Offgridtec Backup kit retrofit kit 4.8 kWh with Pytes E-Box 4850-c battery Victron MultiPlus ii 48/3000 3-phase

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us2000c 2.4kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/3000/35-32 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 125a 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. Extended use of your backup system To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each: • Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase • 5m Victron RJ45 UTP Cable With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid. To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system! The storage solution - Pylontech us2000c batteries The us2000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to state-of-the-art technology, the highest level of safety and a long service life are guaranteed, even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 3000W non-linear load power - 2400w continuous load - 6000w peak power for 48v battery voltage 32A transfer switch 35A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us3000c 3.5kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/5000/70-50 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 200A 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. Extended use of your backup system To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each: • Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase • 5m Victron RJ45 UTP Cable With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid. To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system! The storage solution - Pylontech us3000c batteries The us3000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to advanced technology, the highest safety and long life are guaranteed even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 5000W non-linear load power - 4000w continuous load - 9000w peak power for 48v battery voltage 50a transfer switch 70A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a suitable MultiPlus-II inverter and a Cerbo GX for system monitoring from Victron Energy. This allows you to secure your energy supply even in the event of a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application for the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech US5000 4.8kWh LiFePO4 battery (4x or 6x depending on selection) 3x Victron MultiPlus-II 48/10000/140-100 230V device combination 2x Victron Lynx Distributor 1x Victron Lynx Power In 1x Victron Cerbo GX control panel 1x Victron GX Touch 50 display panel for Cerbo GX 1x 1.8m VE.Can to Can-Bus BMS type A cable 1x 3m Victron RJ45 UTP Cable 2x 0,9m Victron RJ45 UTP Cable 6x 1m Offgridtec battery cable 50mm² M8 eyelets 4x Pylontech battery connection cable set 2x Offgridtec set of 5 MEGA fuses 200A The Multiplus device combination is preconfigured to suit the Pylontech batteries. Extended use of your backup system An energy meter with connection cable is required to set up an ESS (Energy Storage System) with the backup system: Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase 5m Victron RJ45 UTP Cable With this electricity meter, you can carry out a grid-parallel installation and then monitor your energy consumption and control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for single-phase systems. This means that seamless integration of decentralised energy sources and consumers into the existing power grid is no problem. In order for an ESS to be taken into account in the pre-configuration, the meter must be purchased in advance or for the system! The storage solution - Pylontech US5000 batteries The Pylontech US5000 storage system is a lithium battery of the latest generation. It was specially developed to fulfil the high demands placed on backup storage systems. Thanks to state-of-the-art technology, maximum safety and a long service life are guaranteed even with regular deep discharges. Extremely cycle-resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charging and discharging capacity possible Integrated BMS Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charging function to protect the ESS system from overvoltage function The electronic core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of a 48V battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This expands the PowerControl and PowerAssist functions to 50A and extends the potential range of use to energy storage system applications. The Multiplus is therefore ideal for use as a backup device in grid-connected and off-grid power supply systems. 10000W power with non-linear load - 8000W continuous load - 18000W peak power for 48V battery voltage 100A transfer switch 140A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency: 95 Protection class: IP22 System monitoring with the Victron Cerbo GX and GX Toch display With the Cerbo GX communication centre, you can easily control and monitor your system. The flexible connection options maximise your system performance. Thanks to the Cerbo GX, you can control your system from anywhere. With the GX Touch 50 display, you always have an overview of all your system parameters and can make changes quickly and easily.

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us2000c 2.4kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/3000/35-32 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 125a 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. The storage solution - Pylontech us2000c batteries The us2000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to state-of-the-art technology, the highest level of safety and a long service life are guaranteed, even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 3000W non-linear load power - 2400w continuous load - 6000w peak power for 48v battery voltage 32A transfer switch 35A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontecha suitable MultiPlus-II invertera and a Cerbo gx for system monitoring from Victron Energy. This allows you to secure your energy supply even in the event of a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a power failure and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application for the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting existing PV systems Grid-connected power supply UPS systems What does the 3-phase Offgridtec backup system contain? Pylontech us2000c 2.4kWh LiFePO4 battery (2x or 4x depending on selection) 3x Victron MultiPlus-II 48/3000/35-32 230v device combination 2x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x Victron mk3-usb Ve.Bus to usb Interface 1x 1.8m VE.Can to Can-Bus bms type A cable 2x 0.9m Victron rj45 utp cable 1x 3m Victron rj45 utp cable 3x 1m Offgridtec Battery cable 35mm² M8 eyelets 3x 125A 70v mega fuse Pylontech Battery connection cable set (depending on selection 1x or 2x) Extended use of your backup system To set up an ess (Energy Storage System) with the backup system, an energy meter with connection cable is required: Victron vm-3p75ct Energy Meter 3-phase electricity meter 75A/phase 5m Victron rj45 utp cable With this electricity meter, you can carry out a grid-parallel installation and then monitor your energy consumption and control your energy costs. Thanks to phase compensation, you can even use the 3-phase meter for 1-phase systems. This means that seamless integration of decentralized energy sources and consumers into the existing power grid is no problem. In order for an ess to be included in the pre-configuration, the meter must be purchased in advance or for the system! The storage solution - Pylontech us2000c batteries The us2000c storage system is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage systems. Thanks to state-of-the-art technology, maximum safety and a long service life are guaranteed even with regular deep discharges. Extremely cycle-resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charging and discharging capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ess system from overvoltage The electronic core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of a 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-island function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus is therefore ideal for use as a backup device in grid-connected and off-grid power supply systems. 3000W power with non-linear load - 2400w continuous load - 6000w peak power for 48v battery voltage 32A transfer switch 35A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95 Protection class: IP22 Configuration The MultiPlus-II is delivered unconfigured as standard. You can find the configuration instructions for the system here in the download area. If you would like us to pre-configure the system for you, we can do this for you for an additional charge. To do this, add the article linked above "Offgridtec Pre-configuration" to the shopping cart during the ordering process. In this case, shipping may take 3-5 working days longer until the configuration has been completed. System monitoring with the Victron Cerbo gx and gx Toch display With the Cerbo gx communication center, you can easily control and monitor your system. The flexible connection options maximize your system performance. Thanks to the Cerbo gx, you can control your system from anywhere. With the gx Touch 50 display, you always have an overview of all your system parameters and can make changes quickly and easily. Safety note: Only have this complete system installed and commissioned by a qualified electrician.

Die Backup-Systeme von Offgridtec sind ideal zur Notstromversorgung oder zur Erweiterung eines bestehenden Solarsystems geeignet. Die Systeme enthalten neben Lithium-Ionen Akkus von Pylontech, einen passenden MultiPlus-II Wechselrichter und einen Cerbo GX zur Systemüberwachung von Victron Energy. Damit kannst du deine Energieversorgung auch dann sicherstellen, wenn es zu einem Stromausfall kommt. Dank der UPS-Funktion bleibt der MultiPlus auch bei einem Netzfehler eingeschaltet und übernimmt die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet werden kann. Einsatzgebiete des Offgridtec Backup-Kits: Notstromversorgung Netzunabhängige Solarsysteme (Inselanlagen) Nachrüstung bestehender PV-Anlagen Netzgekoppelte Stromversorgung USV-Anlagen Was enthält das Offgridtec Backup-System? Pylontech US3000C 3,5kWh LiFePO4 Akku (je nach Auswahl 2x, 4x oder 6x) 3x Victron MultiPlus-II 48/5000/70-50 230V Gerätekombination 2x Victron Lynx Distributor 1x Victron Cerbo GX Bedienpanel 1x Victron GX Touch 50 Anzeigepanel für Cerbo GX 1x Victron MK3-USB Ve.Bus zu USB Interface 1x 1,8m VE.Can zu Can-Bus BMS Typ A Kabel 2x 0,9m Victron RJ45 UTP Kabel 1x 3m Victron RJ45 UTP Kabel 3x 1m Offgridtec Batteriekabel 35mm² M8-Ösen 3x 200A 70V MEGA Sicherung Pylontech Batterieanschlusskabelset (je nach Auswahl 1x oder 2x) Erweiterte Nutzung deines Backup-Systems Um ein ESS (Energy Storage System) mit dem Backup-System errichten zu können, wird jeweils ein Energiezähler mit Anschlusskabel benötigt: Victron VM-3P75CT Energy Meter 3-phasiger Stromzähler 75A/phase 5m Victron RJ45 UTP Kabel Mit diesem Stromzähler kannst du eine netzparallele Installation vornehmen und danach deinen Energieverbrauch überwachen, bzw. deine Energiekosten kontrollieren. Dank der Phasenkompensation könntest du sogar den 3-phasigen Zähler auch für 1-phasige Systeme nutzen. Damit sind nahtlose Integrationen von dezentralen Energiequellen und Verbrauchern in das bestehende Stromnetz kein Problem. Damit ein ESS in der Vorkonfiguration berücksichtigt werden kann, muss der Zähler zwingend im Vorfeld bzw. zum System erworben werden! Die Speicherlösung – Pylontech US3000C Akkus Der US3000C Speicher ist ein Lithiumakku der neuesten Generation. Er wurde speziell für die hohen Ansprüche, die an Backup-Speicher gestellt werden, zu erfüllen. Dank hochmoderner Technologie sind höchste Sicherheit und eine lange Lebensdauer auch bei regelmäßiger tiefer Entladung garantiert. Extrem zyklenfest – über 6000 Zyklen bei 95% DoD Absolut eigensichere Lithiumtechnologie Hohe Lade- und Entladeleistung möglich Integriertes BMS Sehr hohe Speicherdichte – geringes Gewicht und kompakte Bauweise Absolut wartungsfrei und langlebig Vorladefunktion zum Schutz des ESS-Systems vor Überspannungsfunktion Der Elektronik-Kern – die Victron Multiplus-II Gerätekombination Der Multiplus-II 48/5000/70-50 ist eine High-End Gerätekombination von Victron Energy (MPN PMP482505010) die klassische Multiplus-Komponenten mit einem externen Stromsensor und integrierter Anti-Islanding Funktion verbindet. Dadurch werden die Funktionen PowerControl und PowerAssist auf 100 A erweitert und der potenzielle Einsatzbereich auf ESS-Anwendungen ausgedehnt. Das Wechselrichter Modul leistet bei nicht linearer Belastung satte 5000 W, bzw. 4000 W bei linearer Dauerbelastung. Auch das 48 V Batterieladegerät ist mit 70 A Ladeleistung sehr gut proportioniert und wird durch einen 50 A Transferschalter ergänzt, mit dem sich blitzschnell zwischen den AC-Anschlüssen hin- und herschalten lässt. wichtige Leistungsmerkmale des Multiplus-II 48/5000/70-50 PowerControl und PowerAssist –Steigerung von Netz-oder Generator-Leistung eingebaute Anti-Islanding-Funktion und Anschlussmöglichkeit für externen Stromsensor (optional) kann als Backupgerät in netzgekoppelten Anlagen eingesetzt für die Stromversorgung bei Netzausfällen einsetzbar in verschiedenen ESS (Energy Storage System) Anwendungen bestens geeignet für die professionelle Seefahrt, Yachten, Fahrzeuge und landgebundene, netzferne Anwendungen VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb, Fernüberwachung und Systemintegration praktisch unbegrenzte Leistung durch Parallel-und Drei-Phasen-Betrieb kann vor Ort oder aus der Ferne mittels VEConfigure Software konfiguriert werden Immer genug Power dank PowerControl und PowerAssist Am Multiplus-II 48/5000/70-50 kann ein maximaler Netz- oder Generatorstrom eingestellt werden. Das MultiPlus-II nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden der Batterie nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Netzanschluss überlastet wird (PowerControl-Funktion). Mit der Funktion PowerAssist erhält das PowerControl-Prinzip eine neue Dimension. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall kompensiert das MultiPlus-II zu schwache Generator-, Landstrom- bzw. Netzleistung sofort durch Energie aus der Batterie. Wird die Last reduziert, d. h. werden Verbraucher ausgeschaltet, kann die dann wieder ausreichend vorhandene Energie zum Laden der Batterien genutzt werden. Maximale Flexibilität dank zweier Wechselstromausgänge Der Hauptausgang stellt einen unterbrechungsfreien Betrieb sicher. Im Falle eines Netzausfalls oder bei einer Unterbrechung des Land-/Generatorstroms übernimmt das MultiPlus-II die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet ist. Der zweite Ausgang liefert nur dann Strom, wenn am Eingang des MultiPlus-II Wechselstrom verfügbar ist. Verbraucher, die die Batterie nicht entladen dürfen, wie z. B. ein Wassererhitzer, können an diesen Ausgang angeschlossen werden. Konfiguration und Überwachung aus der Ferne Installieren Sie ein Color Control GX oder andere GX-Produkte, um sich mit dem Internet zu verbinden. Die Betriebs-Daten lassen sich auf unserer VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Sind Systeme an das Internet angeschlossen, kann auf sie aus der Ferne zugegriffen und Einstellungen können geändert werden. Die Auslieferung des MultiPlus-II erfolgt standardmäßig unkonfiguriert. Sie finden hier im Downloadbereich die Konfigurations-Anleitung für das System. Sollten Sie eine Vorkonfiguration durch uns wünschen, können wir dies gern gegen Aufpreis für Sie übernehmen. Hierzu legen Sie den oben verlinkten Artikel "Offgridtec Vorkonfiguration" beim Bestellvorgang in den Warenkorb. Der Versand kann in diesem Fall 3-5 Werktage länger in Anspruch nehmen, bis die Konfiguration durchgeführt wurde. Technische Merkmale 5000 W Leistung bei nicht linearer Belastung 4000 W Dauerbelastung und 9000 W Spitzenleistung für 48 V Batteriespannung, 50 A Transfer-Schalter und 70 A Batterieladegerät Ausgangsspannung: 230 VAC, Frequenz: 50 Hz max. Wirkungsgrad liegt bei 95%, Schutzklasse IP22 Systemüberwachung mit dem Victron Cerbo GX und GX Toch Display Mit der Cerbo GX Kommunikationszentrale können Sie Ihr System ganz einfach kontrollieren und überwachen. Die flexiblen Verbindungsmöglichkeiten maximieren Ihre Systemleistung. Die Kontrolle Ihrer Anlage ist dank des Cerbo GX ortsunabhängig möglich. Mit dem GX Touch 50 Display haben Sie alle Parameter Ihres Systems stets im Blick und können Änderungen einfach und schnell vornehmen. Sicherheitshinweis: Lassen Sie dieses Komplettsystem nur von einer Elektrofachkraft installieren und in Betrieb nehmen.

Die Backup-Systeme von Offgridtec sind ideal zur Notstromversorgung oder zur Erweiterung eines bestehenden Solarsystems geeignet. Die Systeme enthalten neben Lithium-Ionen Akkus von Pylontech, einen passenden MultiPlus-II Wechselrichter und einen Cerbo GX zur Systemüberwachung. Damit kannst du deine Energieversorgung auch dann sicherstellen, wenn es zu einem Stromausfall kommt. Dank der UPS-Funktion bleibt der MultiPlus auch bei einem Netzfehler eingeschaltet und übernimmt die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet werden kann. Einsatzgebiete des Offgridtec Backup-Kits: Notstromversorgung Netzunabhängige Solarsysteme (Inselanlagen) Nachrüstung bestehender PV-Anlagen Netzgekoppelte Stromversorgung USV-Anlagen Was enthält das Offgridtec Backup-System? Pylontech US5000C 3,5kWh LiFePO4 Akku (je nach Auswahl 4x, 6x oder 8x) 3x MultiPlus-II 48/8000/110-100/100 230V Gerätekombination 2x Victron Lynx Distributor 1x Victron Cerbo GX Bedienpanel 1x Victron GX Touch 50 Anzeigepanel für Cerbo GX 1x Victron MK3-USB Ve.Bus zu USB Interface 1x 1,8m VE.Can zu Can-Bus BMS Typ A Kabel 2x 0,9m Victron RJ45 UTP Kabel 1x 3m Victron RJ45 UTP Kabel 6x 1m Offgridtec Batteriekabel 35mm² M8-Ösen 6x 200A 70V MEGA Sicherung 2x Pylontech Batterieanschlusskabelset  Erweiterte Nutzung deines Backup-Systems Um ein ESS (Energy Storage System) mit dem Backup-System errichten zu können, wird jeweils ein Energiezähler mit Anschlusskabel benötigt: Victron VM-3P75CT Energy Meter 3-phasiger Stromzähler 75A/phase 5m Victron RJ45 UTP Kabel Mit diesem Stromzähler kannst du eine netzparallele Installation vornehmen und danach deinen Energieverbrauch überwachen, bzw. deine Energiekosten kontrollieren. Dank der Phasenkompensation könntest du sogar den 3-phasigen Zähler auch für 1-phasige Systeme nutzen. Damit sind nahtlose Integrationen von dezentralen Energiequellen und Verbrauchern in das bestehende Stromnetz kein Problem. Damit ein ESS in der Vorkonfiguration berücksichtigt werden kann, muss der Zähler zwingend im Vorfeld bzw. zum System erworben werden! Die Speicherlösung – Pylontech US5000C Akkus Der US3000C Speicher ist ein Lithiumakku der neuesten Generation. Er wurde speziell für die hohen Ansprüche, die an Backup-Speicher gestellt werden, zu erfüllen. Dank hochmoderner Technologie sind höchste Sicherheit und eine lange Lebensdauer auch bei regelmäßiger tiefer Entladung garantiert. Extrem zyklenfest – über 6000 Zyklen bei 95% DoD Absolut eigensichere Lithiumtechnologie Hohe Lade- und Entladeleistung möglich Integriertes BMS Sehr hohe Speicherdichte – geringes Gewicht und kompakte Bauweise Absolut wartungsfrei und langlebig Vorladefunktion zum Schutz des ESS-Systems vor Überspannungsfunktion Der Elektronik-Kern – die Victron Multiplus-II Gerätekombination Der Multiplus-II ist eine High-End Gerätekombination von Victron Energy, bestehend aus 48V Batterieladegerät, Wechselrichter und Transfer-Schalter. Diese Kombination verbindet die klassischen Multiplus-Komponenten mit einem externen Stromsensor und integrierter Anti-Island-Funktion. Dadurch werden die Funktionen PowerControl und PowerAssist auf 50A erweitert und der potenzielle Einsatzbereich auf Energy-Storage-System Anwendungen ausgedehnt. Der Multiplus kann daher ideal als Backupgerät in netzgekoppelten und -unabhängigen Anlagen für die Stromversorgung eingesetzt werden. 8000 W Leistung bei nicht linearer Belastung 6400 W Dauerbelastung und 15000 W Spitzenleistung für 48V Batteriespannung 100A Transferschalter 110A Batterieladegerät Ausgangsspannung: 230 VAC, Frequenz: 50 Hz max. Wirkungsgrad: 95% Schutzklasse: IP22 Konfiguration Die Auslieferung des MultiPlus-II erfolgt standardmäßig unkonfiguriert. Sie finden hier im Downloadbereich die Konfigurations-Anleitung für das System. Sollten Sie eine Vorkonfiguration durch uns wünschen, können wir dies gern gegen Aufpreis für Sie übernehmen. Hierzu legen Sie den oben verlinkten Artikel "Offgridtec Vorkonfiguration" beim Bestellvorgang in den Warenkorb. Der Versand kann in diesem Fall 3-5 Werktage länger in Anspruch nehmen, bis die Konfiguration durchgeführt wurde. Systemüberwachung mit dem Victron Cerbo GX und GX Toch Display Mit der Cerbo GX Kommunikationszentrale können Sie Ihr System ganz einfach kontrollieren und überwachen. Die flexiblen Verbindungsmöglichkeiten maximieren Ihre Systemleistung. Die Kontrolle Ihrer Anlage ist dank des Cerbo GX ortsunabhängig möglich. Mit dem GX Touch 50 Display haben Sie alle Parameter Ihres Systems stets im Blick und können Änderungen einfach und schnell vornehmen. Sicherheitshinweis: Lassen Sie dieses Komplettsystem nur von einer Elektrofachkraft installieren und in Betrieb nehmen.

The backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. In addition to lithium-ion batteries from Pylontech, the systems include a matching MultiPlus-II inverter and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even if there is a power failure. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply of the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application of the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting of existing PV systems Grid-connected power supply UPS systems What does the Offgridtec backup system contain? Pylontech us2000c 2.4kWh LiFePO4 battery (2x or 4x depending on selection) 1x Victron MultiPlus-II 48/3000/35-32 230v device combination 1x Victron Lynx Distributor 1x Victron Cerbo gx control panel 1x Victron gx Touch 50 display panel for Cerbo gx 1x 1,8m VE.Can to Can-Bus bms type A cable 1x 3m Victron rj45 utp cable 1x 1m Offgridtec battery cable 50mm² M8 eyelets 1x 125a 70v mega fuse 1x Pylontech battery connection cable set The Multiplus device combination is pre-configured to fit the Pylontech batteries. Extended use of your backup system To establish an ESS (Energy Storage System) with the backup system, an energy meter with connection cable is required for each: • Victron VM-3P75CT Energy Meter 3-phase electricity meter 75A/phase • 5m Victron RJ45 UTP Cable With this electricity meter, you can perform a grid-parallel installation and then monitor your energy consumption or control your energy costs. Thanks to phase compensation, you can also operate the 3-phase meter for 1-phase systems. This enables seamless integration of decentralized energy sources and consumers into the existing power grid. To ensure that an ESS can be considered in the pre-configuration, the meter must be purchased in advance or as part of the system! The storage solution - Pylontech us2000c batteries The us2000c storage is a lithium battery of the latest generation. It has been specially designed to meet the high demands placed on backup storage. Thanks to state-of-the-art technology, the highest level of safety and a long service life are guaranteed, even with regular deep discharge. Extremely cycle resistant - over 6000 cycles at 95% DoD Absolutely intrinsically safe lithium technology High charge and discharge capacity possible Integrated bms Very high storage density - low weight and compact design Absolutely maintenance-free and durable Pre-charge function to protect the ESS system from overvoltage function The electronics core - the Victron Multiplus-II device combination The Multiplus-II is a high-end device combination from Victron Energy, consisting of 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus can therefore be ideally used as a backup device in grid-connected and grid-independent power supply systems. 3000W non-linear load power - 2400w continuous load - 6000w peak power for 48v battery voltage 32A transfer switch 35A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95% Protection class: IP22 System monitoring with the Victron Cerbo gx and gx Toch display Easily control and monitor your system with the Cerbo gx communication center. The flexible connectivity options maximize your system performance. Control of your system is possible regardless of location thanks to the Cerbo gx. With the gx Touch 50 display, you always have all the parameters of your system in view and can make changes easily and quickly.

The 3-phase backup systems from Offgridtec are ideal for emergency power supply or for expanding an existing solar system. The systems contain lithium-ion batteries from Pytesthe matching MultiPlus-II inverters and a Cerbo gx from Victron Energy for system monitoring. This allows you to secure your energy supply even in the event of a power failure. With the batteries from Pytes, you have a storage capacity of 20.5 kwh to 30.7 kwh, depending on your choice, to use your energy efficiently and remain self-sufficient for longer if required. Thanks to the UPS function, the MultiPlus remains switched on even in the event of a mains failure and takes over the supply to the connected consumers. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices can be guaranteed. Areas of application for the Offgridtec backup kit: Emergency power supply Off-grid solar systems (stand-alone systems) Retrofitting existing PV systems Grid-connected power supply UPS systems what does the Offgridtec backup system contain? Pytes E-Box-48100r-c 100ah 51v LiFePO4 battery (depending on selection 4-6x) 3x Victron MultiPlus-II 48/5000/70-50 230V 1x Victron Cerbo gx communication center System monitoring 1x Victron gx Touch 50 display panel for Cerbo gx 1x Victron Energy Lynx Power In (m8) 2x Victron Lynx Distributor (m8) 2x 0.9m Victron rj45 utp cable 1x 3m Victron rj45 utp cable 1x Victron mk3-usb VE.bus to usb interface 1x Pytes data cable battery to Victron Inverter 3.5m MultiPlus 2 Pytes battery inverter power cable 2m, positive (2-3x depending on selection) Pytes battery inverter power cable 2m, negative (2-3x depending on selection) 2x Offgridtec set of 5 MEGA fuses 100a 70v for 48v systems 6x Offgridtec® 1m battery cable 35mm² m8 eyelets on both sides When selecting electricity meter 1x Victron vm-3p75ct Energy Meter 1xVictron 5m rj45 utp cable Extended use of your backup system The backup kit is supplied either with or without Victron electricity meter and cable, although an energy meter is always required to set up an energy storage system. With this electricity meter, you can carry out a grid-parallel installation and then monitor your energy consumption and control your energy costs. Thanks to phase compensation, you can even use the 3-phase meter for 1-phase systems. This means that seamless integration of decentralized energy sources and consumers into the existing power grid is no problem. In order for an ess to be included in a pre-configuration, the meter must be purchased in advance or for the system! The storage solution - Pytes E-Box-481000R-C ThePytes e-box 48100r-c is a state-of-the-art LFP battery with 100 Ah capacity and is characterized by its high level of safety, sophisticated design and impressive performance. The battery is compact, easy to install, maintenance-free and can be used as the basic building block of an energy storage system by connecting it in parallel. Technical data Battery chemistry: Lithium iron phosphate (LFP) Nominal voltage: 51.2 V Voltage range: 47.5-57.6 V Rated power: 100 Ah Nominal energy: 5.12 kwh Max. Charging current: 50 A Max. Discharge: 50 A Charging temperature: 0~50°C Discharge temperature: -10~50°C efficiency: ≥95% Communication protocol: rs-232, rs-485, CAN Cycle life: >6000 cycles at 90% DoD Dimensions: 440 x 620 x 117 mm Weight: 51 kg The electronic core - the Victron Multiplus-II appliance combination The Multiplus-II is a high-end appliance combination from Victron Energyconsisting of a 48v battery charger, inverter and transfer switch. This combination combines the classic Multiplus components with an external current sensor and integrated anti-island function. This extends the PowerControl and PowerAssist functions to 50a and extends the potential range of use to energy storage system applications. The Multiplus is therefore ideal for use as a backup device in grid-connected and off-grid power supply systems. 8000 w power with non-linear load 6400 w continuous load and 15000 w peak power for 48v battery voltage 100a transfer switch 110A battery charger Output voltage: 230 vac, frequency: 50 Hz max. efficiency: 95 Protection class: IP22 Configuration The MultiPlus-II is delivered unconfigured as standard. You can find the configuration instructions for the system here in the download area. If you would like us to pre-configure the system for you, we can do this for you for an additional charge. To do this, please download the article "Offgridtec Pre-configuration" in the shopping cart during the ordering process. In this case, shipping may take 3-5 working days longer until the configuration has been completed. System monitoring with the Victron Cerbo gx and gx Toch display With the Cerbo gx communication center, you can easily control and monitor your system. The flexible connection options maximize your system performance. Thanks to the Cerbo gx, you can control your system from anywhere. With the gx Touch 50 display, you always have an overview of all your system parameters and can make changes quickly and easily. Safety note: Only have this complete system installed and commissioned by a qualified electrician.