The Victron Argo 80-2SC battery isolator (MPN ARG080202000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits.Compared to the 80-2AC this model is not equipped with current-limiting generator connection. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. Argo 80-2SC provides a max. charging current of 80A and supports 2 batteries or battery banks alternator max. current 80A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG080202000R Argo80-2SC Isolator 80A for 2 batteries1x Manual

The Victron Argo 180-3AC battery isolator (MPN ARG180301020) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. equipped with current-limiting connector for alternator energize input (generators, alternator,...) Argo 180-3AC provides a max. charging current of 180A and supports 3 batteries or battery banks alternator max. current 180A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG180301020 Argo 180-3AC Isolator 180A for 3 batteries1x Manual

The Victron Argo 140-3AC battery isolator (MPN ARG140301020R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. equipped with current-limiting connector for alternator energize input (generators, alternator,...) Argo 140-3AC  provides a max. charging current of 140A and supports 3 batteries or battery banks alternator max. current 140A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG140301020R Argo 140-3AC Isolator 140A for 3 batteries1x Manual

The Victron Argo 100-3AC battery isolator (MPN ARG100301000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. equipped with current-limiting connector for alternator energize input (generators, alternator,...) Argo 100-3AC  provides a max. charging current of 100A and supports 3 batteries or battery banks alternator max. current 100A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG100301000R Argo 100-3AC Isolator 100A for 3 batteries1x Manual

The Victron Argo 160-2AC battery isolator (MPN ARG160201020) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. equipped with current-limiting connector for alternator energize input (generators, alternator,...) Argo 160-2AC provides a max. charging current of 160A and supports 2 batteries or battery banks alternator max. current 160A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG160201020 Argo 160-2AC Isolator 160A for 2 batteries1x Manual

The Victron Argo 80-2AC battery isolator (MPN ARG080201000R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. equipped with current-limiting connector for alternator energize input (generators, alternator,...) Argo 80-2AC provides a max. charging current of 80A and supports 2 batteries or battery banks alternator max. current 80A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG080201000R Argo 80-2AC Isolator 80A for 2 batteries

The Victron Argo 120-2AC battery isolator (MPN ARG120201020R) allows the current distribution out of one energy source (e.g. alternator) to multiple battery circuits. With help of these isolators 2 or 3 separate battery circuits can be charged with only one power source. These batteries do not need to be connected which makes installation easier and reduces costs. Features: latest Schottky-diodes (hot-carrier-diodes) to keep voltage-loss at a minimum. equipped with current-limiting connector for alternator energize input (generators, alternator,...) Argo 120-2AC  provides a max. charging current of 120A and supports 2 batteries or battery banks alternator max. current 100A - supply battery can be used without discharging the starter battery Minimum voltage loss thanks to latest Schottky-diodes (hot-carrier-diodes)Thanks to latest Schottky-diodes voltage loss is reduced to a minimum - 0.3V at low currents and 0.45V at nominal current. All models out of Victron's Argo-series are equipped with a compensation-diode which slightly increases the alternator's output voltage and therefore compensates the voltage loss caused by the Schottky-diodes.This is important because if the isolator is integrated into the cabling between battery and alternator without any compensation a voltage loss occurs that leads to incomplete charging and early battery aging. Current-limiting alternator connectorSome kinds of generators need DC-voltage on their B+-pole as energize input. On one hand there is a direct connection of battery and generator, on the other hand the isolator prevents a current reflow that keeps the generator from starting.Arco-diodes (80-2AC or bigger) are equipped with a special alternator connector that allows an energize input when the generator is started. That ensures a smooth current flow between generator and battery. Delivery scope:1x Victron ARG120201020R Argo 120-2AC Isolator 120A for 2 batteries1x Manual