Victron Stromtransformator 100A:50mA for MultiPlus-II (5m) Drahtende

The Multiplus-II 12/3000/120-32 is a high-end device combination from victron Energy (mpn pmp122305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and the potential range of use to ESS applications. The inverter module delivers a whopping 3000 w at non-linear load, or 2400 w at linear continuous load. the 12 v battery charger is also very well proportioned, with 120 a charging power, and is complemented by a 32 a transfer switch that allows lightning-fast switching between aC connections. important features of the Multiplus-II 12/3000/120-32 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* Technical features 3000 w power at non-linear load 2400 w continuous load and 5500 w peak power for 12 v battery voltage, 32 a transfer switch and 120 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 12/3000/120-32. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In case of grid failure or interruption of shore/generator power, the MultiPlus-II takes over the supply of the connected loads. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp122305010 Multiplus-II 12/3000/120-32a 1x user manual

The Multiplus-II 24/5000/120-50a is a high-end device combination from victron Energy (mpn pmp242505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 24 v battery charger is also very well proportioned, with 120 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections. important features of the MultiPlus-II 24/5000/120-50 PowerControl and Powerassist -increase mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software Technical features 5000 w power at non-linear load 4000 w continuous load and 9000 w peak power for 24 v battery voltage, 50 a transfer switch and 120 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 24/5000/120-50. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In case of grid failure or interruption of shore/generator power, the MultiPlus-II takes over the supply of the connected loads. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp242505010 Multiplus-II 24/5000/120-50a 1x user manual

The Multiplus-II 48/8000/110-100 is a high-end device combination from victron Energy (mpn pmp482805000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and the potential range of use to ess applications. The inverter module delivers a whopping 8000 w at non-linear load, or 6400 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 110 a charging power, and is complemented by a 100 a transfer switch that allows lightning-fast switching between aC connections. important features of the Multiplus-II 48/8000/110-100 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 8000 w power at non-linear load 6400 w continuous load and 15000 w peak power for 48 v battery voltage, 100 a transfer switch and 110 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/8000/110-100. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482805000 Multiplus-II 48/8000/110-100a 1x user manual

The Multiplus-II 48/5000/70-50 gx is a high-end device combination from victron Energy (mpn pmp482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and expands the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 70 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections. Compared to the rest of the series, the gx variants have an integrated gx display with numerous other connection options. important features of the Multiplus-II 48/5000/70-50 gx integrated gx control unit with various communication ports PowerControl and Powerassist -increase of mains or generator power built-in anti-islanding function and connection for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 5000w power at non-linear load 4000 w continuous load and 9000 w peak power for 48 v battery voltage, 50 a transfer switch and 70 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50 gx. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. Scope of the integrated gx device A vE.Can interface This can be used to connect vE.Can devices from victron (e.g. vE.Can mppt). The port can also be reconfigured via the remote console for use with a compatible CaN-Bus Li-Ion battery. 1xUSB connection 1x Ethernet port 1x vE.Direct connection many possibilities for system expansion Settings can be changed within minutes using the vEConfigure software (requires a computer or laptop and MK3 USB interface).multiple monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482506000 Multiplus-II 48/5000/70-50 gx 230v 1x instruction manual

Der Multiplus-II 24/3000/70-32 GX ist eine High-End Gerätekombination von Victron Energy (MPN PMP242306000), die klassische Multiplus-Komponenten mit einem extrem leistungsstarken Sinuswechselrichter, ein Batterieladegerät und ein Transferschalter in einem kompakten Gehäuse zusammenführt. Dadurch werden die Funktionen PowerControl und PowerAssist auf 50 A erweitert und der potenzielle Einsatzbereich auf ESS-Anwendungen ausgedehnt. Das Wechselrichter Modul leistet bei nicht linearer Belastung satte 3000 W, bzw. 2400 W bei linearer Dauerbelastung. Auch das 24 V Batterieladegerät ist mit 70 A Ladeleistung sehr gut proportioniert und wird durch einen 32 A Transferschalter ergänzt, mit dem sich blitzschnell zwischen den AC-Anschlüssen hin- und herschalten lässt. Wichtige Leistungsmerkmale des Multiplus-II 24/3000/70-32 GX PowerControl und PowerAssist –Steigerung von Netz-oder Generator-Leistung GX LCD-Anzeige (hintergrundbeleuchtende Anzeige) BMS-Can-Anschlüsse Ethernet und WLAN Automatische unterbrechungsfreie Umschaltung kann als Backupgerät in netzgekoppelten Anlagen eingesetzt für die Stromversorgung bei Netzausfällen einsetzbar in verschiedenen ESS (Energy Storage System) Anwendungen bestens geeignet für die professionelle Seefahrt, Yachten, Fahrzeuge und landgebundene, netzferne Anwendungen VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb, Fernüberwachung und Systemintegration praktisch unbegrenzte Leistung durch Parallel-und Drei-Phasen-Betrieb kann vor Ort oder aus der Ferne mittels VEConfigure Software konfiguriert werden* Immer genug Power dank PowerControl und PowerAssist Am Multiplus-II 24/3000/70-32 GX kann ein maximaler Netz- oder Generatorstrom eingestellt werden. Der MultiPlus-II GX nimmt somit Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden der Batterie nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Netzanschluss überlastet wird (PowerControl-Funktion). Mit der Funktion PowerAssist erhält das PowerControl-Prinzip eine neue Dimension. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall kompensiert das MultiPlus-II GX zu schwache Generator-, Landstrom- bzw. Netzleistung sofort durch Energie aus der Batterie. Wird die Last reduziert, d. h. werden Verbraucher ausgeschaltet, kann die dann wieder ausreichend vorhandene Energie zum Laden der Batterien genutzt werden. Solarstrom: Wechselstrom auch bei Netzausfall Das Gerät kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es lässt sich sowohl mit Solar-Lade-Reglern als auch mit netzgebundenen Wechselrichtern verwenden. Maximale Flexibilität dank zweier Wechselstromausgänge Der Hauptausgang stellt einen unterbrechungsfreien Betrieb sicher. Im Falle eines Netzausfalls oder bei einer Unterbrechung des Land-/Generatorstroms übernimmt der MultiPlus-II GX die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet ist. Der zweite Ausgang liefert nur dann Strom, wenn am Eingang des MultiPlus-II GX Wechselstrom verfügbar ist. Verbraucher, die die Batterie nicht entladen dürfen, wie z. B. ein Wassererhitzer, können an diesen Ausgang angeschlossen werden. Viele Möglichkeiten zur Systemerweiterung Die Einstellungen lassen sich mit der VEConfigure Software binnen weniger Minuten ändern (es ist dafür ein Computer oder Laptop und ein MK3-USB-Interface notwendig).Es stehen mehrere Überwachungs- und Steuerungs-Optionen zur Verfügung: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (mit dem optionalen VE.Bus Smart Dongle), Batterie-Wächter, Digital Multi Bedien-Paneel. Remotekonfiguration und -überwachung Installieren Sie einen Cerbo GX oder ein anderes GX-Produkt, um eine Verbindung zum Internet herzustellen. Betriebsdaten können kostenlos auf unserer VRM-Website (Victron Remote Management) gespeichert und angezeigt werden. Wenn Sie mit dem Internet verbunden sind, kann aus der Ferne auf Systeme zugegriffen und Einstellungen geändert werden. Weiter GX-Optionen stehen Ihnen beispielsweise zur Verfügung: Victron Color Control GX Victron Venus GX Systemüberwachung BPP900400100 Technische Merkmale: Abmessungen: 506 x 275 x 147 mm Gewicht: 19 kg Leistung: 3000 W bei nicht linearer Belastung, 2400 W Dauerbelastung und 6000 W Spitzenleistung Ausgangsspannung: 230 VAC Frequenz: 50 Hz max. Wirkungsgrad: 95% Schutzklasse IP22 Lieferumfang: 1x Victron Multiplus-II 24/3000/70-32 GX 1x Bedienungsanleitung