Safe shopping with solar experts
Fast Shipping
Top choice renowned brands
Customer service:
+49 (0) 8721 91994-00

Similar Products

VAT-exempt delivery possible*
KfW eligible
More versions available
Backup system with 3.5kWh Pylontech LiFePo4 storage and MultiPlus ii 48/5000 Victron Energy inverter 1-phase
The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us3000c 3.5kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/5000/70-50 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 200A 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. Extended use of your backup system To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each: • Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase • 5m Victron RJ45 UTP Cable With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid. To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system! The storage solution - Pylontech us3000c batteries The us3000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to advanced technology, the highest safety and long life are guaranteed even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 5000W non-linear load power - 4000w continuous load - 9000w peak power for 48v battery voltage 50a transfer switch 70A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.
€4,085.76* €3,433.41**

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batterie...

Shipped in 2-5 days

Shipped in 2-5 days

VAT-exempt delivery possible*
More versions available
Offgridtec backup kit 19.2kWh Pylontech LiFePO4 battery - Victron MultiPlus II 48/10000 3-phase inverter
The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a suitable MultiPlus-II inverter and a Cerbo GX for system monitoring from Victron Energy. This allows you to secure your energy supply even in the event of a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application for the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech US5000 4.8kWh LiFePO4 battery (4x or 6x depending on selection) 3x Victron MultiPlus-II 48/10000/140-100 230V device combination 2x Victron Lynx Distributor 1x Victron Lynx Power In 1x Victron Cerbo GX control panel 1x Victron GX Touch 50 display panel for Cerbo GX 1x 1.8m VE.Can to Can-Bus BMS type A cable 1x 3m Victron RJ45 UTP Cable 2x 0,9m Victron RJ45 UTP Cable 6x 1m Offgridtec battery cable 50mm² M8 eyelets 4x Pylontech battery connection cable set 2x Offgridtec set of 5 MEGA fuses 200A The Multiplus device combination is preconfigured to suit the Pylontech batteries. Extended use of your backup system An energy meter with connection cable is required to set up an ESS (Energy Storage System) with the backup system: Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase 5m Victron RJ45 UTP Cable With this electricity meter, you can carry out a grid-parallel installation and then monitor your energy consumption and control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for single-phase systems. This means that seamless integration of decentralised energy sources and consumers into the existing power grid is no problem. In order for an ESS to be taken into account in the pre-configuration, the meter must be purchased in advance or for the system! The storage solution - Pylontech US5000 batteries The Pylontech US5000 storage system is a lithium battery of the latest generation. It was specially developed to fulfil the high demands placed on backup storage systems. Thanks to state-of-the-art technology, maximum safety and a long service life are guaranteed even with regular deep discharges. Extremely cycle-resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charging function to protect the ESS system from overvoltage function The electronic core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of a 48V battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This expands the PowerControl and PowerAssist functions to 50A and extends the potential range of use to energy storage system applications. The Multiplus is therefore ideal for use as a backup device in grid-connected and off-grid power supply systems. 10000W power with non-linear load - 8000W continuous load - 18000W peak power for 48V battery voltage 100A transfer switch 140A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency: 95 Protection class: IP22 System monitoring with the Victron Cerbo GX and GX Toch display With the Cerbo GX communication centre, you can easily control and monitor your system. The flexible connection options maximise your system performance. Thanks to the Cerbo GX, you can control your system from anywhere. With the GX Touch 50 display, you always have an overview of all your system parameters and can make changes quickly and easily.
€15,932.91* €13,389.00**

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batterie...

Soon available again

Soon available again

VAT-exempt delivery possible*
KfW eligible
More versions available
Offgridtec Backup-Kit 3-phasig 7kWh mit Pylontech US3000C Akku Victron MultiPlus-II 48/5000
Die Backup-Systeme von Offgridtec sind ideal zur Notstromversorgung oder zur Erweiterung eines bestehenden Solarsystems geeignet. Die Systeme enthalten neben Lithium-Ionen Akkus von Pylontech, einen passenden MultiPlus-II Wechselrichter und einen Cerbo GX zur Systemüberwachung von Victron Energy. Damit kannst du deine Energieversorgung auch dann sicherstellen, wenn es zu einem Stromausfall kommt. Dank der UPS-Funktion bleibt der MultiPlus auch bei einem Netzfehler eingeschaltet und übernimmt die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet werden kann. Einsatzgebiete des Offgridtec Backup-Kits: Notstromversorgung Netzunabhängige Solarsysteme (Inselanlagen) Nachrüstung bestehender PV-Anlagen Netzgekoppelte Stromversorgung USV-Anlagen Was enthält das Offgridtec Backup-System? Pylontech US3000C 3,5kWh LiFePO4 Akku (je nach Auswahl 2x, 4x oder 6x) 3x Victron MultiPlus-II 48/5000/70-50 230V Gerätekombination 2x Victron Lynx Distributor 1x Victron Cerbo GX Bedienpanel 1x Victron GX Touch 50 Anzeigepanel für Cerbo GX 1x Victron MK3-USB Ve.Bus zu USB Interface 1x 1,8m VE.Can zu Can-Bus BMS Typ A Kabel 2x 0,9m Victron RJ45 UTP Kabel 1x 3m Victron RJ45 UTP Kabel 3x 1m Offgridtec Batteriekabel 35mm² M8-Ösen 3x 200A 70V MEGA Sicherung Pylontech Batterieanschlusskabelset (je nach Auswahl 1x oder 2x) Erweiterte Nutzung deines Backup-Systems Um ein ESS (Energy Storage System) mit dem Backup-System errichten zu können, wird jeweils ein Energiezähler mit Anschlusskabel benötigt: Victron VM-3P75CT Energy Meter 3-phasiger Stromzähler 75A/phase 5m Victron RJ45 UTP Kabel Mit diesem Stromzähler kannst du eine netzparallele Installation vornehmen und danach deinen Energieverbrauch überwachen, bzw. deine Energiekosten kontrollieren. Dank der Phasenkompensation könntest du sogar den 3-phasigen Zähler auch für 1-phasige Systeme nutzen. Damit sind nahtlose Integrationen von dezentralen Energiequellen und Verbrauchern in das bestehende Stromnetz kein Problem. Damit ein ESS in der Vorkonfiguration berücksichtigt werden kann, muss der Zähler zwingend im Vorfeld bzw. zum System erworben werden! Die Speicherlösung – Pylontech US3000C Akkus Der US3000C Speicher ist ein Lithiumakku der neuesten Generation. Er wurde speziell für die hohen Ansprüche, die an Backup-Speicher gestellt werden, zu erfüllen. Dank hochmoderner Technologie sind höchste Sicherheit und eine lange Lebensdauer auch bei regelmäßiger tiefer Entladung garantiert. Extrem zyklenfest – über 6000 Zyklen bei 95% DoD Absolut eigensichere Lithiumtechnologie Hohe Lade- und Entladeleistung möglich Integriertes BMS Sehr hohe Speicherdichte – geringes Gewicht und kompakte Bauweise Absolut wartungsfrei und langlebig Vorladefunktion zum Schutz des ESS-Systems vor Überspannungsfunktion Der Elektronik-Kern – die Victron Multiplus-II Gerätekombination Der Multiplus-II 48/5000/70-50 ist eine High-End Gerätekombination von Victron Energy (MPN PMP482505010) die klassische Multiplus-Komponenten mit einem externen Stromsensor und integrierter Anti-Islanding Funktion verbindet. Dadurch werden die Funktionen PowerControl und PowerAssist auf 100 A erweitert und der potenzielle Einsatzbereich auf ESS-Anwendungen ausgedehnt. Das Wechselrichter Modul leistet bei nicht linearer Belastung satte 5000 W, bzw. 4000 W bei linearer Dauerbelastung. Auch das 48 V Batterieladegerät ist mit 70 A Ladeleistung sehr gut proportioniert und wird durch einen 50 A Transferschalter ergänzt, mit dem sich blitzschnell zwischen den AC-Anschlüssen hin- und herschalten lässt. wichtige Leistungsmerkmale des Multiplus-II 48/5000/70-50 PowerControl und PowerAssist –Steigerung von Netz-oder Generator-Leistung eingebaute Anti-Islanding-Funktion und Anschlussmöglichkeit für externen Stromsensor (optional) kann als Backupgerät in netzgekoppelten Anlagen eingesetzt für die Stromversorgung bei Netzausfällen einsetzbar in verschiedenen ESS (Energy Storage System) Anwendungen bestens geeignet für die professionelle Seefahrt, Yachten, Fahrzeuge und landgebundene, netzferne Anwendungen VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb, Fernüberwachung und Systemintegration praktisch unbegrenzte Leistung durch Parallel-und Drei-Phasen-Betrieb kann vor Ort oder aus der Ferne mittels VEConfigure Software konfiguriert werden Immer genug Power dank PowerControl und PowerAssist Am Multiplus-II 48/5000/70-50 kann ein maximaler Netz- oder Generatorstrom eingestellt werden. Das MultiPlus-II nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden der Batterie nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Netzanschluss überlastet wird (PowerControl-Funktion). Mit der Funktion PowerAssist erhält das PowerControl-Prinzip eine neue Dimension. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall kompensiert das MultiPlus-II zu schwache Generator-, Landstrom- bzw. Netzleistung sofort durch Energie aus der Batterie. Wird die Last reduziert, d. h. werden Verbraucher ausgeschaltet, kann die dann wieder ausreichend vorhandene Energie zum Laden der Batterien genutzt werden. Maximale Flexibilität dank zweier Wechselstromausgänge Der Hauptausgang stellt einen unterbrechungsfreien Betrieb sicher. Im Falle eines Netzausfalls oder bei einer Unterbrechung des Land-/Generatorstroms übernimmt das MultiPlus-II die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet ist. Der zweite Ausgang liefert nur dann Strom, wenn am Eingang des MultiPlus-II Wechselstrom verfügbar ist. Verbraucher, die die Batterie nicht entladen dürfen, wie z. B. ein Wassererhitzer, können an diesen Ausgang angeschlossen werden. Konfiguration und Überwachung aus der Ferne Installieren Sie ein Color Control GX oder andere GX-Produkte, um sich mit dem Internet zu verbinden. Die Betriebs-Daten lassen sich auf unserer VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Sind Systeme an das Internet angeschlossen, kann auf sie aus der Ferne zugegriffen und Einstellungen können geändert werden. Die Auslieferung des MultiPlus-II erfolgt standardmäßig unkonfiguriert. Sie finden hier im Downloadbereich die Konfigurations-Anleitung für das System. Sollten Sie eine Vorkonfiguration durch uns wünschen, können wir dies gern gegen Aufpreis für Sie übernehmen. Hierzu legen Sie den oben verlinkten Artikel "Offgridtec Vorkonfiguration" beim Bestellvorgang in den Warenkorb. Der Versand kann in diesem Fall 3-5 Werktage länger in Anspruch nehmen, bis die Konfiguration durchgeführt wurde. Technische Merkmale 5000 W Leistung bei nicht linearer Belastung 4000 W Dauerbelastung und 9000 W Spitzenleistung für 48 V Batteriespannung, 50 A Transfer-Schalter und 70 A Batterieladegerät Ausgangsspannung: 230 VAC, Frequenz: 50 Hz max. Wirkungsgrad liegt bei 95%, Schutzklasse IP22 Systemüberwachung mit dem Victron Cerbo GX und GX Toch Display Mit der Cerbo GX Kommunikationszentrale können Sie Ihr System ganz einfach kontrollieren und überwachen. Die flexiblen Verbindungsmöglichkeiten maximieren Ihre Systemleistung. Die Kontrolle Ihrer Anlage ist dank des Cerbo GX ortsunabhängig möglich. Mit dem GX Touch 50 Display haben Sie alle Parameter Ihres Systems stets im Blick und können Änderungen einfach und schnell vornehmen. Sicherheitshinweis: Lassen Sie dieses Komplettsystem nur von einer Elektrofachkraft installieren und in Betrieb nehmen.
€6,286.52* €5,282.79**

Die Backup-Systeme von Offgridtec sind ideal zur Notstromversorgung oder zur Erweiterung eines bestehenden Solarsystems geeignet. Die Systeme enthalte...

Shipped in 2-5 days

Shipped in 2-5 days

Addon Products

VAT-exempt delivery possible*
More versions available
5m Victron rj45 utp cable
The Victron rj45 utp is usable with the Victron communication ports VE.Bus, ve.can, VE.Net and VE9bitRS485 and is used for networking Victron products with corresponding capabilities. It is available in various lengths from 0.3m to 30m. Below you can see a listing of all available lengths 0,3m Victron mpn ASS0300649000,9m Victron mpn ASS0300649201.8m Victron mpn ASS0300649503m Victron mpn ASS0300649805m Victron mpn ASS03006500010m Victron mpn ASS03006501015m Victron mpn ASS03006502020m Victron mpn ASS03006503025m Victron mpn ASS03006504030m Victron mpn ASS030065050
Variants from €9.10*
€17.20* €14.45**

5 Meter (€3.44* / 1 Meter)

Content: 5 Meter (€3.44* / 1 Meter)

The Victron rj45 utp is usable with the Victron communication ports VE.Bus, ve.can, VE.Net and VE9bitRS485 and is used for networking Victron products...

Shipped in 1-3 days

Shipped in 1-3 days

VAT-exempt delivery possible*
Pylontech Battery cabinet 06u for us2000c / us3000c batteries
With the Pylontech battery cabinet (mpn 06u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventilation slots allow air circulation in the cabinet. Features Pre-assembled, suitable for stand mounting Ventilation slots in the top Suitable for up to 3x us2000c Pylontech LiFePO4 batteries Or for up to 2x us3000c Pylontech LiFePO4 batteries Dimensions: 600 x 510 x 404 mm Weight: 17 kg Scope of delivery: 1x battery cabinet 06U 4x cabinet feet 2x front rails
€272.51* €229.00**

With the Pylontech battery cabinet (mpn 06u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventila...

Shipped in 1-3 days

Shipped in 1-3 days

VAT-exempt delivery possible*
Pylontech Battery cabinet 09u for us2000c / us3000c batteries
With the Pylontech battery cabinet (mpn 09u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventilation slots allow air circulation in the cabinet. Features Pre-assembled, suitable for stand mounting Ventilation slots in the top Suitable for up to 4x us2000c Pylontech LiFePO4 batteries Or for up to 3x us3000c Pylontech LiFePO4 batteries Dimensions: 600 x 510 x 538 mm Weight: 20 kg Scope of delivery: 1x battery cabinet 09U
€398.53* €334.90**

With the Pylontech battery cabinet (mpn 09u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventila...

Shipped in 2-5 days

Shipped in 2-5 days

VAT-exempt delivery possible*
Pylontech 012u battery cabinet for us2000c / us3000c batteries
With the Pylontech battery cabinet (mpn 012u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventilation slots allow air circulation in the cabinet. Features Pre-assembled, suitable for stand mounting Ventilation slots in the top Suitable for up to 6x us2000c Pylontech LiFePO4 batteries Or for up to 4x us3000c Pylontech LiFePO4 batteries Dimensions: 600 x 510 x 671 mm Weight: 23 kg Scope of delivery: 1x Battery cabinet 012U
€439.11* €369.00**

With the Pylontech battery cabinet (mpn 012u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventil...

Shipped in 1-3 days

Shipped in 1-3 days

VAT-exempt delivery possible*
Pylontech Rack cabinet 24u
With the Pylontech battery cabinet (mpn 012u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventilation slots allow air circulation in the cabinet. Features Pre-assembled, suitable for stand mounting Ventilation slots in the top Suitable for up to 6x us2000c Pylontech LiFePO4 batteries Or for up to 4x us3000c Pylontech LiFePO4 batteries Dimensions: 600 x 510 x 671 mm Weight: 23 kg Scope of delivery: 1x Battery cabinet 012U
€677.11* €569.00**

With the Pylontech battery cabinet (mpn 012u) you can safely store and accommodate Pylontech battery modules of the us2000c and us3000c series. Ventil...

Shipped in 10-14 Werktage

Shipped in 10-14 Werktage

VAT-exempt delivery possible*
Victron VM-3P75CT Energy Meter 3-phasiger Stromzähler 75A/phase
Der VM-3P75CT (MPN REL200300100) von Victron Energy ist ein 3-phasiger Stromzähler der für einen maximalen Strom von 75A pro Phase ausgelegt ist. Der Energiezähler wurde für eine einfache Integration konzipiert und funktioniert bei den meisten Systemen sofort als Netzzähler und ist somit direkt einsatzbereit. Der Energy Meter berechnet die RMS-Leistungswerte für jede Phase und überträgt sie mit einer hohen Rate über VE.Can oder Ethernet, wodurch genauere Messungen für den Stromverbrauch, den Netzimport und die Netzeinspeisung, zum Beispiel in einem ESS-System, möglich sind. Der VM-3P75CT Stromzähler kann für unterschiedliche Anwendungen verwendet werden, z.B.: Energiemessung am Verteilerkasten Erfassung von AC-Erzeugungsanlagen (z.B. PV-Wechselrichter) Leistungsmessung von Lichtmaschinen Installation des VM-3P75CT Der VM-3P75CT nutzt Stromwandler in Form von Klemmen, um den Strom präzise zu erfassen, ohne dass die Verkabelung einer bestehenden Installation geändert werden muss. Methode der Vektorregistrierung Der VM-3P75CT nutzt die Vektorregistrierungsmethode, in welcher die Vektoren der einzelnen Phasen L1, L2 und L3 summiert werden. Fernüberwachung Die Daten des VM-3P75CT werden in der Victron Connect App und auf einem GX-Gerät, wie dem Cerbo GX oder Ekrano GX angezeigt. Lieferumfang: 1x Victron REL200300100 VM-3P75CT 3-phasig Stromzähler 75A/Phase 1x Bedienungsanleitung 
€294.35* €247.35**

Der VM-3P75CT (MPN REL200300100) von Victron Energy ist ein 3-phasiger Stromzähler der für einen maximalen Strom von 75A pro Phase ausgelegt...

Shipped in 1-3 days

Shipped in 1-3 days

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure.

Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed.

Areas of application of the Offgridtec backup kit:

  • Emergency power supply
  • Off-grid solar systems (stand-alone systems)
  • Retrofitting of existing PV systems
  • Grid-connected power supply
  • UPS systems

What does the Offgridtec backup system contain?

The Multiplus device combination is pre-configured to fit the Pylontech batteries.

Extended use of your backup system

To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each:
• Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase
• 5m Victron RJ45 UTP Cable

With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid.

To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system!

The storage solution - Pylontech us2000c batteries

The us2000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to state-of-the-art technology, the highest level of safety and a long service life are guaranteed, even with regular deep discharge.

  • Extremely cycle resistant - over 6000 cycles at 95% DoD
  • Absolutely intrinsically safe lithium technology
  • High charge and discharge capacity possible
  • Integrated bms
  • Very high storage density - low weight and compact design
  • Absolutely maintenance-free and durable
  • Pre-charge function to protect the ESS system from overvoltage function

The electronics core - the Victron Multiplus-II device combination

The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems.

  • 3000W non-linear load power - 2400w continuous load - 6000w peak power
  • for 48v battery voltage
  • 32A transfer switch
  • 35A battery charger
  • Output voltage: 230 vac, frequency: 50 Hz
  • max. efficiency: 95%
  • Protection class: IP22

System monitoring with the Victron Cerbo gx and gx Toch display

Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.

Pylontech_US2000C_IEC.pdf Download
Pylontech_US2000_Bedienungsanleitung.pdf Download
Pylontech_US2000CUS3000CUP5000_CE-EMC-Cert.pdf Download
Victron_MultiPlus-II-3kVa-15kVa-230V_Datenblatt.pdf Download
Offgridtec_4-01-013720-001_Schaltplan.pdf Download
Victron_Cerbo-GX-GX-Touch_Datenblatt.pdf Download
Pylontech_US2000C_TÜV-Zertifikat.pdf Download
Victron_Cerbo-GX_Handbuch.pdf Download
Pylontech_CE DECLARATION OF CONFORMITY US+UP.pdf Download
Victron_MultiPlus-II-230V_Handbuch.pdf Download
Battery monitoring: integrated
Manufacturer: Offgridtec
Product Type: Device combination Backup Kit consisting of the main components Victron MultiPlus-II 48/3000/35-32 230V, Pylontech US2000C 2.4kWh LiFePO4.
offgridtec.com Reviews with ekomi.de
Loading products