic systems. Regardless of whether the solar system is grid-connected or stand-alone, the Pylontech storage system offers several advantages over typical lead-acid batteries and other lithium technologies. Combine your Pylontech set according to your wishes Per selection you will receive between 2 and 8 pieces Pylontech us3000c (7 - 28 kWh). Matching the selected us3000c quantity, you can choose a battery cabinet, as well as a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is needed to connect the batteries of Pylontech with an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Rated voltage: 48V Rated capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharge) charge current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Temperature range charge: 0°C - +50°C Temperature range discharge: -10°C - +50°C Temperature range storage: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 years manufacturer warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by freight forwarding! Scope of delivery (per selection) 2 - 8 x Pylontech us3000c LiFePO4 (3.5 kWh per battery) 0 - 1 x battery cabinet 0 - 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter

The us3000c (mpn us3000c) from Pylontech is a lithium storage tank of the latest generation. The storage tank has been specially developed to fully meet the high demands placed on a solar storage tank today. Maximum safety and a long service life are guaranteed even with regular deep discharges thanks to the latest technology. The latest battery from the market-leading manufacturer, now with 3.5 kWh per module, once again has a battery management system (bms) built into each module and therefore offers a high level of safety. This means that the individual cells are monitored internally and protected against overvoltage, overtemperature, etc. in a balanced manner. The battery is compatible and certified with many available inverters. Features Extremely cycle-resistant - over 6000 cycles at 95% DoD More usable energy content than the predecessor model US3000 Service life over 10 years Absolutely intrinsically safe lithium technology Compatible with many available inverters Automatic address setting when connected in multi-groups High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Easy installation thanks to modular design Absolutely maintenance-free and durable Built-in soft-start function, which is able to reduce the current surge when the inverter is started from the battery Dual active protection at BMS level Supports WakeUp by 5-12V signal from rj45 port Pre-charge function to protect the ESS system from overvoltage function Battery management system in each module The battery management system integrated in each module protects every battery cell installed from harmful influences over the entire service life of the module and effectively prevents premature failure. Protection against: overcharging overvoltage during charging currents too high during charging and discharging over- and undertemperature Short circuit and reverse polarity Continuous monitoring of the individual cell voltages (cell balance) Modular design The system has a modular design and can be configured precisely to the required storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) battery and an integrated BMS. Long cycle life The extremely long cycle life of the LiFePo4 cells used make Pylontech us3000c modules the ideal storage solution for photovoltaic systems. Regardless of whether the solar system is a grid-connected or stand-alone system, the Pylontech storage system offers several advantages over typical lead batteries and other lithium technologies. Combine your Pylontech set according to your requirements Depending on your selection you will receive between 1 and 8 units of Pylontech us3000c (3.5 - 28 kWh). You will receive an optional battery cabinet to match the selected us3000c quantity. The set includes a battery connection cable set (Pylontech to inverter). The Pylontech battery connection cable set (mpn bw0us3000bal0002) includes 2 x 2 meter cables (plus/minus) with a cross-section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is required to connect the batteries from Pylontech to an inverter. Technical data Battery type: Lithium iron phosphate (LiFePo4) Nominal voltage: 48V Nominal capacity: 3552 Wh Usable capacity (95% DoD): 3374 Wh Discharge voltage range: 44.5 - 53.5V Charging voltage range: 52.5 - 53.5V Max. Peak (discharge) charging current: 90A Max. (discharging) charging current: 74A Recommended charge/discharge current: 37A Communication: rs485, CAN Weight: 32 kg Dimensions: 442 x 420 x 132 mm Protection class: IP20 Charging temperature range: 0°C - +50°C Discharge temperature range: -10°C - +50°C Storage temperature range: -20°C - +60°C Service life: over 10 years Cycle life: over 6000 at 95% DoD BMS / monitoring: integrated in each module Warranty: 10 year manufacturer's warranty Certification: TÜV, ce, UN38.8 Due to the classification as dangerous goods, this product will be shipped by a forwarding agent! Scope of delivery (per selection): 1 - 8 x Pylontech us3000c LiFePO4, 3.5 kWh per battery (quantity depending on selection) 0 - 1 x battery cabinet 1 x battery connection cable set Pylontech to inverter