The VE.Bus Smart Dongle from Victron Energy (mpn ass030537010) combines two products in one: first, it allows you to pair Victron inverters/chargers with VE.Bus port to your smartphone or tablet via Bluetooth; second, it adds voltage and temperature sensing to these devices, which is especially useful when used with the Multiplus 2, as it does not have integrated terminals for voltage and temperature sensor wiring. Use your VE.Bus products with the VictronConnect app First, it is the Bluetooth accessory for our inverters / chargers: Multis, MultiPlus, MultiPlus-II, MultiGrid, MultiGrid-II, Quattros and our Phoenix Inverter series with VE.Bus connection. After installation, use the VictronConnect app to monitor operation and run the system: Change the input current limit and switch between Off, On, and Charger Only modes Second, it adds voltage and temperature sensing to the inverters / chargers. Works with all models and is especially useful in combination with the MultiPlus-II as it has no built-in terminals for voltage and temperature sensor wiring For monitoring, the device is a good alternative in caravans, smaller yachts and motorhomes, for which the Color Control gx or Venus gx are an uneconomical or simply not wanted or because it is simply more convenient to quickly retrieve the desired information via smartphone Scope of delivery: 1x Victron Energy ass030537010 VE.Bus Smart Dongle 1x Red battery (+) connection cable with 10mm eyelet and inline fuse 1x Black battery connection cable (-) with 10mm eyelet 1x Terminal block with screw terminals 1x User manual

The minibms from Victron Energy (mpn bms400100000) is a simple and cost-effective alternative to the VE.Bus bms and can replace the VE.Bus bms in several applications. Important exceptions here are VE.Bus devices such as the Multiplus and Quattro series, because the minibms does not have its own VE.Bus port, unlike the VE.Bus bms. The minibms is designed for use with Victron Smart liFePo4 batteries with m8 round connector and has two outputs similar to the ve.bus bms. The operating voltage range is 9 - 70 VDC. Core tasks of the Victron minibms Switching off or disconnecting loads in the event of imminent undervoltage Switching off or disconnecting battery chargers in the event of imminent cell overvoltage or overtemperature "load Disconnect" (disconnect load) The "load Disconnect" output is normally high and is set to "free floating" when a cell undervoltage is imminent. Maximum current: 2A. The load Disconnect output can be used to control the following functions: remote on/off switching of a load and/or remote on/off switching of an electronic load switch (BatteryProtect) ) "Charge Disconnect" (charge disconnect) The Charge Disconnect output is normally high and will free float when a cell overvoltage or overtemperature is imminent. Maximum current: 10 mA. The Charge Disconnect output can be used to control the following functions: remote on/off switching of a charger and/or a Cyrix-li charger relay and/or a Cyrix-li-ct battery coupler The "System on/off" input The input "System on/off" controls both outputs. If it is off, both outputs are switched to "free floating". The loads and chargers are therefore switched off. The "System on/off" input has two connections: Remote l and Remote h. Between l and h, a remote on/off switch or a relay contact can be connected. Alternatively, terminal h can be connected to a battery positive terminal or l to a battery negative terminal scope of delivery: 1x Victron Energy bms400100000 minibms 1x instruction manual

The VE.Bus bms to bms 12/200 Alternator Cable from Victron Energy (mpn ass030510120) allows the charge control function of the bms 12/200 to be used in conjunction with the VE.Bus bms. The bms 12/200 will limit the charging current for the alternator to a safety value, and stop charging when an alarm occurs Scope of delivery: 1x Victron Energy ass030510120 VE.Bus bms to bms 12/200 alternator cable

The Skylla-i remote on-off cable from Victron Energy (mpn ass030550400) is used to connect a Skylla-i battery charger to a VE.Bus bms. The VE.Bus bms deactivates the Skylla-i charger when the batteries are fully charged. Scope of delivery: 1x Victron Energy ass030550400 Skylla-i remote on-off cable 1x installation manual